Toshiba B Sa4t G Manual

 
- 78 - (22)  Label end/ribbon error process (LBL/RBN END) 
 
  •  TYP1:  When a label end or ribbon error state is detected, the printer 
stops even if it is printing. 
  •  TYP2:  When a label end or ribbon error state is detected, the printer 
prints the current label as far as possible, then stops. 
 
  •  TYP1:  When a label end or a ribbon error is detected in the middle of printing, the printing 
immediately stops.  When the printer is restarted, it feeds a paper first, then 
resumes the printing...

 
- 79 - •  When a ribbon error is detected where the remaining label length is less than 30 
mm, the printer completes printing the current label, then stops operation when 
the next label is fed to the home position, displaying an error message, “RIBBON 
ERROR   X”.  (“X” indicates the number of remaining labels to be printed.) 
[Number of remaining labels to be printed] = [Total number of labels to be printed] 
− [Number of printed labels including the label at which the error occurred] 
When a ribbon...

 
- 80 - (23)  Pre-strip process (PRE PEEL OFF) 
 
 
  •  OFF:  The pre-strip function is enabled. 
  •  ON:  The pre-strip function is disabled. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
4 mm           
              
 3 mm           
              
              
        
              
          2 mm  
              
 
    
1 mm       
          
6 mm  
  
      
              
              
              
PRE PEEL OFF    OFF 
PRE PEEL ON    ON 
P.P.FEED  +0.0mm 
P.P.FEED  +0.1mm 
P.P.FEED...

 
- 81 - (24)  Reverse feed speed (BACK SPEED) 
 
 • STD: 3 ips 
 • LOW: 2 ips 
 
 
 
 
(25)  MaxiCode specification (MAXI CODE) 
 
  •  TYPE1:  Compatible with a current version 
 • TYPE2: Special specification 
 
 
A mode specified by a command may be different from an actual mode, depending on the 
status of this parameter.    Also, the data transmission method differs partly.     
For details, refer to the B-SA4T External Equipment Interface Specification.   
 
 
(26)  Keyboard I/F (KB I/F) 
 
 •...

 
- 82 - (28)  Print head applied current table setting (TONE TABLE) 
 
 
 • TYPE1: Standard table 
  •  TYPE2:  Additional table 1 
 
 
 
 
Supplementary explanations 
  • When the [RESTART] and [FEED] keys are pressed at the same time, the display 
returns to the System mode menu display. 
  •  If the [RESTART] or [FEED] key is held down for 0.5 seconds or more when a parameter 
is being set, the printer enters repeat mode, in which the key is entered repeatedly. 
  •  A changed parameter is stored in...

 
- 83 - (30)  Multiple-label set issue (MULTI LABEL) 
 
 
  •  OFF:  Disabled (Normal operation) 
  •  ON:  Enabled (Multiple labels are issued as a set.) 
 
 
 
Supplementary explanations 
  •  When “No sensor” is selected, this function is invalid.     
  • When the automatic calibration is enabled, the actual label pitch is automatically 
measured, which disables this function.   Therefore, the automatic calibration needs to 
be set to OFF.   
  •  Up to 8 labels per set can be specified.     
  •...

 
- 84 - (31) System mode password setting (PASSWORD) 
 
 
 
  • With the system mode password parameter set to ON, a password entry window 
appears when either of the following occurs: a) “system mode for service persons and 
system administrators” is invoked, b) “system mode for users” is invoked, or c) the 
[PAUSE] and [RESTART] keys are held down for 3 seconds to invoke the system mode.     
When the password, which is the same as that registered here, is entered in the 
password entry window, the...

 
- 85 -   •  System mode password entry 
 
 
 
 
Enter system password mode   
(while holding the [FEED]+[RESTART] keys down, turn the power on,   
while holding the [FEED] and [PAUSE] keys down, turn the power on, or 
press the [PAUSE] key in online mode, then the [RESTART] key for 3 seconds.     
System password enabled     System password disabled     
System password accepted 
System password 
not accepted 
At power on 
From online modeStart from online mode 
Printer lock-up 
System password not...

 
- 86 -
6.4  FINE ADJUSTMENT VALUE SETTING 
6.4.1  Fine Adjustment Value Setting Operation Example 
     
Power OFF   (1)  Power off state 
             
        [FEED] [PAUSE] (2)  While holding the [FEED] and [PAUSE] keys 
down, turn the power on. 
 
< 1 > D I A G .       V 1 . 2 A(3)  The self-test menu is displayed. 
              
              
        [FEED] 
 
(4)  Press the [FEED] key. 
< 2 > P A R A M E T E R    S E T
 
             
 (5)  System mode menu display 
 (Parameter setting)...

 
- 87 -  
              
< 3 > A D J U S T    S E T 
 
T O N E    A D J . < D >    - 2
 
             (19)  Print tone fine adjustment   
(Direct thermal print mode): 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys. 
        [PAUSE] 
 
(20)  Press the [PAUSE] key. 
< 3 > A D J U S T    S E T 
 
R B N    A D J    < F W >    - 1 0
 
             (21)  Ribbon motor drive voltage fine adjustment 
(Take-up): 
  Set a fine adjustment value using the [FEED] 
and [RESTART] keys....