Toshiba B Sa4t G Manual

 
- 98 - (2) Test print for assembly process 
     
Power OFF   (1)  Power off state 
             
        [FEED] [PAUSE] (2)  While holding the [FEED] and [PAUSE] keys 
down, turn the power on.   
< 1 > D I A G .       V 1 . 2 A
             (3)  The self-test menu is displayed. 
              
        [FEED] 
 
(4)  Press the [FEED] key. 
< 2 > P A R A M E T E R    S E T
 
             
 (5)  System mode menu display 
 (Parameter setting) 
              
        [FEED] 
 
(6)  Press the [FEED] key. 
<...

 
- 99 -  
< 4 > T E S T    P R I N T 
             (19)  System mode menu display 
(Test print) 
              
        [PAUSE] 
 (20)  Press the [PAUSE] key. 
< 4 > T E S T    P R I N T 
A U T O    P R I N T ( T R A N )(21)  Assembly process automatic print mode 
(Transmissive sensor) 
             
        
[PAUSE] (22)  Press the [PAUSE] key. 
    One label is fed. 
3-dot slant line: 5 labels are printed. 
< 4 > T E S T    P R I N T 
A U T O    P R I N T ( T R A N )(23)  Assembly process automatic...

 
- 100 - 6.5.2  Details of Test Print Setting   
(1)  Test print mode 
 • PRINT CONDITION (Test print condition parameters) 
  •  SLANT LINE(1DOT)  (1-dot slant line print) 
  •  SLANT LINE(3DOT)  (3-dot slant line print) 
 • CHARACTERS (Character print) 
  •  BARCODE  (Bar code print) 
 • NON-PRINTING (Nothing prints.) 
  •  FACTORY TEST  (Line print for assembly process) 
 • AUTO PRINT(TRAN) (Assembly process automatic 
print/transmissive sensor) 
  •  AUTO PRINT(REFL)  (Assembly process automatic...

 
- 101 - (5) Sensor (SENSOR) 
  
  •  NONE  (No sensors used) 
 • REFLECT. (Reflective sensor) 
 • TRANS. (Transmissive sensor) 
 
 
 
(6)  Print type (PRT TYPE) 
 
 • TRANSFR (Thermal transfer) 
 • DIRECT (Direct thermal) 
 
 
 
(7)  Issue type (TYPE) 
  
  •  [S] NO CUT  (Batch issue mode) 
  •  [C] WITH CUT  (Cut issue mode) 
  •  [H] PEEL OFF  (Strip issue mode) 
 
 
(8)  Label length (LABEL LEN.) 
  •  999  (Label length: 999 mm) 
  •  998  (Label length: 998 mm) 
  •  997  (Label length: 997 mm)...

 
- 102 - (10)  Parameter values after the power is turned off and on again 
  •  Menu selection:  Test print condition parameter setting 
  •  Issue count (ISSUE COUNT):  1 
  •  Print speed (PRINT SPEED):  4 ips   
 • Sensor (SENSOR): Transmissive sensor 
  •  Print type (PRT TYPE):  Thermal transfer print mode 
  •  Issue type (TYPE):  Batch issue 
  •  Label length (LABEL LEN.):  76 mm 
  •  Paper feed (PAPER):  Paper feed is performed. 
(11) Supplementary explanations 
  •  When the [FEED] and...

 
- 103 -   •  Enlarged view of slant lines 
    1-dot slant line print (Print ratio: 16.7%)
 
  
 
 
 
 
 
    3-dot slant line print (Print ratio: 16.7%)
 
  
 
 
 
 
 
  

 
- 104 - 6.5.3  Test Print Samples 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  1-dot slant line print   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  3-dot slant line print 
 
 
  

 
- 105 -  
 
  Character print (203 dpi) 
 
 
 
Character print (300 dpi) 
  

 
- 106 -
 
 
 
Character print (Chinese 203 dpi)  
*Supported by C2.0D or later 
 
 
 
 
Character print (Chinese 300 dpi)  
*Supported by C2.0D or later  

 
- 107 - 
 
  Bar code print (203 dpi) 
 
 
Bar code print (300 dpi)