TiE Onyx 2, 3, 4, 5 Service And Programming Manual

Q- SYSTEM  PROGRAMMING
QL-  CODES, SERVICE LINE NUMBERS
Description
Related
Programming
l
l
l
Use this option to assign the trunk  master number for each of the
rotaries used  ARS. LCR. Service number 01 should be the DDD trunk
group. This entry should correspond to the EA- First Trunk in Group entry.
 you are programming  this is the last QL option you have to program.
If 
you are programming LCR.  must enter additional data for:
QL- COS Needed to Access 
 Route
QL- Type of Service
QL- Access Code
QL-...

Q- SYSTEM WIDE 
QL-  CODES.  LINE 
Related
Feature Reference
Instructions
Step 1 l
Step  l
Step 3 
QL-  Codes,  Code  For dial-up services. enter
the access code (telephone number) for the service.
QL- 
 Codes,  Code  For dial-up services, enter
the security code the service requires.
Automatic Route Selection
Least Cost Routing
To enter data on the PRF:
For QL- Service nn Line Number? on Table 10, enter the master number for
each of the 
 trunk rotaries.
To 
enter data at the programming terminal:
After...

Q- SYSTEM WIDE PROGRAMMING
QL- 
 CODES, COS NEEDED TO ACCESS ALT ROUTE
Description
Related
Programming
l
l
l
l
Use this option to set the minimum COS (00-27) LCR requires before routing
a call to the alternate route. This can occur only if 
 primary route is busy.
If you enter 10. for esample. extensions 
 a COS of 00-10 can  the
alternate route. Extensions 
 a COS of  cannot use the alternate
route. If you enter 27. all classes of service can use the alternate route.
This option only applies to systems...

 SYSTEM WIDE PROGRAMMING
QL- 
 CODES. TYPE OF 
Description
Related
Programming
l
l
l
l
l
Feature Reference
Use this option to enter the  of service (O-5) for each LCR  number
(trunk rotary). The choices are:
0 
1 FX Line
2 MCI. Tie line
3 Western Union
4Same as  (but does not strip the leading 1)
Same as  (but does not strip the leading 1)
This option only applies to systems with LCR installed. This option does not
apply to systems with ARS. This option does not apply to VS.
Conditions
None
Default...

Q- SYSTEM WIDE PROGRAMMING
QL- 
 CODES, TYPE OF SERVICE
Instructions
Step  
Step I l
Step  
Step 3 
Issue 1-O
To enter data on the PRF:
For QL- Type of 
on Table  enter the Service type for  LCR
service number (rrunk 
To enter data at the programming terminal:
After programming QL- COS Needed to Access 
 Route. you see: TYPE OF
SERVICE
Enter the type of service for service number 01 from Table 10.
  you enter service  0 or 1. you see: SERVICE 02 LINE NUMBER.
Go back    ice Line  and enter data for your...

Q- SYSTEM WIDE 
QL-  CODES, ACCESS CODE
Description
For 
 types 5.  this option to enter the service’s access code.
With dial-up MCI. for example. this would be the MCI local number. The
access code can be up to 11 digits ion consisting of the digits  and 
This option only applies to systems with LCR installed. This option does not
apply to systems 
 ARS. This option does not apply to VS.
None
Default Value
No code entered.
Related
Programming
l
l
l
l
Feature Reference
Instructions
Step 1 l
Step  l
Step...

Q- SYSTEM WIDE 
QL-  CODES, SECURITY CODE
Description
Related
Programming
l
Feature Reference
Instructions
Step  
Step  
Step  l
Issue 1-O
For service types  use this option to enter the service’s security code,
After dialing the access code. the caller must dial the security code before the
service will accept the call. The security code can be 
 to 9 digitslong.
consisting of the digits O-9. 
 and 
This option  applies to systems with LCR installed. This option does not
apply to systems 
  This option...

 SYSTEM WIDE PROGRAMMING
QM- MUSIC/RELAY CONTROL, BGM LINE NUMBER
Description
Related
Programming
l
Feature Reference
Instructions
Step 1 l
Step 1 l
Step  l
Step 3 l
In the large systems. use this option to designate the trunk circuit connected to
the Background Music music source (e.g.. 05). You cannot use the trunk
circuit you designate here for 
 other purpose. In VS, enter Y to enable
 Music;  to disable. Refer to the system Hardware Manual for
 installation details.
Conditions
In VS. Background...

Q- SYSTEM WIDE 
QM-  CONTROL, MOH LINE NUMBER
Description
Related
Programming
l
Feature Reference
Instructions
Step  l
Step 1 
Step  
Issue 1-O .
In the large systems. use this option to designate the trunk circuit connected to
the Music on Hold music source (e.g..02). YOU cannot use the trunk circuit
you designate here for any other purpose.
YOU can make the same entrv for
QM- MOH Line Number and 
 BGM Line Number, if desired. In 
enter Y to enable Music on Hold: N to disable. Refer to the system...

  x     
QM- MUSIC/RELAY CONTROL,  ON TRANSFER
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step  l
Step  l
Use this option to determine if transferred callers should hear Music on Hold
or 
 tone. If enabled (Y). transferred callers hear Music on Hold while
they wait for their call to go through. If disabled (N). transferred callers hear
 tone.
For this option to function.  must have:
lMusic on Hold installed (refer to the Music on Hold feature)
 Designated a trunk in QM-  Line...