Tone Commander 40d120 Installation Instructions

							Console Assembly
40d
120d
13-102633 Rev. HPage 31
Tone Commander 40d120 Installation Instructions
Figure 1
1. Install the handset cradle on the 40d console
using the screws provided. The cradle is
usually installed on the left side, near the
handset jack, but may be installed on either
side of the console.
2. Plug the handset’s cord into the jack beneath
the front left edge of the console.
3. Use the supplied printed keycap labels or type
feature names on blank labels. Place the labels
beneath the clear plastic keycaps, then snap
the keycaps onto the keys.
(bottom view)
handset
jack
Figure 2
1. Fasten the console tie bracket beneath the left
edge of the 120d console using the supplied
mounting screws.
2. Fasten the other end of the tie bracket beneath
the right edge of the 40d console using the
supplied mounting screws.
3. If the attendant position has two 120d
consoles, attach the second 120d console to
the first in the same manner.
4. Fill out the keycap labels with station names or
numbers (refer to the configuration sheets).
Place the labels beneath the clear plastic key
caps, then snap the keycaps onto the DSS
keys.(bottom view)
120d
40d 
						

							Console Connections
120d Data Connection
In addition to the power and telco connection explained below, each 120d console requires one data
connection to the 40d or adjacent 120d console.
Refer to Figure on page 34.
1. 120d #1
– plug the supplied 4 conductor modular cord into the nearest “DSS” jack on the 40d
console.
If installing a second, third, or fourth 120d console, plug the supplied modular cord into the unused
“DSS” jack on the preceding 120d.
2. Plug the other end into either “DSS” jack on the 120d console (second 120d if applicable).
Page 3213-102633 Rev. H
Tone Commander 40d120 Installation Instructions
MONRUN
DSS
Line/Power
(U)RS-232
Serial
PortProgramming
SwitchOption
Switches for
testing
onlyDSS
1
(DH )2
(DL)3
(DL)4
(DH)
DSS
1
(PS+)2
(PS-)3
(N/C)4
(TIP)5
(RING)6
(N/C)7
(PS-)8
(PS+)
Line/Power
(U)
Figure 3– 40d and 120d Console Rear Panel 
						

							Power and Telco Connection (one per 40d or 120d console)
Each power supply can power three 40d and/or 120d consoles. Use an additional power supply if the
attendant position has three or four 120d DSS consoles.
Power supplies may be installed at the console location or in a remote equipment room.
Refer to Figure on page 34.
1. Plug a supplied 8 conductor modular cord into the telco ISDN U-interface jack.
2. Plug the other end into a “LINE” jack on the power supply.
3. Plug the second supplied 8 conductor modular cord into the matching “CONSOLE” jack on the
power supply.
4. Plug the other end into the “LINE/POWER” jack on the console rear panel.
5. When ready to test the system, plug the power supply into a standard 120 VAC, 60 Hz outlet.
13-102633 Rev. HPage 33
Tone Commander 40d120 Installation Instructions
Use only the Tone Commander 40d120 Power Supply (model #102612)
with the following ratings:
120 VAC @60 Hz
POWER 
						

							Page 3413-102633 Rev. H
Tone Commander 40d120 Installation Instructions
Figure 4–Typical Installation 
						

							System Programming
Several network interface and operation parameters are programmable by the installer, allowing
compatibility with a wide variety of central office features. The system is pre-programmed at the factory;
many installations will require few changes to these values. Programming is retained in the 40d’s memory
when power is disconnected. A parameter or feature may be altered at any time without reprogramming the
entire system.
The PC-based Setup Utility provided with the 40d120 offers a user interface that simplifies setup and
name/number entry. Please refer to the 40d120 Setup Utility User’s Guide
, doc. #14-280177, that
accompanies the utility diskette.
All setup information may also be entered using only the console keys, by placing the console in
Maintenance Mode as explained in this section. The following features may be accessed from Maintenance
Mode:
1.System Setup Parameters: SPID numbers, Key assignments, Call queues, Recall timers, Call
processing loop modes
2.Name/Autodial Database
3.Time of Day Clock Setting
4.System Usage Statistics
5.System Diagnostics
Using Maintenance Mode
The Maintenance Mode must be entered prior to attempting any of the following programming procedures.
Enter this mode only when the console is idle, i.e., no calls are in progress or on hold.
ToenterMaintenance Mode:

Press the MAINT key.
The display will indicate that Maintenance Mode has been entered. Name programming, time
setting, system statistics, system setup, or Maintenance Mode exit may be selected with the Hold
Loop keys.
Normal key and display operations are suspended. The console will continue to ring and place
incoming calls in queue.
In maintenance mode, the six hold loop keys directly below the display act as “soft” function keys.
Key functions are identified in the bottom line of the display.
ToexitMaintenance Mode and store all programming:


Press the Hold Loop key associated with EXIT or DONE from any programming screen until the main
menu is displayed, then select EXIT from the main menu.
Normal key and display operations will resume. The main menu will be displayed the next time
the MAINT key is pressed.
or


Press the MAINT key.
Normal key and display operations will resume. The last-used menu will be displayed the next
time the MAINT key is pressed. This allows you to answer a call, then resume programming
where you left off.
13-102633 Rev. HPage 35
Tone Commander 40d120 Installation Instructions
MAINTENANCE MAIN MENU
NAMES TIME STATS SETUP DIAG EXIT 
						

							Password Protection
To prevent inadvertent or unauthorized changes to console programming, you can enable password
protection. Passwords consist of four digits entered with the dial pad or the Setup Utility. Three separate
passwords are provided:
Mode Default Password
Console Setup 7743 (SPID)
Name/Autodial 6263 (NAME)
Statistics Reset 7828 (STAT)
When passwords are enabled, the console will prompt for a password whenever a user attempts to access
one of the above programming modes.

Enter the password digits with the dial pad when the Enter Password prompt appears.
Asterisks are displayed to hide the entered password.

Select DONE.
Enabling/Disabling Passwords
To enable passwords, set option switch 2 ON, then power up the console. If the console is already powered
up, disconnect power for a few seconds.
Setting option switch 2 OFF, then cycling console power, disables passwords.
Changing Passwords
You can change any of the passwords. All passwords must consist of four digits.


Passwords must be enabled.


Enter Console Setup (page 43), Name/Autodial Programming (page 62), or Statistics Reset (page 67)
mode.
The Enter Password prompt for the selected mode is displayed.


At the Enter Password prompt, enter the current password with the dial pad.
If you don’t know the password, restore the defaults - see Default Passwords below.


Select CHANGE to change the password for the mode shown in the upper right of the display.
Page 3613-102633 Rev. H
Tone Commander 40d120 Installation Instructions
[SETUP]
Enter Password: ****
CHANGEABORT DONE
[SETUP]
Enter Password: ****
CHANGE ABORTDONE 
						

							
Enter the new password with the dial pad.

Select NEXT, then enter the new password again for confirmation.

Select DONE to enable the new password.
Default Passwords
The default passwords listed in the table above are reloaded whenever the password mode is changed
from disabled to enabled.
Use this procedure if you forget a custom password.

Set option switch 2 OFF.

Cycle power to disable all passwords.

Set option switch 2 ON.

Cycle power again to enable default passwords.
13-102633 Rev. HPage 37
Tone Commander 40d120 Installation Instructions
[SETUP]
Enter New Password: ****
ReEnter New Password: ****
NEXT DELETE ABORTDONE 
						

							Page 3813-102633 Rev. H
Tone Commander 40d120 Installation Instructions
Lucent
National ISDN
®
123456
Figure 5– 40d Console Default Key Assignments, Lucent National ISDN 
						

							13-102633 Rev. HPage 39
Tone Commander 40d120 Installation Instructions
®
Figure 6– 40d Console Default Key Assignments, Lucent Custom ISDN
Lucent
Custom ISDN 
						

							Page 4013-102633 Rev. H
Tone Commander 40d120 Installation Instructions
®
CALL FWD57
Figure 7– 40d Console Default Key Assignments, Nortel National ISDN
Nortel
National ISDN