Toshiba B Sa4t G Manual

							 
- 108 -  
 
 
 
 
 
 
 
 
 
 
 
 
  Line print for assembly process 
 
 
 
  
						

							 
- 109 -
6.6 SENSOR DISPLAY/ADJUSTMENT 
6.6.1  Sensor Display/Adjustment Operation Example 
     
Power OFF   (1)  Power off state 
             
        [FEED] [PAUSE] (2)  While holding the [FEED] and [PAUSE] keys 
down, turn the power on. 
 
< 1 > D I A G .       V 1 . 2 A
             (3)  The self-test menu is displayed. 
              
        [FEED] 
 (4)  Press the [FEED] key. 
< 2 > P A R A M E T E R    S E T
 
             
 (5)  System mode menu display 
 (Parameter setting) 
              
        [FEED] 
 (6)  Press the [FEED] key. 
< 3 > A D J U S T    S E T 
 
             
 (7)  System mode menu display 
  (Fine adjustment value setting) 
              
        [FEED] 
 (8)  Press the [FEED] key. 
< 4 > T E S T    P R I N T 
             (9)  System mode menu display 
 (Test print) 
              
        [FEED] 
 (10)  Press the [FEED] key. 
< 5 > S E N S O R    A D J .
             (11)  System mode menu display 
(Sensor display/adjustment) 
              
        [PAUSE] 
 (12)  Press the [PAUSE] key. 
< 5 > S E N S O R    A D J .
[ H ] 2 8 ° C      [ A ] 2 8 ° C(13)  Thermal head temperature/Ambient 
temperature are displayed. 
              
        [PAUSE] 
 (14)  Press the [PAUSE] key. 
< 5 > S E N S O R    A D J .
[ R E F L E C T ]      3 . 5 V
             (15)  Reflective sensor value is displayed. 
  Load tag paper so that the sensor does not 
detect a black mark. 
        [RESTART] or 
[FEED]  
(16)  Hold down the [RESTART] or [FEED] key for 3 
seconds or more. 
< 5 > S E N S O R    A D J .
[ R E F L E C T ]      4 . 8 V *(17)  “*” is displayed when the reflective sensor 
adjustment is completed. 
              
        [PAUSE] 
 (18)  Press the [PAUSE] key.  
						

							 
- 110 -  
              
< 5 > S E N S O R    A D J .
[ T R A N S . ]       2 . 4 V
             (19)  Transmissive sensor value is display: 
Remove a few labels and place the backing 
paper so that sensor can detect backing paper.
        [RESTART] or 
[FEED]  
(20)  Hold down the [RESTART] or [FEED] key for 3 
seconds or more. 
< 5 > S E N S O R    A D J .
[ T R A N S . ]       4 . 1 V *(21)  “*” is displayed when the transmissive sensor 
adjustment is completed. 
              
        [PAUSE] 
 (22)  Press the [PAUSE] key. 
< 5 > S E N S O R    A D J .
[ P E ] R 0 . 1 V    T 4 . 8 V
             (23) Reflective/transmissive sensor values (no 
paper level) are displayed. 
  Remove any paper covering the sensor. 
        [RESTART] or 
[FEED]  
(24)  Hold down the [RESTART] or [FEED] key for 3 
seconds or more. 
< 5 > S E N S O R    A D J .
[ P E ] R 0 . 1 V    T 4 . 8 V *
             (25)  “*” is displayed when the reflective/ 
transmissive sensor adjustment (no paper 
level) is completed. 
        [PAUSE] 
 (26)  Press the [PAUSE] key. 
< 5 > S E N S O R    A D J .
             (27)  System mode menu display   
(Sensor display/adjustment) 
 
  
						

							 
- 111 - 6.6.2  Details of Sensor Adjustment Value Display 
(1)  Sensor adjustment value display 
[  H ] 2 0 ° C      [ A ] 2 2 ° C
 
 
 
 
 
[  R E F L E C T ]  3 . 8 V
 
 
 
 
[  T R A N S . ]    2 . 3 V
 
 
 
[  P E ] R 0 . 2 V  T 4 . 6 V
 
 
 
 
 
(2) Supplementary explanations 
  •  During a sensor check, status of each sensor is monitored and displayed every 200 msec.   
(The display changes in accordance with sensor status.) 
  •  When the [FEED] and [RESTART] keys are pressed at the same time, the system mode 
menu is displayed. 
Ambient temperature sensor status 
(0 °C to 86 °C) 
Thermal head thermistor status 
(0 °C to 86 °C) 
No paper level of the reflective sensor   
(0.0 V to 5.0 V) 
No paper level of the transmissive sensor   
(0.0 V to 5.0 V) 
Reflective sensor status 
(0.0 V to 5.0 V) 
Transmissive sensor status 
(0.0 V to 5.0 V)  
						

							 
- 112 -
6.7 RAM CLEAR 
6.7.1  RAM Clear Operation Example 
     
Power OFF   (1)  Power off state 
             
        [FEED] [PAUSE] (2)  While holding the [FEED] and [PAUSE] keys 
down, turn the power on. 
 
< 1 > D I A G .       V 1 . 2 A
             (3)  The self-test menu is displayed. 
              
        [FEED] 
 (4)  Press the [FEED] key. 
< 2 > P A R A M E T E R    S E T
 
             
 (5)  System mode menu display 
 (Parameter setting) 
              
        [FEED] 
 (6)  Press the [FEED] key. 
< 3 > A D J U S T    S E T 
 
             
 (7)  System mode menu display 
  (Fine adjustment value setting) 
              
        [FEED] 
 (8)  Press the [FEED] key. 
< 4 > T E S T    P R I N T 
             (9)  System mode menu display 
 (Test print) 
              
        [FEED] 
 (10)  Press the [FEED] key. 
< 5 > S E N S O R    A D J .
             (11)  System mode menu display 
(Sensor display/adjustment) 
              
        [FEED] 
 (12)  Press the [FEED] key. 
< 6 > R A M    C L E A R   
             (13)  System mode menu display 
(RAM clear) 
              
        [PAUSE] 
 (14)  Press the [PAUSE] key. 
< 6 > R A M    C L E A R   
N O    R A M    C L E A R   
             (15)  No RAM clear mode 
  (*) A mode to prevent RAM clear from being 
performed mistakenly 
        [FEED] 
 (16)  Press the [FEED] key. 
< 6 > R A M    C L E A R   
M A I N T E . C N T    C L E A R(17)  Maintenance counter clear mode 
              
        [FEED] 
 (18)  Press the [FEED] key.  
						

							 
- 113 -  
              
< 6 > R A M    C L E A R   
P A R A M E T E R    C L E A R(19)  Parameter clear mode 
              
        [PAUSE] 
 (20)  Press the [PAUSE] key. 
< 6 > R A M    C L E A R   
* * *    Q M    T Y P E    * * *(21)  RAM clear for the QM type 
              
        [FEED] 
 (22)  Press the [FEED] key. 
< 6 > R A M    C L E A R   
* * *    J A    T Y P E    * * *(23)  RAM clear for the JA type 
              
        [PAUSE] 
 (24)  Press the [PAUSE] key. 
< 6 > R A M    C L E A R   
*             (25)  Parameter clear is executed. 
              
         
  
< 6 > R A M    C L E A R   
* *             
              
         
  
< 6 > R A M    C L E A R   
* * *           (26) Progress display 
              
         
  
< 6 > R A M    C L E A R   
* * * * * * * * * * * * * * * * 
              
         
  
< 6 > R A M    C L E A R   
* * *    C O M P L E T E    * * *(27)  Parameter clear is complete. 
             (28)  Turn the power off. 
         
  
             
              
 
 
Select a type 
according to a 
destination
. 
						

							 
- 114 - 6.7.2  Details of RAM Clear   
(1)  RAM clear mode 
 
  •  NO RAM CLEAR 
 • MAINTE.CNT CLEAR 
 • PARAMETER CLEAR 
 
 
(2) Destination type 
 
  •  QM TYPE (for North/South America/Europe/Asia/China) 
  •  JA TYPE (for Japan) 
  
 
 
(3) Supplementary explanations 
•  When the [FEED] and [RESTART] keys are pressed at the same time, the display shows 
the system mode menu. 
•  When “COMPLETE” is displayed after a RAM clear is complete, turn off the power. 
• The total label distance covered, sensor adjustment values (system mode ), the IP 
address setting, socket communication port number, languages for LCD messages, and 
data of flash memory on the CPU are not cleared by a RAM clear. 
•  The number of times a tag data write succeeded and the number of times a tag data write 
failed are not cleared by a RAM clear. 
•  Password setting to protect error tag detection, access password setting, and automatic 
unlock function setting cannot be cleared by RAM clear.    (The initial values in the table 
are the factory default.)   
•  Destination type ([QM] or [JA]) is printed on the upper right area of a maintenance counter 
printout.    
(4)  Values after maintenance counter clear 
Item Value 
Label distance covered  0 km 
Print distance  0 km 
Cut count  0 
Ribbon motor drive time  0 hours 
RS-232C hardware error count  0 
System error count  0 
Momentary power interruption count  0 
 
FEED 
RESTART 
FEED 
RESTART  
						

							 
- 115 - (5)  Values after parameter clear 
Parameter Value 
Feed amount fine adjustment (PC)  0 mm 
Cut (strip) position fine adjustment (PC)  0 mm 
Reverse feed amount fine adjustment (PC)  0 mm 
Print tone fine adjustment: 
  Thermal transfer print mode (PC) 0 
Print tone fine adjustment: 
  Direct thermal print mode (PC) 0 
Ribbon motor drive voltage fine adjustment   
(Take-up) (PC) 0 
Ribbon motor drive voltage fine adjustment   
(Feed) (PC) 0 
Feed amount fine adjustment (Key)  0 mm 
Cut (strip) position fine adjustment (Key)  0 mm 
Reverse feed amount fine adjustment (Key)  0 mm 
Print tone fine adjustment: 
  Thermal transfer print mode (Key) 0 
Print tone fine adjustment: 
  Direct thermal print mode (Key) 0 
Ribbon motor drive voltage fine adjustment   
(Take-up) (Key) 0 
Ribbon motor drive voltage fine adjustment   
(Feed) (Key) 0 
X-coordinate fine adjustment (Key)  0 mm 
Transmissive sensor manual threshold fine 
adjustment value 1.4 V 
Reflective sensor manual threshold fine adjustment 
value 1.0 V 
Character code  PC-850 
Font “0”  “0” (without slash) 
RS232C communication speed  9600 bps 
RS232C data length    8 bits 
RS232C stop bit length  1 bit 
QM type  NONE RS232C parity 
JA type  EVEN 
RS232C flow control method XON/XOFF + READY/BUSY (DTR) 
protocol: 
(XON when the power is on, XOFF 
when the power is off) 
QM type  English Language for LCD messages 
JA type  Japan 
Forward feed standby after an issue OFF 
(ON when the cutter is attached.)   
Control code    Auto 
Strip wait status  OFF 
[FEED] key function  FEED (Feeds one label.) 
Kanji code  TYPE1 
Euro code  B0H 
Automatic head broken dots check  OFF 
Centronics ACK/BUSY timing  TYPE1  
						

							 
- 116 -  
Parameter Value 
Web printer function  OFF 
Reset process when the nInit signal is ON  OFF 
Ribbon near end detection    OFF 
Expansion I/O operation mode  Normal 
Plug-and-play operation mode  OFF 
Label end/ribbon error process    The printer stops an issue operation.
Pre-strip process    OFF 
Reverse feed speed    3 ips 
MaxiCode specification    TYPE1 
Keyboard I/F  OFF 
Automatic calibration  OFF 
LAN enable/disable  Enable 
Status response  ON 
Label pitch  76.2 mm 
Effective print length  74.2 mm 
203 dpi 
104.0 mm Effective print width 
300 dpi 
105.7 mm 
Print method  Thermal transfer print mode 
Sensor type  Transmissive sensor 
Feed speed 
4”/sec. 
Issue mode  Batch 
PC-save automatic call  ON 
BASIC interpreter setting  OFF 
BASIC interpreter trace setting  OFF 
DHCP setting  OFF 
RFID module type selection  NONE 
RFID tag type selection  NONE 
RFID module’s destination code setting 
(user-inaccessible setting) *Supported from C2.0CDepending on the module setting 
(Supported from C2.0C) 
RFID error tag detection  OFF 
Password setting to protect error tag detection  Disabled: 0000 
Access password setting  00000000 
Automatic unlock function setting  Disabled 
Max. number of issue retires  3 
Max. number of read retires  5 
Read retry time-out  4.0 seconds 
Max. number of write retries  5 
Write retry time-out  2.0 seconds 
RFID adjustment for retry  OFF: +00 mm 
Radio output power level  251 
AGC threshold  0 
RFID channel   
(Not available to the B-SA704-RFID-U2-R) AUTO 
Q value  2 
AGC threshold for data write  11 
AGC threshold lower limit for retry  11 
Hibiki tag multi-word write  0: OFF  
						

							 
- 117 - Parameter Value 
System mode password setting  OFF 
Strip motor torque  R0 
Print head applied current table setting  TYPE1 
High speed cut issue  TYPE1 
Multiple-label set issue  OFF 
Z-Mode (C1.9A or later)  OFF