TiE Onyx 2, 3, 4, 5 Service And Programming Manual

Q-  WIDE PROGRAMMING
QO- 
 INTERCEPTS, BUSY INTERCEPT
Description
Related
Programming
Instructions
Step  
Step  
Step  
Use this option to   Intercept system-wide for DID trunks.
If 
 enable this option (Y). the  routes a DID call for a  or DND
extension to the attendant. If   this option (N). the DID caller hears
 instead.
Refer to the Direct 
 Dialing feature (Busy Intercept) for more
information.
None
 
Busy Intercept disabled (N).
None
To enter data on the PRF:
For QO- Busy on Table 10, enter Y or...

Q- SYSTEM WIDE 
QO- DID INTERCEPTS.  INTERCEPT
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step  l
Step  l
Use this option to enable/disable Rin,O-No-Answer Intercept system-wide for
DID trunks. If  enable this option (Y). unanswered DID calls ring the
attendant. If 
 disable this option  unanswered calls ring the destination
extension 
 the DID caller hangs up.
Refer to the Direct 
 Dialing feature (Ring-No-Answer Intercept) for
more information.
Conditions
None
Default...

Q- SYSTEM WIDE PROGRAMMING
QO- DID CAMP-ON TO BUSY 
Description
Related
Programming
Feature Reference
Instructions
Step  l
Step  l
Step 2 
Use this option to  Camp-On for DID calls to busy  If
you enable this option 
 a DID call Camps-On to a   If you
disable this option (N). a DID call to a busy 
 follows the Busy Intercept
routing.
Refer to the Direct 
 Dialing feature  Camp-On) for more
information. This option is not available in ONYX IV.
Conditions
None
Default 
DID Camp-On to   enabled (Y).
None...

Q- SYSTEM WIDE PROGRAMMING
QP- VOICE MAIL, ACD MAILBOX ACCESS DIGIT (ONYX IV)
Description
Use this option to designate the leading digit required to access the mailbox
that provides the ACD announcements. The system sends this digit to the
Voice Mail before sending the mailbox number. Some Voice Mail systems
require a # as the leading digit. Other Voice Mail systems don’t require- any
leading digit. This option lets you tailor the system to the requirements of the
connected Voice Mail.
This option only...

Q- SYSTEM WIDE PROGRAMMING
   ACD  ACCESS DIGIT (ONYX IV)
Issue 1-O
 For  Notes 
SOFTWARE CONFIGURATION2-3  

Q- SYSTEM WIDE PROGRAMMING
QP- VOICE MAIL, MAILBOX INSTALLED
Description
Related
Programming
l
l
l
l
l
l
l
Feature Reference
Instructions
Step 1 l
Step 1 l
Step 2 l
 3 l
Use this option to tell the system when a Voice Messaging System is
connected. Enable this option 
 if the system has a Voice Messaging
System. Disable this option 
 if the system does not have a Voice 
Messaging System.
Conditions
As soon as you enable QP, the system rings the Voice Mail ports.
Default Value
Voice Messaging System not...

Q- SYSTEM WIDE PROGRAMMING
QP- VOICE MAIL, VOICE MESSAGING MASTER EXTENSION
Description
Related
Programming
l
l
l
l
Feature Reference
Instructions
Step 1 
Step 1 l
Step 2 
Use this option to designate the Voice Messaging System master extension
number. The extension you select must be one of the Voice Messaging
System ports. Program the master number and designate VX ports before
assigning this option. See Related Programming below.
Conditions
None
Default Value
VX master number not programmed (300)....

Q- SYSTEM  
QQ-  PREFIX REQUIRED FOR  
Description
Use this option to indicate if the system is in a conflict area. A conflict area
has conflict codes. Conflict codes are area codes 
 212) that can-also be
local exchange codes. You enable QQ if 
  in a conflict area.
When you enable QQ (Y). users must dial 1 when dialing the conflict code as
an area code. Users omit the 
  dialing the conflict code as a local
exchange. You disable QQ if the system is not in a conflict area. If you
disable 
 the system...

Q- SYSTEM WIDE PROGRAMMING
QR- SIDE TONE TEST DIGIT
Description
Related
Programming
Feature Reference
Instructions
Step 1 l
Step 1 l
Step 2 
Step 3 
Issue 1-O
Use this option to designate the digit used for the side tone test. This test
adjusts the side tone level for each trunk. When you initiate the test-(by using
the IS option), the system:
o Seizes the trunk you specify for testing
o Outputs the side tone test 
 onto the trunk
o Listens for the side tone level
 Automatically adjusts the side tone...

Q- SYSTEM  
QS- INSTALL PRINTED CIRCUIT 
QS- INSTALL  
Description
Related
Programming
Feature Reference
Instructions
Step  l
Step  
Step  
Step 3 l
Step  l
In the large systems. this option is  INSTALL PRINTED CIRCUIT BOARDS.
Use this option to specify line and trunk  as installed (Y) or not installed
(N). A line or trunk PCB 
 function only if the system knows it is installed.
If 
 remove a line or trunk PCB from service. the trunks associated with it
no longer function. For 
 and 72x180 systems. use...