Tascam TM-D1000 Operations Manual

11 - MIDI Machine control
31  TASCAM TM-D1000 Operations Manual
11.6 Locating to a memory position
Locating to a memory position is done by holding 
down the 
SHIFT key and pressing the CH SEL key of 
the channel (location memory) to which you will be 
locating.
11.7 Editing a memory location
1Press the MEMO key so that the display 
shows 
MEMO Edit on the top line.
NOTE
If MIDI Timecode is currently being received 
at the 
MIDI IN jack, you must press the MEMO 
key twice to obtain the 
MEMO Edit mes-...

 TASCAM TM-D1000 Operations Manual 32
12 - MIDI control of the TM-D1000
Snapshot changes may be carried out from a MIDI 
controller as Program Change messages.
In addition, the two effect units and the four channel 
dynamic processor components of the TM-D1000 
may also be set up to respond to Program Change 
messages, each on their own channel, if desired.
12.1 Setting Program Change 
receive channels
1Press and hold down the SHIFT key and press 
the 
OPTION key.
2Turn the DATA ENTRY knob until the...

12 - MIDI control of the TM-D1000
33  TASCAM TM-D1000 Operations Manual
Unless otherwise stated, the 127 values available to a 
MIDI controller are interpreted and converted into 
the 100 parameter value steps used by the TM-
D1000.
12.4 System Exclusive parameters 
and data dumps
The TM-D1000 also provides you with data dump 
and loading facilities, so that snapshots, effect set-
tings, etc. may be stored in a MIDI data Þle and 
uploaded to the mixer in a future session. Please con-
sult the Reference...

 TASCAM TM-D1000 Operations Manual 34
13 - Options
A number of options are available for the TM-
D1000, as described here.
13.1 RM-D1000 rack mounting kit
The RM-D1000 rack mounting kit allows the TM-
D1000 to be mounted in 6U of rack space (in addi-
tion to space needed at the top for the connectors).
You should also ensure that the rack is well-venti-
lated, allowing air to circulate for cooling the heat 
sink of the TM-D1000.
1The wristpad below the faders should be 
unscrewed before mounting the...

13 - Options
35  TASCAM TM-D1000 Operations Manual
channels 1 + 2 and 5 + 6, they will also be routed to 
the TDIF-1 B channels with the same numbers.
If input channels are routed using the DIRECT OUT 
function, and the IF-TD1000 Digital I/O board is Þt-
ted, the input channels will be output to the TDIF-1 
B connector. It may also be selected to be output in 
parallel to both TDIF-1 connectors (
A and B) by 
selecting input channels 1Ð8 as the source for TDIF-
1 
A.
13.3 FX-D1000 Effect Board
The...

 TASCAM TM-D1000 Operations Manual 36
14 - Miscellaneous functions
These functions help you with various settings of the 
TM-D1000.
14.1 Footswitch (REMOTE CONT)
The footswitch connected to the rear of the TM-
D1000 can be used to step through the snapshot 
memories, either forwards or backwards. It can also 
be used to perform punch-in and punch-out opera-
tions on the unit controlled via MMC.
1Press and hold down the SHIFT key, and 
press the 
OPTION key.
2Turn the DATA ENTRY knob until the bot-
tom...

14 - Miscellaneous functions
37  TASCAM TM-D1000 Operations Manual
Have the battery replaced by your TASCAM 
distributor. Do not attempt to replace the bat-
tery by yourself.
You can also check the current battery level using the 
following procedure:
Option Monitor à System à 
Battery Check
If the displayed value falls below 2.7 volts, it is time 
to consider replacing the battery. 
We also, as noted above, suggest that you have the 
battery replaced every three years or so, in order to 
avoid possible...