TiE Onyx 2, 3, 4, 5 Service And Programming Manual

Q-   
 MUSIC/RELAY  EST  AUDIBLE LINE
Description
Related
Programming
l
l
l
l
l
l
In the large  use this option to assign the trunk number the system
 use to broadcast All Call  and  Audible. You  use the
trunk circuit 
  for  other purpose. Refer to the system
  for additional installation details. This option is
independent of the 
 Relay Control options.
 VS. this option is EXTERNAL  AUDIBLE. Enter  to enable
All Call Paging and Night Audible on the main CEU PA terminals. Enter
N(o) to disable Paging...

Q- SYSTEM WIDE PROGRAMMING
QM- MUSIC/RELAY CONTROL, ENT PAGE/NIGHT AUDIBLE LINE
Related
Programming
(Cont’d)
l
Feature Reference
Instructions
Step I l
 1 l
Step 2 l
Tenant Service. Assigning  Paging Zones to Tenants
E- Extensions, El- Circuit   Program the ports used for External
Paging as uninstalled (circuit type X). There are a total of four ports available
for External Paging.
  and  Control. Page Zone n Line Number (except in VS)
 Assign a trunk port for External Paging zones 1-3.  Call Paging also...

Q- SYSTEM WIDE PROGRAMMING
  CONTROL, INHIBIT AUDIBLE RING
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step  
Step  l
Use this option to enable/disable audible ring on the trunk port you designate
in QM- Est 
 Audible Line Number. If enabled (N), night 
can occur over the trunk port. If disabled (Y). night audible cannot occur.
Conditions
None
Default 
Audible ring enabled (N).
 Answer. Universal Night Answer
E- Extensions. ED- Trunk Control, 
 Control  An extension allows
UNA...

Q- SYSTEM WIDE 
QM- MUSIC/RELAY CONTROL,   n LINE 
Description
Related
Programming
l
l
l
l
. 
l
Use this option to assign the trunk circuits the system will use for external
Paging zones 
You should assign a different trunk for each of the three
zones. You cannot use the trunk circuits you designate here for any other
purpose. (Note that All Call Paging also broadcasts over these trunks.) Refer
to the system 
  for additional installation details. This option
is independent of the QM- Relay Control...

Q-  WIDE PROGRAMMING
 MUSIC/RELAY  PAGE ZONE  LINE NUMBER
Related
Programming
l
l
Feature Reference
Instructions
Step  
Step 
Step  
Step 3 
Step  l
  and Relay Control, Relay Control-Page On  on  
If enabled and Pageowner is main attendant (port OO/extension 300). relay
closes each time a user makes an All Call  announcement. If disabled
or Pageowner is other than the attendant. relay never closes for Paging.
  and  Control, Relay Control-Pageowner (Owner in 
  the  for ringer and page control. This...

Q- SYSTEM  
  CONTROL. EXTERNAL   ONLY)
Description
Related
Programming
l
l
l
Use this option to  External Paging on the expansion CEU PA
terminals. 
 enabled (Y).  Paging zone 1 and All Call broadcast over
the expansion 
 PA terminals. If disabled (N), paging does not broadcast
 the espansion   PA  terminals. Refer to the system Hardware Manual
for 
 installation details.
This option only applies to VS.
Conditions
External Paging uses the fourth trunk circuit on the first CO Module in each
CEU. You...

Q- SYSTEM WIDE PROGRAMMING
   EXTERNAL PAGE  ONLY)
Feature Reference
Instructions
Step  l
Step I l
Step  
Issue 1-O
  and Relay Control.  Control-Pageouner (Owner in 
 Assign the  for ringer and page control. This assignment should
be the attendant in each tenant group.
Paging
Tenant Service
To enter data on the PRF:
For QM- External Page on Table 10. Y(es) or N(o).
To enter data at the programming terminal:
After programming QM- Inhibit Audible Ring, you see: 
EXTERNAL PAGE
PORTS, EXTERNAL PAGE
Enter...

Q-  WIDE 
 MUSIC/RELAY CONTROL,  ON EXTERNAL PAGE ZONES
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step I 
Step 2 
Use this option to  Background Music to play over the External
Paging zones. If 
  BGM  play over all the external zones (All
Call and    are idle.  disallowed. BGM will not  Refer to
the svstem 
 Manual and the Background Music feature for
 information on Background Music.
Always make a “test” page after enabling this option.
Default 
BGM will not play over...

Q-  WIDE PROGRAMMING
  CONTROL, INTERRUPTED RING RELAYS
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step  
Step 2 
Issue 1-O .Use this option to enable/disable interrupted closure for the external relays
when used for ringing. If enabled 
  pulse one second closed/three
seconds open when activated. If disabled 
 relays have continuous closure
when activated. This option affects all the external relays. All external relays
are normally open.
Conditions
None
Default Value
Relays...

Q-   PROGRAMMING
  CONTROL.   MUSIC GAIN
Description
Note:
Related
Programming
l
Use this option to adjust thegain for the Background  that  over
the External 
 ports.
The adjustment you make  this option does not
affect the 
  internal Background  You can make fine
adjustments to internal and 
   separately. The choices
are:
-l’dB loss
-6 
 loss
-3 
 loss
0 
  gain
  gain
This option 
 appears if  enter Y fo
Zones.
 QM- BGM on Extema Page
A 3 
 gain   doubles the BGM volume on the external port. A 3...