Tone Commander 40d120 Installation Instructions

							13-102633 Rev. HPage 41
Tone Commander 40d120 Installation Instructions
®
Figure 8– 40d Console Default Key Assignments, Siemens National ISDN
Siemens
National ISDN 
						

							Page 4213-102633 Rev. H
Tone Commander 40d120 Installation Instructions
®
1611171218131914110151111
2
621272228232924210252112
3
631373238333934310353113
4
641474248434944410454114
5
651575258535954510555115
6
661676268636964610656116
7
671777278737974710757117
8
681878288838984810858118
9
691979298939994910959119
10
7020803090401005011060120
Figure 9– 120d DSS Key NumbersAdd120to all numbers for 120d console #2,
240for 120d #3,360for 120d #4. Key positions 61-120 are
accessed by first pressing the
SHIFT key on the 40d console. 
						

							Configuration Sheet Preparation
The configuration sheets attached to the back of this manual (starting on page 133) should be filled in with
the setup information for this installation. Instructions for each configuration sheet table, and sample
configuration sheets, are included in this chapter. Sample information is printed in
italic block
font
.Please leave a copy of the configuration sheets on site.
System Setup

Press the MAINT key to enter Maintenance Mode.

Select SETUP.
The Setup menu will be displayed.
SPID, PDN, and C.O. Switch Type
Lucent Custom ISDN lines may be configured for either multipoint or point-to-point operation. Multipoint
lines can have multiple terminal devices connected to the same ISDN line. Point-to-point lines can have
only one terminal device connected to the line.National ISDN lines are always multipoint.
The 40d may be connected to either a point-to-point or multipoint ISDN line. A 120d console configured for
60 stations may use either a point-to-point or multipoint line; a multipoint line configuration is required for
120 stations.
Consoles must be programmed with 10-digitServiceProfileIdentifier (SPID) numbers obtained from your
local telephone company. The SPID uniquely identifies the console when it is connected to the network.
The 40d has one SPID. Each 120d may have one or two SPIDs; two are required for more than 60
stations. In this application, the 120d appears as two distinct ISDN terminals to the network, each having
60 call appearances.
Additionally, the 40d console must be programmed with aPrimaryDirectoryNumber (PDN).
Configuration Sheet
Fill out Configuration Sheet #1 (page 133) with the PDN for the 40d console, and SPID numbers for the
40d and all 120d consoles. Check the appropriate ISDN Version box.
13-102633 Rev. HPage 43
Tone Commander 40d120 Installation Instructions
MAINTENANCE MAIN MENU
NAMES TIME STATSSETUPDIAG EXIT
[SETUP]
SPID KEYS QUEUE TIMER LOOPS EXIT
National ISDNFor National ISDN lines, the SPID format should consist of your 10-digit PDN
(Including area code), followed by “0101”.
Lucent
Custom ISDNFor Custom ISDN lines, the SPID format should consist of “01” + the 7-digit
PDN (excluding area code) + “0”.
IMPORTANT– Although a SPID number is not required for a point-to-point ISDN line, failure to enter one
for the 40d will not allow it to initialize. Contact your service provider if the SPID format does not work. 
						

							40d120 Configuration Sheet #1
SPID and PDN Numbers
40d
SPID
(3-20 digits maximum;
exactly 10 digits for Lucent
Custom ISDN)42534910000101
PDN
(10 digits required for
proper operation)4253491000
ISDN Version
(check one)

Lucent National ISDN

Lucent Custom ISDN

Nortel National ISDN

Siemens National ISDN
120d SPID
120d #1
Keys 001-06042534911000101
Keys 061-12042534911010101
120d #2Keys 001-06042534920000101
Keys 061-12042534920010101
120d #3Keys 001-06042534930000101
Keys 061-12042534930010101
120d #4Keys 001-06042534940000101
Keys 061-12042534940010101
Page 4413-102633 Rev. H
Tone Commander 40d120 Installation Instructions 
						

							Selecting the Console

Select SPID from the Setup menu.
The SPID menu for the 40d console will be displayed.

NEXT and LAST display SPID information for 120d consoles in the system.
If a 120d is connected to the 40d console but not “installed”, “120d Unit #1: Not Installed” or
“120d Unit #2: Not Installed” is displayed depending on the number of 120d consoles being used.
If a 120d is connected to the 40d console and is “installed”, “120d Unit #1: Rev. x.xx” or “120d
Unit #2: Rev. x.xx” with the programmed SPID number is displayed.
Entering/Editing SPID & PDN, Selecting Switch Type
This option is not available for 120d consoles that are displayed as “Not Installed” – see Adding (Installing)
120d Consolesbelow.

Select EDIT from the SPID menu.
The SPID/PDN/Switch editing screen for the selected console will be displayed.

The blinking cursor will be in the SPID field initially. Using the dial pad, enter the SPID as assigned by
the telco.
Overwrite desired digits where necessary, or select DELETE to delete your choice of a single
character (CHAR), all characters in a field (FIELD). The arrow keys move the cursor position in a
field.


(40d only) – Select NEXT to move to the PDN field. Enter the PDN for the selected console.


(40d only) – Select NEXT to move to the SWITCH field. Press either arrow key until the correct C.O.
switch type for this installation is displayed.


Select DONE to store changes and return to the SPID menu.
or
Select ABORT to restore the previous settings and return to the SPID menu.
13-102633 Rev. HPage 45
Tone Commander 40d120 Installation Instructions
40d: S/W 2.11 H/W 1.23 [SPID]
SPID:
PDN: SWITCH: NORTEL NI-1
NEXT LAST EDIT EXIT
40d: S/W 2.11 H/W 1.23 [EDIT]
SPID: 42534910000101
PDN: 4253491000 SWITCH: ATT NI
NEXT  DELETE ABORT DONE 
						

							Adding (Installing) 120d Consoles

Select ADD from the SPID menu.
“>>> PRESS ANY Key ON 120d Unit #x 
						

							Key Mapping
Most call processing functions can be assigned to any 40d key. All keys except the MAINT, VOL, SHIFT,
and Hold Loop keys are programmable. Available key assignments are listed below.
NOTE– Ring Delay and network features must be assigned to buttons with indicator lamps.
Key Type of Key Supplementary Info Required
Answer Local Function
Call Back
‡Network Feature Enter 2-digit Automatic Callback Feature Activator
Call Forward Network Feature Enter 2-digit Call Forward Variable Feature Activator
(+ destination number
*)
Park Network Feature Enter 2-digit Directed Call Park Feature Activator
Cancel Local Function
Conference Network Feature Enter 2-digit Conference Feature Activator (typically 60)
*
Connect Network Feature Enter 2-digit Transfer Feature Activator (typically 61)*
Drop Network Feature Enter 2-digit Drop Feature Activator (typically 62)*
Hold Local Function
Inspect
‡Network Feature Enter 2-digit Inspect Feature Activator
Intercom 1-4 Network Feature Enter 2-digit Intercom Feature Activator
‡or Call Appearance*
Network Call Network Feature Enter 2-digit Feature Activator
Network
FeatureNetwork Feature Enter 2-digit Feature Activator
Originate Local Function
Page Local Function Enter Paging DN (15 digits max.)
Pickup Network Feature Enter 2-digit Directed Call Pickup Feature Activator
Poll Local Function
Priority Call
‡Network Feature Enter 2-digit Dial Call Waiting Feature Activator
Release Local Function
Ring Delay
On/OffLocal Function
Split Local Function
Time/Date
‡Network Feature Enter 2-digit Time/Date Feature Activator
Unpark Network Feature Enter 2-digit Call Park Answer Back
‡or Call Park Retrieve *
Feature Activator
Voice Mail 1-2 Local Function Enter Voice Mail DN (15 digits max.)
* National ISDN ‡ Lucent Custom ISDN
13-102633 Rev. HPage 47
Tone Commander 40d120 Installation Instructions
National ISDNWith National ISDN, Feature Activation (button) numbers must be assigned for
Conference, Connect (Transfer), and Drop keys. These keys are preassigned
when the console is configured for Lucent Custom ISDN – see page 39.
Siemens
National ISDNThe Connect key should be programmed with the Conference feature
activator (typically 60) for Siemens National ISDN. 
						

							Configuration Sheet
Fill out Configuration Sheet #2 (page 134) with key locations, network button numbers, and dial access
numbers.

Select KEYS from the Setup menu.

Key assignments can be restored to the factory defaults as shown on pages 38-41 by selecting
RESET.

Press the key to be programmed.
The display will show the current key assignment.

Select EDIT to change the key function.
The key editing menu will be displayed.

Select the key function with the arrow keys.

If the selected function is a network feature, “NEXT” will be displayed. Select NEXT, then enter the
network button number with the dial pad.
DELETE allows you to delete individual characters or an entire field. A delete operation may be
canceled by selecting ABORT.

Select DONE to store changes for this key.
or
Select ABORT to cancel any changes.

You will be returned to the key selection menu. Select another key.
or
Select EXIT to return to the Setup menu.
Page Key
The Page key requires a NUMBER TO DIAL entry. Enter the directory number for the dialup paging
system, up to 15 digits.
Page 4813-102633 Rev. H
Tone Commander 40d120 Installation Instructions
FUNCTION: Pickup [EDIT]
NETWORK BUTTON: 58
NEXT  DELETE ABORT DONE
FUNCTION: Page [EDIT]
NUMBER TO DIAL:2852743
NEXT  DELETE ABORT DONE 
						

							Call Forward Key
Voice Mail Key
The Voice Mail key has an optional NUMBER TO DIAL field. If the voice mail system has a common dialup
access number, enter it here, including any access pauses and common dial codes required by the system.
Allowable entries are digits0-9,#,*, andP(a pause; press dial pad key 7 twice to enter).
The display will show the number being entered. The character position will not
advance
automatically – use the arrow keys.
The firstPin the dial string causes the console to dial all digits preceding theP, then wait for the voice mail
system to answer. SubsequentPentries pause dialing for 1 second. The digits in a DSS key’s VM entry (7
maximum) are appended to the Voice Mail key’s dial string (24 maximum). If the Voice Mail key dial string
contains aP, the DSS key digits are dialed after the voice mail system answers; otherwise, digits from both
keys are dialed after the DSS key is pressed.

If all voice mailboxes share the same dialing prefix, program the Voice Mail key with these common
digits. This can be used to overcome the DSS key’s 7-digit VM limitation.

Voice mailbox numbers may be dialed with the dial pad if the NUMBER TO DIAL entry ends with aP.

Leave the Voice Mail NUMBER TO DIAL field blank
if each voice mailbox has a unique directory
number, i.e., no common prefix or dialup number.
Two keys can be configured as Voice Mail keys, to accommodate two voice mail systems with different
access numbers.
13-102633 Rev. HPage 49
Tone Commander 40d120 Installation Instructions
Enter only the call forward button number for Lucent Custom ISDN.
To set the forward-to number, exit Maintenance Mode. Press the ORIGINATE
key. Enter the network code used to set the forward-to number. When you hear a
new dial tone, enter the forward-to number.Lucent
Custom ISDN
FUNCTION: Voice Mail 1 [EDIT]
NUMBER TO DIAL:3486725P
NEXT  DELETE ABORT DONE
FUNCTION: Call Forward [EDIT]
NETWORK BUTTON:57
FORWARD NUMBER:8273502
NEXT  DELETE ABORT DONE
With National ISDN, in addition to the network feature code, a forward-to number
(18 digits maximum) must be entered in the FORWARD NUMBER field.National ISDN 
						

							Intercom Keys
Up to four keys may be designated as intercom keys. Intercom calls are originated by pressing an intercom
key. Incoming calls to an intercom call appearance are queued for answering, as with other calls.
Network Call and Network Feature Keys
These options are used for generic network features that are not predefined in the console.


Network Call automatically initiates a call before sending the Feature Activation code.


Network Feature sends a Feature Activation code independent of call state.
Enter the Feature Activation code for the desired network feature in the NETWORK BUTTON field.
Page 5013-102633 Rev. H
Tone Commander 40d120 Installation Instructions
Intercom calls with Custom ISDN are originated on any originating or
nonreserved call appearance by sending a Feature Activation (button) number.
Program each intercom key with the Feature Activation number for the intercom
group.Lucent
Custom ISDN
FUNCTION: ICMÂ1 [EDIT]
NETWORK BUTTON:61
NEXT  DELETE ABORT DONE
FUNCTION: Ntwk Call [EDIT]
NETWORK BUTTON:64
NEXT  DELETE ABORT DONE
FUNCTION: Network Feature [EDIT]
NETWORK BUTTON:64
NEXT  DELETE ABORT DONE
FUNCTION: ICMÂ1 [EDIT]
CALL APPEARANCE:12
NEXT  DELETE ABORT DONE
With National ISDN, each intercom key has an associated call appearance. The
call appearance must be set up for intercom use at the central office.National ISDN