Toshiba B Sa4t G Manual

							 
- 98 - (2) Test print for assembly process 
     
Power OFF   (1)  Power off state 
             
        [FEED] [PAUSE] (2)  While holding the [FEED] and [PAUSE] keys 
down, turn the power on.   
< 1 > D I A G .       V 1 . 2 A
             (3)  The self-test menu is displayed. 
              
        [FEED] 
 
(4)  Press the [FEED] key. 
< 2 > P A R A M E T E R    S E T
 
             
 (5)  System mode menu display 
 (Parameter setting) 
              
        [FEED] 
 
(6)  Press the [FEED] key. 
< 3 > A D J U S T    S E T 
 
             
 (7)  System mode menu display 
  (Fine adjustment value setting) 
              
        [FEED] 
 
(8)  Press the [FEED] key. 
< 4 > T E S T    P R I N T 
             (9)  System mode menu display 
(Test print) 
              
        [PAUSE] 
 (10)  Press the [PAUSE] key. 
< 4 > T E S T    P R I N T 
P R I N T    C O N D I T I O N(11)  Test print condition setting mode 
              
        [RESTART] 
 (12)  Press the [RESTART] key. 
< 4 > T E S T    P R I N T 
A U T O    P R I N T ( R E F L )(13)  Assembly process automatic print mode 
(Reflective sensor) 
              
        [PAUSE] 
 
(14)  Press the [PAUSE] key. 
    One label is fed. 
3-dot slant line: 5 labels are printed. 
< 4 > T E S T    P R I N T 
A U T O    P R I N T ( R E F L )(15)  Assembly process automatic print mode 
(Reflective sensor) 
              
        [PAUSE] 
 
(16)  Press the [PAUSE] key. 
(Bar code: 5 labels are printed.) 
< 4 > T E S T    P R I N T 
A U T O    P R I N T ( R E F L )(17)  Assembly process automatic print mode 
(Reflective sensor) 
              
        [PAUSE] 
 
(18)  Press the [PAUSE] key. 
(Characters: 5 labels are printed.)  
						

							 
- 99 -  
< 4 > T E S T    P R I N T 
             (19)  System mode menu display 
(Test print) 
              
        [PAUSE] 
 (20)  Press the [PAUSE] key. 
< 4 > T E S T    P R I N T 
A U T O    P R I N T ( T R A N )(21)  Assembly process automatic print mode 
(Transmissive sensor) 
             
        
[PAUSE] (22)  Press the [PAUSE] key. 
    One label is fed. 
3-dot slant line: 5 labels are printed. 
< 4 > T E S T    P R I N T 
A U T O    P R I N T ( T R A N )(23)  Assembly process automatic print mode 
(Transmissive sensor) 
              
        [PAUSE] 
 
(24)  Press the [PAUSE] key. 
(Bar code: 5 labels are printed.) 
< 4 > T E S T    P R I N T 
A U T O    P R I N T ( T R A N )(25)  Assembly process automatic print mode 
(Transmissive sensor) 
              
        [PAUSE] 
 
(26)  Press the [PAUSE] key. 
(Characters: 5 labels are printed.) 
< 4 > T E S T    P R I N T 
             (27)  System mode menu display 
(Test print) 
  
						

							 
- 100 - 6.5.2  Details of Test Print Setting   
(1)  Test print mode 
 • PRINT CONDITION (Test print condition parameters) 
  •  SLANT LINE(1DOT)  (1-dot slant line print) 
  •  SLANT LINE(3DOT)  (3-dot slant line print) 
 • CHARACTERS (Character print) 
  •  BARCODE  (Bar code print) 
 • NON-PRINTING (Nothing prints.) 
  •  FACTORY TEST  (Line print for assembly process) 
 • AUTO PRINT(TRAN) (Assembly process automatic 
print/transmissive sensor) 
  •  AUTO PRINT(REFL)  (Assembly process automatic print/reflective 
sensor) 
 
(2)  Test print condition parameters (PRINT CONDITION) 
  •  ISSUE COUNT  (Issue count) 
  •  PRINT SPEED  (Print speed) 
 • SENSOR (Sensor) 
  •  PRT TYPE  (Print method) 
 • TYPE  (Issue mode) 
  •  LABEL LEN.  (Label length) 
  •  PAPER FEED  (Paper feed mode) 
  •   TEST PRINT  (Test print mode) 
 • PRINT CONDITION (Test print condition parameters) 
 
(3)  Issue count (ISSUE COUNT) 
 • 5000 (Issue count: 5000) 
 • 1000 (Issue count: 1000) 
 • 500 (Issue count: 500) 
 • 100 (Issue count: 100) 
 • 50 (Issue count: 50) 
 • 10 (Issue count: 10) 
 • 5 (Issue count: 5) 
 • 3 (Issue count: 3) 
 • 1 (Issue count: 1) 
 
(4)  Print speed (PRINT SPEED) 
  
  •  6 ips  (6 inches/sec)  
  •  4 ips  (4 inches/sec)     
  •  2 ips  (2 inches/sec)     
 
FEED 
RESTART 
PAUSE 
FEED 
RESTART 
FEED 
RESTART  
						

							 
- 101 - (5) Sensor (SENSOR) 
  
  •  NONE  (No sensors used) 
 • REFLECT. (Reflective sensor) 
 • TRANS. (Transmissive sensor) 
 
 
 
(6)  Print type (PRT TYPE) 
 
 • TRANSFR (Thermal transfer) 
 • DIRECT (Direct thermal) 
 
 
 
(7)  Issue type (TYPE) 
  
  •  [S] NO CUT  (Batch issue mode) 
  •  [C] WITH CUT  (Cut issue mode) 
  •  [H] PEEL OFF  (Strip issue mode) 
 
 
(8)  Label length (LABEL LEN.) 
  •  999  (Label length: 999 mm) 
  •  998  (Label length: 998 mm) 
  •  997  (Label length: 997 mm) 
    
  •  7  (Label length: 7 mm) 
  •  6  (Label length: 6 mm) 
  •  5  (Label length: 5 mm) 
 
(9)  Paper feed (PAPER) 
 
  •  FEED  (Paper feed is performed.) 
  •  NO FEED  (Paper feed is not performed.) 
 
FEED 
RESTART 
FEED 
RESTART 
FEED 
RESTART 
FEED 
RESTART 
FEED 
RESTART  
						

							 
- 102 - (10)  Parameter values after the power is turned off and on again 
  •  Menu selection:  Test print condition parameter setting 
  •  Issue count (ISSUE COUNT):  1 
  •  Print speed (PRINT SPEED):  4 ips   
 • Sensor (SENSOR): Transmissive sensor 
  •  Print type (PRT TYPE):  Thermal transfer print mode 
  •  Issue type (TYPE):  Batch issue 
  •  Label length (LABEL LEN.):  76 mm 
  •  Paper feed (PAPER):  Paper feed is performed. 
(11) Supplementary explanations 
  •  When the [FEED] and [RESTART] keys are pressed at the same time, the display shows 
the system mode menu. 
  •  If the [RESTART] or [FEED] key is held down for 0.5 seconds or more when a parameter 
is being set or a menu is being selected, the printer enters repeat mode, in which the key 
is entered repeatedly. 
  •  Each fine adjustment parameter is effective for test print except the X-coordinate fine 
adjustment. 
  •  When an error occurs during a test print, an error message is displayed and printing 
stops.  The error is cleared by pressing the [PAUSE] key and the display shows the 
system mode menu.    Printing is not automatically resumed after the error is cleared. 
  •  A selected menu or changed parameter becomes effective by pressing the [PAUSE] key 
and is retained until the power is turned off. 
  •  A label length, larger than the image buffer length, is not acceptable.    If the label length 
is larger than the image buffer length, the printer prints data (= image buffer length) then 
stops, or the printer stops because of an error. 
  •  The test print for the assembly process is performed under the following conditions.     
Parameter values and a print density fine adjustment value are ignored. 
  • Operations: c  Feeds one label. 
    d  Prints 3-dot slant lines. 
    e  Prints bar codes. 
    f Prints characters. 
    •  Issue count:  5 labels for each print operation 
    •  Print speed:  4 ips 
  • Sensor:  Reflective or transmissive sensor 
    •  Print type:  Thermal transfer print mode 
    •  Issue mode:  Batch issue 
    •  Label length:  76 mm 
    •  Print density fine adjustment value:  ±0 
  •  When the transmissive sensor is selected, the gap length between labels should be 3 
mm.  
						

							 
- 103 -   •  Enlarged view of slant lines 
    1-dot slant line print (Print ratio: 16.7%)
 
  
 
 
 
 
 
    3-dot slant line print (Print ratio: 16.7%)
 
  
 
 
 
 
 
  
						

							 
- 104 - 6.5.3  Test Print Samples 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  1-dot slant line print   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  3-dot slant line print 
 
 
  
						

							 
- 105 -  
 
  Character print (203 dpi) 
 
 
 
Character print (300 dpi) 
  
						

							 
- 106 -
 
 
 
Character print (Chinese 203 dpi)  
*Supported by C2.0D or later 
 
 
 
 
Character print (Chinese 300 dpi)  
*Supported by C2.0D or later  
						

							 
- 107 - 
 
  Bar code print (203 dpi) 
 
 
Bar code print (300 dpi)