Home > Tone Commander > Telephone > Tone Commander 40d120 Installation Instructions

Tone Commander 40d120 Installation Instructions

Here you can view all the pages of manual Tone Commander 40d120 Installation Instructions. The Tone Commander manuals for Telephone are available online for free. You can easily download all the documents as PDF.

Page 31

Console Assembly
40d
120d
13-102633 Rev. HPage 31
Tone Commander 40d120 Installation Instructions
Figure 1
1. Install the handset cradle on the 40d console
using the screws provided. The cradle is
usually installed on the left side, near the
handset jack, but may be installed on either
side of the console.
2. Plug the handset’s cord into the jack beneath
the front left edge of the console.
3. Use the supplied printed keycap labels or type
feature names on blank labels. Place the labels
beneath the clear...

Page 32

Console Connections
120d Data Connection
In addition to the power and telco connection explained below, each 120d console requires one data
connection to the 40d or adjacent 120d console.
Refer to Figure on page 34.
1. 120d #1
– plug the supplied 4 conductor modular cord into the nearest “DSS” jack on the 40d
console.
If installing a second, third, or fourth 120d console, plug the supplied modular cord into the unused
“DSS” jack on the preceding 120d.
2. Plug the other end into either “DSS” jack on the...

Page 33

Power and Telco Connection (one per 40d or 120d console)
Each power supply can power three 40d and/or 120d consoles. Use an additional power supply if the
attendant position has three or four 120d DSS consoles.
Power supplies may be installed at the console location or in a remote equipment room.
Refer to Figure on page 34.
1. Plug a supplied 8 conductor modular cord into the telco ISDN U-interface jack.
2. Plug the other end into a “LINE” jack on the power supply.
3. Plug the second supplied 8 conductor...

Page 34

Page 3413-102633 Rev. H
Tone Commander 40d120 Installation Instructions
Figure 4–Typical Installation 

Page 35

System Programming
Several network interface and operation parameters are programmable by the installer, allowing
compatibility with a wide variety of central office features. The system is pre-programmed at the factory;
many installations will require few changes to these values. Programming is retained in the 40d’s memory
when power is disconnected. A parameter or feature may be altered at any time without reprogramming the
entire system.
The PC-based Setup Utility provided with the 40d120 offers a...

Page 36

Password Protection
To prevent inadvertent or unauthorized changes to console programming, you can enable password
protection. Passwords consist of four digits entered with the dial pad or the Setup Utility. Three separate
passwords are provided:
Mode Default Password
Console Setup 7743 (SPID)
Name/Autodial 6263 (NAME)
Statistics Reset 7828 (STAT)
When passwords are enabled, the console will prompt for a password whenever a user attempts to access
one of the above programming modes.
Enter the password...

Page 37

Enter the new password with the dial pad.
Select NEXT, then enter the new password again for confirmation.
Select DONE to enable the new password.
Default Passwords
The default passwords listed in the table above are reloaded whenever the password mode is changed
from disabled to enabled.
Use this procedure if you forget a custom password.
Set option switch 2 OFF.
Cycle power to disable all passwords.
Set option switch 2 ON.
Cycle power again to enable default passwords.
13-102633 Rev. HPage 37...

Page 38

Page 3813-102633 Rev. H
Tone Commander 40d120 Installation Instructions
Lucent
National ISDN
®
123456
Figure 5– 40d Console Default Key Assignments, Lucent National ISDN 

Page 39

13-102633 Rev. HPage 39
Tone Commander 40d120 Installation Instructions
®
Figure 6– 40d Console Default Key Assignments, Lucent Custom ISDN
Lucent
Custom ISDN 

Page 40

Page 4013-102633 Rev. H
Tone Commander 40d120 Installation Instructions
®
CALL FWD57
Figure 7– 40d Console Default Key Assignments, Nortel National ISDN
Nortel
National ISDN 
Start reading Tone Commander 40d120 Installation Instructions

Related Manuals for Tone Commander 40d120 Installation Instructions

All Tone Commander manuals