TiE Businesscom Plus Hardware Manual

SPECIFICATIONS
BUSINESSCOM PLUS 64 SPECIFICATIONS
GENERAL SPECIFICATIONS
System Capacity:
CO Lines:
24
Intercom Talkpaths: 6
Key Telephones:
64
Speakerphones:24
 Telephones:32
ELECTRICAL SPECIFICATIONS
Power Requirements:(AC supply must be dedicated)
KSU/Power Supply Operating Range:117 VAC 
 10%
60 Hz  1 Hz
Power Dissipation:
KSU/Power Supply Unit: 684 Watts 
 5.85 amps
2340 BTU/hr.
Grounding Requirements:
KSU ground lug,
14 AWG or larger copper wire to cold water pipe or
known good earth ground
Cable...

SPECIFICATIONS
I-4SPECIFICATIONS
BUSINESSCOM PLUS 64 SPECIFICATIONS 
MECHANICAL SPECIFICATIONS
Dimensions andWeights:
KSU 27.8 in.
71.3 cm
Power Supply13.3 in.
34.0 cm
Executive/Key
Telephone
Door Chime Box
3.1 in.
8.0 cm
5.1 in.
13.1 cm
DSS Console
2.0 in.
5.2 cm
X
X
X
X
X
X
X
X
X
X
ENVIRONMENTAL SPECIFICATIONS
26.1 in.
67.0 cm
19.0 in.
48.9 cm
8.0 i n .
20.5 cm
3.9 in.
9.9 cm
7.4 in.
18.9 cmX
X
X
X
X
X
X
X
X
X
Environmental Operating Conditions
Temperature:
KSU and Telephones: 0  t o  4 5  degrees C...

PART 2INSTALLATION
INSTALLATION
INTRODUCTIONThe INSTALLATION Section provides detailed procedures
for installing BUSINESSCOM PLUS Systems. This section
presents the system installation in five parts:
o PREPARING FOR INSTALLATION
shows how to select an installation site. It also
indicates the tools and test equipment needed to
install the system.
o INSTALLING THE KSU AND POWER SUPPLY
shows how to install, connect, and ground the
systems KSU and power supply. It tells how to
install a surge protector and...

PREPARING FOR INSTALLATION
Site
RequirementsMeeting and maintaining established environmental
standards maximizes the life of your system. Be sure
that the site you select for installing the KSU is:
o a clean, dry,and secure location.
o not accessible to unauthorized personnel
o free from static electricity (e.g., dry copiers)
and excessive vibration (e.g., heavy machinery)
o removed from caustic chemicals
o environment-controlled
This site must also comply with the standards out-
lined in the Bell...

PREPARING FOR INSTALLATION
Tools and
Test Equipment
The following tools, documentation, and test equip-
ment are required when you install the system:
0
0
0
0
0
0
0
0
0
0
0BUSINESSCOM PLUS Hardware Manual and  Guides
Volt/Ohm meter 
high input impedance
 tolerance of
Linemans test setaccuracy)
Punch down tool for cross connecting wires
Flatblade screwdriver
Grounded wrist strap
Work light or flashlight
Spare 
Marking pen/pencils to label blocks and cables
Drill for mounting equipment
Separate copies of...

PREPARING FOR INSTALLATION
Before installing the system, be sure to:
o Unpack all the telephone equipment.
o Compare the equipment received with a list of
equipment ordered.
o Check for any physical damage.
o Check that all components are on site.
o Verify that a building plan is complete and on
site.This plan should show the location and type
of telephone instrument, extension numbering, and
any special considerations.
Hanging the
BackboardReview the installation layout drawing (Figures 2-1
through 
and...

PREPARING FOR INSTALLATION
Jacks
Linesr-l
Power
 
 
Mounting
Brackets
BEFORE CONNECTING OR 
WARNING: FOR PROTECTION AGAINST
B2
Brackets
To Stations
10-17 
Optional
Equipment
IIDedicated
View
A
Power
 
 
0 
Surge AC
Protector OutletTo Stations
18-21 
Optional
Equipment
 2-l BUSINESSCOM PLUS  INSTALLATION LAYOUT
2-5 

PREPARING FOR INSTALLATION
FIGURE 2-2  24 KSU-B (P/N 15101)
2-6 

PREPARING FOR INSTALLATION
  
FIGURE 2-3 BUSINESSCOM 36 KSU-B (P/N 15201)
2-7 

PREPARING FOR INSTALLATION
 
FIGURE2-4 BUSINESSCOM 36 KSU-B (P/N 15201)
W/BUSINESSCOM 64 EXPANSION CABINET
(P/N 15301)