Toshiba B Sa4t G Manual

							 
- 128 -  
              
< 8 > B A S I C          
0 1    T E S T . D A T     (37)  Data file display 
             
             (38)  Names of data files, saved in the BASIC file 
area, are displayed. 
< 8 > B A S I C          
0 0    T E S T . B A S     (39)  Program file display 
              
        [PAUSE] 
 (40)  Press the [PAUSE] key. 
< 8 > B A S I C          
B A S I C    T R A C E     (41)  BASIC trace setting 
              
        [PAUSE] 
 (42)  Press the [PAUSE] key. 
< 8 > B A S I C          
T R A C E            O F F (43)  BASIC trace setting (Disabled) 
              
        [FEED] 
 (44)  Press the [FEED] key. 
< 8 > B A S I C          
T R A C E            O N   (45)  BASIC trace setting (Enabled) 
              
        [PAUSE] 
 (46)  Press the [PAUSE] key. 
< 8 > B A S I C          
E X P A N D    M O D E     (47)  BASIC expansion mode   
              
        [PAUSE] 
 
(48) Press the [PAUSE] key to execute the BASIC 
expansion mode program, if it has been 
loaded. 
The basic expansion mode ends when the 
basic expansion program is exited. 
 
< 8 > B A S I C          
             (49)  BASIC setting mode 
  
						

							 
- 129 -
6.10  ADJUSTMENT MODE FOR FACTORY 
     
Power OFF    
              
        
        [FEED] [PAUSE] 
(1)  While holding the [FEED] and [PAUSE] keys 
down, turn the power on. 
 
< 1 > D I A G .       V 1 . 2 A
             (2)  The self-test menu is displayed. 
              
        [FEED] 
 (3)  Press the [FEED] key. 
< 2 > P A R A M E T E R    S E T
 
             
 (4)  System mode menu display 
 (Parameter setting) 
              
        [FEED] 
 (5)  Press the [FEED] key. 
< 3 > A D J U S T    S E T 
 
             
 (6)  System mode menu display 
  (Fine adjustment value setting) 
              
        [FEED] 
 (7)  Press the [FEED] key. 
< 4 > T E S T    P R I N T 
             (8)  System mode menu display 
 (Test print) 
              
        [FEED] 
 (9)  Press the [FEED] key. 
< 5 > S E N S O R    A D J .
             (10)  System mode menu display 
(Sensor display/adjustment) 
              
        [FEED] 
 (11)  Press the [FEED] key. 
< 6 > R A M    C L E A R   
             (12)  System mode menu display 
(RAM clear) 
              
        [FEED] 
 (13)  Press the [FEED] key. 
< 7 > I P    A D D R E S S 
             (14)  System mode menu display 
(IP address setting) 
              
        [FEED] 
 (15)  Press the [FEED] key. 
< 8 > B A S I C          
             (16)  System mode menu display 
(BASIC setting) 
              
        [FEED] 
 (17)  Press the [FEED] key.  
						

							 
- 130 -  
              
< 9 > F O R    F A C T O R Y
             (18)  The menu for the adjustment mode for the 
factory is displayed. 
              
        [PAUSE] 
 (19)  Press the [PAUSE] key. 
< 9 > F O R    F A C T O R Y
O P T I O N    C H E C K   (20)  Option check mode display 
              
        [PAUSE] 
 (21)  Press the [PAUSE] key. 
< 9 > F O R    F A C T O R Y
O P T I O N    C H E C K    O K(22)  Option check result display 
              
        [PAUSE] 
 (23)  Press the [PAUSE] key. 
< 9 > F O R    F A C T O R Y
             (24)  The display is returned to the menu for the 
adjustment for the factory. 
 
 NOTE: Option Check  
 Currently no option checks are performed and fixed to OK.  
						

							 
- 131 -
6.11 RFID SETTING 
6.11.1  RFID Setting Operation Example 
     
Power OFF   (1)  Power off state 
              
        
        [FEED] [PAUSE] 
(2)  While holding the [FEED] and [PAUSE] keys 
down, turn the power on. 
 
< 1 > D I A G .       V 1 . 2 A
             (3)  The self-test menu is displayed. 
              
        [FEED] 
 (4)  Press the [FEED] key. 
< 2 > P A R A M E T E R    S E T
 
             
 (5)  System mode menu display 
 (Parameter setting) 
              
        [FEED] 
 (6)  Press the [FEED] key. 
< 3 > A D J U S T    S E T 
 
             
 (7)  System mode menu display 
  (Fine adjustment value setting) 
              
        [FEED] 
 (8)  Press the [FEED] key. 
< 4 > T E S T    P R I N T 
             (9)  System mode menu display 
 (Test print) 
              
        [FEED] 
 (10)  Press the [FEED] key. 
< 5 > S E N S O R    A D J .
             (11)  System mode menu display 
(Sensor display/adjustment) 
              
        [FEED] 
 (12)  Press the [FEED] key. 
< 6 > R A M    C L E A R   
             (13)  System mode menu display 
(RAM clear) 
              
        [FEED] 
 (14)  Press the [FEED] key. 
< 7 > I P    A D D R E S S 
             (15)  System mode menu display 
(IP address setting) 
              
        [FEED] 
 (16)  Press the [FEED] key.  
						

							 
- 132 -  
              
< 8 > B A S I C          
             (17)  System mode menu display 
(BASIC setting) 
              
        [FEED] 
 (18)  Press the [FEED] key. 
< 9 > F O R    F A C T O R Y
             (19)  The menu for the adjustment mode for the 
factory is displayed. 
              
        [FEED] 
 (20)  Press the [FEED] key. 
< 1 0 > R F I D          
             (21)  RFID setting menu display 
              
        [PAUSE] 
 (22)  Press the [PAUSE] key. 
< 1 0 > R F I D          
R E A D    T E S T          O F F
             (23)  RFID read test menu   
Enable/Disable the read test by using the 
[FEED] or [RESTART] key. 
        [PAUSE] 
 (24)  Press the [PAUSE] key. 
< 1 0 > R F I D          
C A R E E R S E N S E      O F F
             (25)  RFID carrier sense setting   
Enable/Disable the carrier sense test by using 
the [FEED] or [RESTART] key. 
        [PAUSE] 
 (26)  Press the [PAUSE] key. 
< 1 0 > R F I D          
M O D U L E              N O N E
             (27)  RFID module type setting 
Select a type by using the [FEED] or 
[RESTART] key. 
        [PAUSE] 
 (28)  Press the [PAUSE] key. 
< 1 0 > R F I D          
T A G    N O N E        
             (29)  RFID tag type setting 
Select a tag type by using the [FEED] or 
[RESTART] key. 
        [PAUSE] 
 (30)  Press the [PAUSE] key. 
< 1 0 > R F I D          
C O U N T R Y        E U 0 
             (31)  RFID module’s destination code setting
  
(user-inaccessible setting) (U2 only)  
Make a choice by using the [FEED] or 
[RESTART] key. 
        [PAUSE] 
 (32)  Press the [PAUSE] key. 
< 1 0 > R F I D          
E R R  C H K       O F F
             (33)  RFID error tag detection   
Enable/Disable the detection by using the 
[FEED] or [RESTART] key. 
        [PAUSE] 
 (34)  Press the [PAUSE] key. 
  
						

							 
- 133 -  
< 1 0 > R F I D          
I S S U E    R E T R Y      3
             (35)  Maximum number of issue retries setting 
Set a value by using the [FEED] or [RESTART] 
key. 
        [PAUSE] 
 (36)  Press the [PAUSE] key. 
< 1 0 > R F I D          
R    C Y C L E    C N T      5
             (37)  Maximum number of read retries setting 
Set a value by using the [FEED] or [RESTART] 
key. 
        [PAUSE] 
 (38)  Press the [PAUSE] key. 
< 1 0 > R F I D          
R  C Y C L E  T I M    4 . 0
             (39)  Read retry time-out setting 
Set a value by using the [FEED] or [RESTART] 
key. 
        [PAUSE] 
 (40)  Press the [PAUSE] key. 
< 1 0 > R F I D          
W    C Y C L E    C N T      5
             (41)  Maximum number of write retries setting 
Set a value by using the [FEED] or [RESTART] 
key. 
        [PAUSE] 
 (42)  Press the [PAUSE] key. 
< 1 0 > R F I D          
W  C Y C L E  T I M    2 . 0
             (43)  Write retry time-out setting 
Set a value by using the [FEED] or [RESTART] 
key. 
        [PAUSE] 
 (44)  Press the [PAUSE] key. 
< 1 0 > R F I D          
A D J    R E T R Y          + 0 0
             (45)  RFID adjustment for retry 
Set a value by using the [FEED] or [RESTART] 
key. 
        [PAUSE] 
 (46)  Press the [PAUSE] key. 
< 1 0 > R F I D          
P O W E R    L E V E L      1 8
             (47)  Radio output power level setting 
Set a value by using the [FEED] or [RESTART] 
key. 
        [PAUSE] 
 (48)  Press the [PAUSE] key. 
< 1 0 > R F I D          
A G C    T H R E S H O L D  0
             (49)  AGC threshold setting 
Set a value by using the [FEED] or [RESTART] 
key. 
        [PAUSE] 
 (50)  Press the [PAUSE] key. 
< 1 0 > R F I D          
R F    C H A N N E L      A U T O
             (51)  RFID channel setting 
This menu is not available to the B-SA704-
RFID-U2-EU-R. 
        [PAUSE] 
 (52)  Press the [PAUSE] key. 
  
						

							 
- 134 -  
< 1 0 > R F I D          
Q  V A L U E        2
             (53)  Q value setting 
Set a value by using the [FEED] or [RESTART] 
key. 
        [PAUSE] 
 (54)  Press the [PAUSE] key. 
< 1 0 > R F I D          
W T  A G C         1 1
             (55)  AGC threshold for data write   
Set a value by using the [FEED] or [RESTART] 
key. 
        [PAUSE] 
 (56)  Press the [PAUSE] key. 
< 1 0 > R F I D          
W T    M I N    A G C        1 1
             (57)  AGC threshold lower limit for retry 
Set a value by using the [FEED] or [RESTART] 
key. 
        [PAUSE] 
 (58)  Press the [PAUSE] key. 
< 1 0 > R F I D          
M U L T    W R I T E    O F F
             (59)  Hibiki tag multi-word write 
Enable/disable the function by using the 
[FEED] or [RESTART] key. 
        [PAUSE] 
 (60)  Press the [PAUSE] key. 
< 1 0 > R F I D          
             (61)  RFID setting menu display  
						

							 
- 135 - 6.11.2  Details of RFID Setting 
(1)  RFID read test 
 
 
 
 
 
 
 
  OFF:  A read test is not performed. 
  ON:  The printer enters read test mode, and a read test is performed each time the 
[PAUSE] key is pressed.    The read data on the tag is displayed on the LCD.   
When the tag cannot be read, “RFID TIMEOUT” or “RFID READ ERROR” is 
displayed. 
If the type of the tag to be read and one selected by the RFID tag type selection 
menu do not match, an RFID tag read error will result.    Make sure the RFID tag 
type has been selected before the read test is started. 
  Read data is displayed in hex. value, up to 14 bytes on 2 lines.    The data to be 
displayed is the EPC code in the EPC area of a tag.   
 
 
When the RFID tag contains 14 bytes or more data, the first 14 bytes are displayed. 
When data volume is less than 14 bytes, the vacant digits will be filled with spaces.   
The right most hex. value on the lower line, enclosed with parentheses, indicates an 
AGC value of a read tag.    When more than one tag is read at one time, especially 
when short-pitch tags are used, pressing the [FEED] or [RESTART] key shows the 
other tags’ data.    Among them, a tag with the highest AGC value is considered to 
be positioned just above the antenna.   
When the RFID module type is set to “NONE” or a communication cannot be 
established, a message, “NO RFID MODULE”, is displayed.   
 
 
(2)  RFID carrier sense setting (Not available to the B-SA704-RFID-U2-EU-R.) 
 
(3)  RFID module type 
 
 
 
 
 
 
 
  NONE:  No RFID kits are installed.   
 U1: Reserved.  
  H1:  Reserved.   
 H2: Reserved. 
 U2: B-SA704-RFID-U2-¼¼-R 
  NOTE:  The module type changed by using this menu becomes effective after the power is 
turned off and back to on.   
FEED 
RESTART 
FEED 
RESTART 
OFF: A read test is not performed. 
 
ON: A read test is performed. 
 
1234567890123456
65432109    (0E)
U1: Reserved. 
H1: Reserved. 
NONE: No RFID Module is installed. 
U2: B-SA704-RFID-U2-¼¼-R 
H2: Reserved.
  
						

							 
- 136 - (4)  RFID tag type   
Module type: U2 
 
 
 
 
 
 
 NOTE: 
  1.  The tag type changed by using this menu becomes effective after the power is turned off 
and back to on.   
  2.  Only tag type options which are available to the selected module type are displayed.   
 
(5)  RFID error tag detection   
  EPC:  An error tag detection is performed.   A tag (EPC area for Gen2 tags) is read before 
writing data on it and data is written on the tag only when the header data is “A5A5”.   
  OFF:  An error tag detection is not performed.    Though a tag is read before writing data on 
it, data is always written on the tag whatever data is set as the header data.   
  PASS:  An error tag detection is performed only for Gen2 tags.    The access password area 
of a tag is read before writing data on it.    Only when the data read matches the 
access password setting data, the data is written on the tag. 
 
  To prevent unauthorized changes of the setting, a password to protect the error tag 
detection setting can be programmed.   
 
FEED 
RESTART NONE (No tag type selection) 
24: EPC C1 Gen2
 
PASSWORD    0200
PASSWORD    0E00PAUSE 
RESTART
FEED
FEED
RESTARTRESTART 
FEED 
FEED 
RESTART PASSWORD    0F00
PASSWORD    0100
ERR CHK    OFF
ERR CHK    CHG
PASSWORD    1000PASSWORD    2000
PASSWORD    E000
to the next setting PAUSE 
RESTART 
RESTART FEED  FEED 
PAUSE 
PAUSE 
When the system enters this menu, the 
current setting is displayed and when “CHG”
is selected, the setting can be changed. 
If the password to protect the error tag 
detection setting has been enabled, an entry 
of the password is requested. 
Password 
protect has 
been enabled.
Password protect 
has been disabled.
 RESTART
FEED
FEED
RESTARTRESTART 
FEED 
FEED 
RESTART PASSWORD    F000
PASSWORD    0000
PASSWORD    0000
A B  
						

							 
- 137 -  
 
PAUSE 
A.PASS 00000000 
A.PASS 20000000
A.PASS E0000000PAUSE 
PAUSE 
A.PASS 00000000 
A.PASS 00000002
A.PASS 0000000E
PAUSE 
Enter an 8-digit access password. 
RESTART
FEED
FEED
RESTARTRESTART 
FEED 
FEED 
RESTART 
RESTART
FEED
FEED
RESTARTRESTART 
FEED 
FEED 
RESTART 
A.PASS 10000000
A.PASS F0000000
A.PASS 00000001
A.PASS 0000000F
ERR CHK    OFF
ERR CHK    EPC
ERR CHK    PASS
to the next setting
PAUSE 
PAUSE  RESTART
RESTART FEED
FEEDPassword matches. 
When selecting “PASS”, an entry of the access 
password is required. 
Password does not match. 
PASSWORD    0020
PASSWORD    00E0
PASSWORD    0002
PASSWORD    000E
PAUSE 
PAUSE 
RESTART
FEED
FEED
RESTARTRESTART 
FEED 
FEED 
RESTART 
PASSWORD    0010
PASSWORD    00F0
PASSWORD    0001
PASSWORD    000F
RESTART
FEED
FEED
RESTARTRESTART 
FEED 
FEED 
RESTART 
PASSWORD    0000
PASSWORD    0000
A 
C 
B