Tone Commander 40d120 Installation Instructions

13-102633 Rev. HPage 41
Tone Commander 40d120 Installation Instructions
®
Figure 8– 40d Console Default Key Assignments, Siemens National ISDN
Siemens
National ISDN 

Page 4213-102633 Rev. H
Tone Commander 40d120 Installation Instructions
®
1611171218131914110151111
2
621272228232924210252112
3
631373238333934310353113
4
641474248434944410454114
5
651575258535954510555115
6
661676268636964610656116
7
671777278737974710757117
8
681878288838984810858118
9
691979298939994910959119
10
7020803090401005011060120
Figure 9– 120d DSS Key NumbersAdd120to all numbers for 120d console #2,
240for 120d #3,360for 120d #4....

Configuration Sheet Preparation
The configuration sheets attached to the back of this manual (starting on page 133) should be filled in with
the setup information for this installation. Instructions for each configuration sheet table, and sample
configuration sheets, are included in this chapter. Sample information is printed in
italic block
font
.Please leave a copy of the configuration sheets on site.
System Setup

Press the MAINT key to enter Maintenance Mode.

Select SETUP.
The Setup menu will be...

40d120 Configuration Sheet #1
SPID and PDN Numbers
40d
SPID
(3-20 digits maximum;
exactly 10 digits for Lucent
Custom ISDN)42534910000101
PDN
(10 digits required for
proper operation)4253491000
ISDN Version
(check one)

Lucent National ISDN

Lucent Custom ISDN

Nortel National ISDN

Siemens National ISDN
120d SPID
120d #1
Keys 001-06042534911000101
Keys 061-12042534911010101
120d #2Keys 001-06042534920000101
Keys 061-12042534920010101
120d #3Keys 001-06042534930000101
Keys 061-12042534930010101
120d...

Selecting the Console

Select SPID from the Setup menu.
The SPID menu for the 40d console will be displayed.

NEXT and LAST display SPID information for 120d consoles in the system.
If a 120d is connected to the 40d console but not “installed”, “120d Unit #1: Not Installed” or
“120d Unit #2: Not Installed” is displayed depending on the number of 120d consoles being used.
If a 120d is connected to the 40d console and is “installed”, “120d Unit #1: Rev. x.xx” or “120d
Unit #2: Rev. x.xx” with the...

Adding (Installing) 120d Consoles

Select ADD from the SPID menu.
“>>> PRESS ANY Key ON 120d Unit #x 

Key Mapping
Most call processing functions can be assigned to any 40d key. All keys except the MAINT, VOL, SHIFT,
and Hold Loop keys are programmable. Available key assignments are listed below.
NOTE– Ring Delay and network features must be assigned to buttons with indicator lamps.
Key Type of Key Supplementary Info Required
Answer Local Function
Call Back
‡Network Feature Enter 2-digit Automatic Callback Feature Activator
Call Forward Network Feature Enter 2-digit Call Forward Variable Feature...

Configuration Sheet
Fill out Configuration Sheet #2 (page 134) with key locations, network button numbers, and dial access
numbers.

Select KEYS from the Setup menu.

Key assignments can be restored to the factory defaults as shown on pages 38-41 by selecting
RESET.

Press the key to be programmed.
The display will show the current key assignment.

Select EDIT to change the key function.
The key editing menu will be displayed.

Select the key function with the arrow keys.

If the selected function is a...

Call Forward Key
Voice Mail Key
The Voice Mail key has an optional NUMBER TO DIAL field. If the voice mail system has a common dialup
access number, enter it here, including any access pauses and common dial codes required by the system.
Allowable entries are digits0-9,#,*, andP(a pause; press dial pad key 7 twice to enter).
The display will show the number being entered. The character position will not
advance
automatically – use the arrow keys.
The firstPin the dial string causes the console to dial...

Intercom Keys
Up to four keys may be designated as intercom keys. Intercom calls are originated by pressing an intercom
key. Incoming calls to an intercom call appearance are queued for answering, as with other calls.
Network Call and Network Feature Keys
These options are used for generic network features that are not predefined in the console.


Network Call automatically initiates a call before sending the Feature Activation code.


Network Feature sends a Feature Activation code independent of call...