TiE Onyx 2, 3, 4, 5 Service And Programming Manual

Q- SYSTEM WIDE 
  COSTROL. EXTERNAL PAGE  GAIN
Related
Programming
(Cont’d)
l
l
Feature Reference
Instructions
Step  l
Step  l
Step  l
Tenant Service, Assigning External Paging Zones to Tenants
E- 
Trunks,  Circuit Type  Program the ports used for External Paging as
uninstalled (circuit 
  There are a total of four ports available for
External Paging.
 hlusic and Relay Control, Est Page/Night Audible Line Number  In
the large systems. assign the trunk number the system will use to broadcast
All Call...

Q- SYSTEM WIDE 
 MUSIC/RELAY CONTROL, REL.l.Y  ON
Description
Related
Programming
l
l
Feature Reference
Instructions
Step 1 l
Step 1 l
Step  
Use this option to control   Mode ringing activates
external relays O-3. You program this option separatelv for each relay. Refer
to the system 
 Manual for instructions on connecting devices to the
relays. This option does not 
 to VS.
The relay activates for Night Mode calls if:
 QM- Ringer On is enabled (Y)
 QM- Page  entry is the main attendant (usually 300)...

Q- SYSTEM WIDE PROGRAMMING
 MUSIC/RELAY  RELAY CONTROL-PAGE ON
Description
Use this option to control 
 Paging activates external relays (O-3). You
program this option separately for each relay. Refer to the system Hardware
Manual for instructions on connecting devices to the relays. The system
assigns relays O-3 to Paging zones as follows:
This  for...
0All Call Paging
         All Call and  1 Paging
2
3:  :    : 
All Call and Zone 2 
All Call and Zone 3 Paging
The relay activates each time a user makes...

Q- SYSTEM WIDE 
QM-, MUSIC/RELAY CONTROL.  CONTROL-PAGE ON
l
l
l
l
Feature Reference
Instructions
Step 1 l
Step  l
Step  l
Paging. External
E- Trunks. 
 Circuit Type  Program the ports used for External Paging as
uninstalled (circuit 
 
  and Relay Control.   Audible Line   In
large systems. assign the trunk number the system will use to broadcast All
Call Paging and Night Audible. In VS. enter 
 to have All Call Page
broadcast over the main 
 P.4 terminals.
  and Relay Control. Page Zone n Line Number...

Q-  WIDE PROGRAMMING
 MUSIC/RELAY   CONTROL-PAGEOWNER
Description
Use this option to assign the 
 for ringer and Paging relay control, as
shown 
 You program this option separately for each of the  relays.
This option is OWNER in VS.
For ringing...
The relay activates for Night  calls if:
 QM- Ringer On is enabled 
 QM- Page  entry is the main attendant (usually 300)
The 
 activates uhen an extension rings if:
 QM- Ringer On is enabled 
 QM- Page Owner entry is the extension (not main attendant), trunk,...

Q- SYSTEM WIDE 
QM- MUSIC/RELAY CONTROL, RELAY 
Related
Programming
(Cont’d)
l
P
l
P
l
l
l
l
Feature ReferencePaging, Esternal
E- Trunks. 
 Circuit   Program the ports used for External Paging as
uninstalled (circuit type Xj.
  and  Control. Ext Page/Night Audible Line Number  In
large systems, assign the trunk number the system will use to broadcast All
Call Paging and Night Audible. In VS, enter Y to have All Call Page
broadcast over the main 
 PA terminals.
 hfusic and Relay Control. Page Zone n Line...

Q-   
    
Instructions
To enter data on the PRF:
step 
 For QM-     on Table  enter the pageowner’s 
number.The entry    an OPS. XCD  master or Ring Group number.
To enter data at the programming terminal:
Step  lAfter programming   Control-Page On for relay 0, you see: PAGE
OWNER
Step 
 lEnter the  for  Relay 0. Page Owner from Table 10 and press
RETURN. You see: RELAY 1. RINGER ON
Go to   Control-Ringer On for relay 1.
Issue 1-OSOFTWARE CONFIGURATION Z-309 

Q- SYSTEM WIDE PROGRAMMING
QN- RESTORE STANDARD PORT ASSIGNMENTS
Description
Use this option to restore (reinstate) the standard extension/trunk-to-port
assignments. This may come in handy if you want to restore the 
assignments in a heavily modified system. This option restores the 
port assignments only. It does not restore other programming.
Keep the following in mind when programming ports:
Use El- Port Number to change the extension/trunk assignment for a port.
Use HH- Port/Extension Checker to make...

Q- SYSTEM WIDE PROGRAMMING
QO- DID INTERCEPTS, ABSORB  DIGIT
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step 
Step 2 
Step 3 l
Issue 1-O
Use this option to  1st digit absorption system-wide for DID
trunks. If you enable this option (Y). the system is compatible with four-digit
DID service. 
 you disable QO- Absorb  Digit (N). the system is
compatible with three-digit DID service.
However. you can still use 
Absorb 1st Digit for DID and Tie Trunks (BYO:l) to enable digit...

Q- SYSTEM WIDE 
QO- DID INTERCEPTS, VACANT  INTERCEPT
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step 1 l
Step  l
Use this option to Vacant Number Intercept system-wide for
DID trunks. If you enable this option (Y). the system routes 
 or
partially dialed DID calls to the attendant. you disable this  a
partially or improperly dialed call does not go through.
Refer to the Direct 
 Dialing feature (Vacant Number Intercept) for
more information.
None
Default 
Vacant Number...