TiE Businesscom Plus Hardware Manual

INSTALLING OPTIONAL EQUIPMENT
--------------------------------
Audio
Source
Audio
 
outputI
Shielded Cable
M
C
B
M
C
B
B-LBR-A Box  
 
Amp Enable
(If required)
FIGURE 2-11 USING THE B-LBR-A PCB TO CONTROL AN AUDIO LOUD BELL
2-29 

INSTALLING OPTIONAL EQUIPMENT
Installing
 MusicThis section provides information on installing
 Background Music  in the BUSINESSCOM PLUS
System.
Specifications
BGM (all systems)
Input Impedance: 600 ohms
Input Level:
Nominal 250 
 
Maximum Input: 1 Vrms
BGM Installation,
BUSINESSCOM PLUS 
Refer to Figure 2-12 Installation  of  Background
Music,BUSINESSCOM PLUS 
1. Connect BGM source inputs to clips  of the
 Block.(If BGM source is also used as a source
for MOH,cross connect clips  to clips 45,
46,...

INSTALLING OPTIONAL EQUIPMENT
BGM Installation,
BUSINESSCOM PLUS
Refer to Figure 2-13 Installation  of  Background
Music,BUSINESSCOM PLUS 
1. Connect inputs from BGM source to clips  of
the 
 Block. If the BGM source is not used as a
source for MOH,proceed to step 3.
2. If BGM source is also used as  a source for MOH:
a.Overlap approximately four inches of wire, and
punch down the wire approximately four inches
from the end.
 Punch down overlap from wire connected at clip
21 to clip 9.
C.Punch down...

INSTALLING OPTIONAL EQUIPMENT
Installing External Music On Hold 
External MOH An external music source can serve as a substitute
for the internally-synthesized MOH that is available.
Specifications
BGM (all 
 Impedance: 600 ohms
Input Level:
Nominal 250  
Maximum Input: 1 Vrms
MOH Installation,
BUSINESSCOM PLUS 
Refer to Figure 2-14Installation of External Source
of Music On Hold,BUSINESSCOM PLUS 
1. Connect inputs from an external MOH source to clips
 on the  Block.
2. Move switch 2 on the 
 PCB in the...

INSTALLING OPTIONAL EQUIPMENT
MOH Installation,
BUSINESSCOM PLUS 
Refer to Figure 2-15Installation of External Source
of Music On Hold in a BUSINESSCOM PLUS 
1. Connect inputs from external MOH to clip  on
the 
 Block.
2. To select external MOH, move SW1 on the B-TSU-A
PCB to the opposite position of that marked 1.
(The 1 position is used to select internal MOH.)
3. Adjust the audio level of MOH with 
 on the
B-TSU-A PCB.
 Block
WHT-BLU
  To DSS 
To Door Chime Box
To External MOH Source
 2-15INSTALLATION...

INSTALLING OPTIONAL EQUIPMENT
Installing Music On Hold  Contacts
MOH Contacts, 
BUSINESSCOM PLUS 
This section provides information on installing an
external device to MOH Contacts.
The B-HBU-A PCB has
an auxiliary relay for MOH that is energized when a
call is placed on Hold.
The energized relay provides
a closure for control of an audio source.
Specifications
MOH Contacts
Current Rating:
1.25 amps for 24 VDC resistive loads
Installation
Refer to Figure 2-16
Music On Hold Contacts Wiring:
1. Connect...

INSTALLING OPTIONAL EQUIPMENT
Installing Paging Equipment
External Paging 
ContactsExternal zones have normally open contacts. If a
zone is activated,the contacts close. When a zone
receives BGM,the contacts become continually closed.
The relays for each zone are energized when Paging
amplifiers are in use,including CO audible and BGM
(if programmed).The relay is on the 
 PCB in
the BUSINESSCOM PLUS 
 The relays are on the
B-GCU-A PCB,a daughter board on the tone sender PCB
(B-TSU-A) in the BUSINESSCOM...

INSTALLING OPTIONAL EQUIPMENT
Installation
BUSINESSCOM 
 
Refer to Figure 2-18External Paging Contact Wiring,
BUSINESSCOM PLUS 
1. Connect wires to clips  on the  Block for
the first set of External Paging Contacts
2. Connect the other ends to the device.
3. Connect wires to clips 
 on the  Block for
the second set of External Paging Contacts, and
connect the other ends to the device.
 Block
To
ToDSS 1
DSS 2
To
To
ToDoor Chime Box 1
Door Chime Box 2
External MOH Source
ToMOH Contacts
To External Zone 1...

INSTALLING OPTIONAL EQUIPMENT
Installing External Paging Output
This section provides information on the installation
of external devices to the external zone(s). Each zone
can receive CO Audible,BGM, External Alarm Signals,
and Paging.Speakers can be used to broadcast these
signals at the zone.External page zones can be used
to provide talk-back paging.
SpecificationsOutput Impedance: 600 ohms
Output Level:
Nominal 250  
Maximum Output:400  RMS
Installation of
External Devices,
BUSINESSCOM PLUS 
Refer...

INSTALLING OPTIONAL EQUIPMENT
Installation of
External Devices,
BUSINESSCOM PLUS 
Refer to Figure 2-20,External Paging Output Wiring
on a BUSINESSCOM PLUS 
1. Connect wires from clips  on the  Block to
an amplifier for External Zone 1. The amplifier
inputs must match the specifications above. Attach
the speaker to your amplifier.
2. Connect wires from clips 
 on the  Block to
an amplifier for External Zone 2. The amplifier
inputs must match specifications above. Attach
the speaker to your amplifier.
3....