Siemens Saturn Iie Epabx Installation Test Procedures Manual

SATURN IIE EPABX
Installation Test ProceduresA30808-X5130-B120-l-8928Issue 1, May 1986.
Tab!c A.03 Station Line Test fCnntinc)edl,
STEPPROCEDURE
\-----------I
STEPFROCEDUZZVERIFICATTIONIF VER!FiCATIONIS NOT OBTAINED’
7Place station under test on-hook.Ringing returned.
If ringing is not heard, switch the sta-
tion instrument to determine if it is
defective. If ringing is still not heard,
replace the associated subscriber line
PCB.
8Pick up handset to answer test tail.
9Verify that the test tone level is...

SATURN IIE EPABXA30808-X5130-B120-l-B928instaliation Test ProceduresIssue 1, May 1986
Wbtc 6.04 DTMF Pad Test
STEPPWO@EDWEVERIFICATIONIF VERIFICATIGNIS NOT OBTAINED
7Depress the DTMF keypad buttons inRecall dial tone ceases. After all theIf busy tone is returned at any time,
the following sequence:DTMFjteypad buttons are depressedeither the DTMF key pad buttons werein the sequence indicated, test tonedepressed in the wrong sequencetheFor 12-button phones: 1, 2, 3, 4, 5, 6,(1004Hz @ -16dBm) is returned...

SATURN IIE EPABXA30808-X5130-B120-l-8928Installation Test ProceduresIssue 1, May 1986
Table 6.05 Console Test (Continued)
:TE?PRCCEDUREVERIFICATIDNlF VERlFlCATlONIS NOT OBTAINED+
6Depress the console’s keypad buttonsAll digits dialed are displayed (ac-If proper verification is not obtained orin the following sequence: 1, 2, 3, 4,
cumulate).busy tone is returned at any time, the
5, 6, 7, 8, 9, 0, * and #.keypad buttons or console buttons
were depressed out of sequence, the
7Depress the console’s feature...

I-SATURN 
IIE EPABXA30808-X5130-8120-143928installation Test Procedures
Issue 1, May 1986
TRUNK GGOUPSTATUS
nnnnnnnn k(ALPHANUMERIC DISPLAY LNI;)
SOUlxiOESTIXATION00000000
li 18 19 20 21 22 23 24
ALERTCL1Figure 6.19 Attendant Console 
Keypad and Feature Button Depression Sequence 

SATURN IIE EPABXA30808-X5130-B120-l-6926Installation Test Procedures
Issue 1, May 1986
Table 6.06 Attendant Console Displayable Characters
ORDER
1.2.
3.
4.
5.
6.
7.
8.
9.10.
11.
12.13.14.15.
16.
17.
1819.20.2’:.
23:
24.
25.
26.
27.
28.
29. 30.
31.
32.CHARACTER
I I I I I I ! !;;;;,A!,;;;;
$$$$5$$$o/o o/o 010 o/o o/o o/o o/o %&&&&&&&&I I I  I I I I I
( ( ( ( ( ( ( () 1 1 1 1 1 1 1* l * * * l * *++++++++I I > 9 I 1 3 I- - - - - - - -
i i i i i i i i00000000
1 1 1 1 1 1 1 1
22222222
33333333
44444444...

I  .SATURN 
IIE EPABXA30808-X5130-B120-I-6928Installation Test ProceduresIssue 1, May 1986
Table 6.07 Siemcns Digital Telephone 
- DVAD Dutton TestNOTES: 1) If the system option flag TSTDIAG has 
been enabled in the data base or the Siemcns Digital Telephone under
test is classmarked with TSTAPP feature, the maintenance test phone is nbt required to enable or disable the
Apparatus Diagnostic routines; therefore, perform only steps 5 through 9.
2) If the system option flag TSTDIAG has been disabled in the...

I-SATURN 
HE EPABX
Installation Test ProceduresA30808-X5130-8120-1-8928Issue 1, May 1986
IS BUTTON
DYAD
26 BUTTON
DYAD
SEE NOTENOTE: These buttons do not
contain 
LEDs.SEE NOTE 
y/  
’I
Figure 6.20 Siemens DYAD Telephone Button Depression Sequence
6-21 

SATURN IIE EPABX
Installation Test ProceduresA30808-X5130-BlZO-l-8928Issue 1, May 1986
Table 6.06Siemcns Digital Telephone 
- JR-DYAD Button Test
NOTES: 1) If the system option flag TSTDIAG has been enabled in the data base or the Siemens Digital Telephone under
test is classmarked with TSTAPP feature, the maintenance test phone is ‘not required to enable or disable the
Apparatus Diagnostic routines; therefore, perform only steps‘5 through 9.
2) If the system option flag TSTDIAG has been disabled in the...

I-SATURN 
IIE EPABXA30808-X5130-B120-l-8928Installation Test ProceduresIssue 1, May 1986
NOTES:* These feature buttons are not testable.
Buttons 9 through 13 do not contain LEDs.Figure 6.21 Siemeno JR-DYAD Telephone Button Depression Sequence
6-23 

I  .I-SATURN 
IIE EPABXInstallation Test ProceduresA30808-X5130-B120-l-8928Issue 1, May 1986
Table 6.09 Siemens Digital Telephone 
-DYAD Display Test
NOTES: 1) If 
the system option flag TSTDIAG has been enabled in the data base or the Siemens Digital Telephone under
test is classmarked with TSTAPP feature, the maintenance test phone is not required to enable or disabie the
Apparatus Diagnostic routines; therefore, perform only steps 5 through 9.
2) If the system option flag TSTDIAG has been disabled in...