Toshiba B Sa4t G Manual

 
- 138 -  
 
AUTO UNLOCK OFF 
AUTO UNLOCK ON 
RESTART
FEED 
RESTART
FEED 
to the next settingPAUSE PAUSE 
PASSWORD OFF ---- 
PASSWORD ON 0000 
RESTART
FEED 
RESTART FEED 
PAUSE 
PASSWORD ON 0000 
PASSWORD    2000
PASSWORD    E000
PAUSE 
PASSWORD    0000 
PASSWORD    0002
PASSWORD    000E
PAUSE 
Set a 4-digit password to protect the error tag 
detection setting from unauthorized changes.  
PAUSE 
RESTART
FEED
FEED
RESTARTRESTART 
FEED 
FEED 
RESTART 
RESTART
FEED
FEED
RESTARTRESTART 
FEED 
FEED 
RESTART...

 
- 139 - (6)  Maximum number of issue retries 
 
 
 
 
 
 
  0 to 255 
  Set a maximum number of retries to issue an RFID tag. 
When issuing an RFID tag failed, the printer prints the error pattern, and retries to issue the 
tag for up to specified number of times.   If the printer does not succeed even after having 
retried for the max. times, the printer stops, resulting in an error. 
 
(7)  Maximum number of read retries 
 
 
 
 
 
 
 
  0 to 255 
  Set a maximum number of retries to read an RFID...

 
- 140 - (9)  Maximum number of write retries 
 
 
 
 
 
 
 
  0 to 255 
Set the maximum number of retries to write data onto an RFID tag.   
The printer retries to write data onto an RFID tag for up to specified number of times.    If the 
timeout period expired before the max. number of retries have been done, the printer stops 
the retries at the time. 
 
 
(10)  Write retry time-out 
 
 
 
 
 
 
 
  0.0 to 9.9 (0.0 seconds to 9.9 seconds) 
Set the timeout period during which RFID tag write retries...

 
- 141 - (12)  Radio output power level: When the B-SA704-RFID-U2-EU-R is used.   
 
 
 
 
 
 
 
  9 to 18 
Set the power level of the RFID module.   
When the value is “9”, the power is the weakest, and when “18”, the power is the strongest.   
The factory default setting is “18”.    The optimum value differs depending on the tag types.   
Usually, it is not necessary to change this value but changing the value may be able to 
improve the read/write rate. 
 
(13) AGC threshold   
 
 
 
 
 
 
 
  0 to...

 
- 142 - (16)  AGC threshold for data write   
 
 
 
 
 
 
 
  0 to 15 
When the Q value is set to 1 or greater, the AGC threshold for data write becomes effective.   
When the obtained gain of an RFID tag is lower than the AGC threshold for data write, a 
data write operation is not performed.    In other words, setting an AGC threshold for data 
write enables writing data only to a tag placed just above the antenna.   
Supposing that the gain of a tag just above the antenna is 14 and that of a tag off...

 
- 143 - Example 2
 
AGC threshold for data write: 11 
Lower limit for retry: 9 
Detected tag’s gain: 8 
As the gain of the tag is lower than the threshold, a data write operation is not performed for 
this tag at the first try.    Also, the gain is lower than the lower limit. 
Then the printer retries to write data to this tag according to a new AGC threshold of 9.     
In this case, a retry of data write will mostly fail because the detected tag’s gain is lower than 
the new threshold.    (However,...

 
- 144 -
6.12  Z-MODE SETTING (SUPPORTED FROM C1.9A) 
6.12.1  Z-Mode Setting Operation Example 
 
 
 
 
 
< 1 > D I A G .        C 1 . 9 A
           
 
 
< 2 > P A R A M E T E R S E T
           
 
 
< 3 > A D J U S T    S E T
           
 
 
< 4 > T E S T    P R I N T
           
 
 
< 5 > S E N S O R    A D J .
           
 
 
< 6 > R A M   C L E A R
           
 
 
< 7 > I P    A D D R E S S
           
 
 
< 8 > B A S I C       
           
 
 
< 9 > F O R   F A C T O R Y
           
 
[FEED]...

 
- 145 -  
< 1 0 > R F I D       
           
 
 
< 1 1 > Z - M O D E   
           
 
 
< 1 1 > Z - M O D E   
O F F         
 
 
< 1 1 > Z - M O D E   
O N    S E T T I N G    O F F
 
 
< 1 1 > Z - M O D E   
O N    S E T T I N G    O N
 
 
(Display of the BASIC system mode program)
 
 
 
< 1 1 > Z - M  O D E   
           
 
 
When the Z-MODE is enabled. 
 
 
 
 
(Display of the BASIC system mode program)
 
[FEED]
[RESTART]
[PAUSE] 
[RESTART]
[PAUSE]
 
(2) Turn on the printer power.   
(27) The...

 
- 146 - Z-Mode Setting (Z-Mode) 
 
 • OFF Disabled 
  •  ON SETTING OFF  Z-Mode is enabled, but the BASIC system mode 
program is not enabled. 
  •  ON SETTING ON  Both Z-Mode and BASIC system mode program 
are enabled. 
 
NOTE: For details, refer to Section 5.15 Z-MODE SETTING. 
 
 
 
FEED 
RESTART 

 
- 147 -
7. DOWNLOAD MODE 
 
     
Power OFF   (1)  Power off state 
              
        
        [FEED]+[PAUSE]+ 
[RESTART] (2)  Turn the power on by pressing the [FEED], 
[RESTART] and [PAUSE] keys at the same 
time. 
D O W N L O A D   M O D E 
             (3)  Download mode display 
              
        [FEED] 
 (4)  Press the [FEED] key. 
D O W N L O A D   M O D E  2
             (5)  Download mode 2 display 
              
        [PAUSE] 
 (6)  Press the [PAUSE] key. 
D O W N L O A D   M O D...