TiE Onyx 2, 3, 4, 5 Service And Programming Manual

Q- SYSTEM WIDE PROGRAMMING
 TROUBLE REPORT TELEPHONE NUMBER
Description
Use this option to designate the off-site service center’s telephone number (up
to 24 digits). This is the number the system calls to report a major alarm
(fault). Valid entries are O-9. 
  and P (pause)‘.
 ted
Programming
Feature Reference
If the  center is  or  the system immediately redials it
three more times. If the 
 report still cannot go through. the system
repeats the procedure 
 five minutes until successful.
If the 
 PCB...

Q- SYSTEM  
  REPORT  
instructions
Step I 
Step 1 l
Step  
Step 3 
To enter data on the PRF:
For 
 Tel  (2-I   on Table  enter the Trouble 
Telephone 
To enter data at the programming terminal:
   see: 
Type V. You see: TEL  (24 DGTS MAX)
Enter the  Trouble Report Telephone Number from Table 10 and press
RETURN.
If the  number is  digits long you don’t have to press RETURN.
To 
 a number.  
 1-O 

Q- SYSTEM WIDE PROGRAMMING
  AUTHORIZATION CODES
Description
Use 
this option to enter Automatic Route Selection (ARS) Authorization
Codes into the system. If 
  has ARS installed, it   these
codes. Each code 
can be from l-10 digits long, using any  of
digits O-9. Refer to the Automatic Route Selection feature and Appendix A
for more 
information.
 allows 64 ARS Authorization Codes. Large systems allow 184. This
option does not apply to key systems.
Conditions
None
Default 
No codes entered.
Related...

Q- SYSTEM  PROGRAMMING
 SUPPRESS   SPEED 
Description
Programming
Feature Reference
Instructions
Step 1 
Step 1 
Step  
Step 3 
Use this option to  the system from outdialing the  digit when
stored in a Speed Dial bin.
 prevented. the system stops dialing at  
The system does not dial the  or  digits after the  If allowed. the system
 the contents of the Speed Dial bin normally. This option also affects
numbers outdialed using:
 Automatic Route Selection
  Compatible Feature Keys
 Last Number Redial...

Q- SYSTEM WIDE 
 SINGLE DIGIT LINE ACCESS
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step  
Step  
Step  
Issue 1-O .Use this option 
  users the capability of accessing trunk group 1
(code 90) 
 d I’  9. If  enable  option  users cannot dial-access
trunk groups 
 If  disable this option. users can access any trunk
group by dialing 
the two digit code (90-98). Refer to the Line (Trunk)
Rotaries feature 
for more information on trunk groups. In systems with ARS,
enabling this...

Q- SYSTEM WIDE 
  SETUP,  REPORT PRINT 
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step  
Step  l
Step 3 l
Step  
Use this option to set the Traffic Management Report (TMS) print modes.
You can have the 
 report print  (using the HE or HF options) or
at a preset time. If 
 request automatic  the report can include
trunk data. trunk and operator data or all data. The options are:
0 Manual (using the HE or HF options)
1Automatic (at a preset time) for trunk data only. The data...

Q- SYSTEM WIDE PROGRAMMING
  SETUP, TMS PRINT TIMES SETUP
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Use this option to set the times that the TMS report should print. The data
clears after each time the report runs.
You can 
 set this option if you have
entered:
1-3 for QZ- TMS Report Print Modes
 Y for QZ-  Print Times Setup
You can have the TMS report print every hour or every combination of hours.
Conditions
None
Default Value
N for each hour OO:OO-23:00 (TMS report is not...

Q- SYSTEM  
      
Instructions
To enter data at the programming terminal:
Step  After entering 1. 2. 3 for QZ-  Report Print Modes. you see: SET UP 
PRINT TIMES?
Step  To change the  Report print times. enter Y. You see: PRINT TMS
DATA AT OO:OO?
Go to  
OR
 To leave the  Report print times unchanged, enter N. You see: SMDR
FOR TOLL CALLS ONLY?
Go to QZ-   for Toll Calls.
Step 3 lIf you want the  report to print at  hours (12 midnight), enter Y.
 see: PRINT TMS DATA AT 01 :OO?
OR
If  don’t want the TMS...

Q- SYSTEM W-IDE PROGRAMMING
  SETUP,  ONLY FOR TOLL CALLS
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step  
Step 2 
Use this option to have the SMDR report include all outside calls or just toll
calls. If you enter N. the 
 report includes all outside calls. If you enter
Y. the SMDR report includes just toll calls. The system defines toll calls as
follows:
  NNX + nnnn
NPA + 
 + nnnn
  NPA    nnnn
0 + NNX + nnnn
0  NPA + NNX  nnnn
Conditions
None
Default Value
N (SMDR for all...

Q-   
QZ-   INBOUND 
Description
Related
Programming
l
Feature Reference
Instructions
Step 1 
Step 1 
Step  
Use this option to  the SMDR report include or exclude incoming trunk
calls. If you enter Y. the report includes 
 outgoing trunk calls.
If you enter N. the SMDR report prints 
  trunk calls.
Conditions
None
Default 
 (SMDR report includes both incoming and outgoing trunk calls)
Station 
 Detail Recording
P- Print 
 Report  Print the SMDR report. The system can clear or
retain records from the...