Siemens Saturn Iie Epabx Installation Test Procedures Manual

							SATURN IIE EPABX
Installation Test ProceduresA30808-X5130-B120-l-8928Issue 1, May 1986.
Tab!c A.03 Station Line Test fCnntinc)edl,
STEPPROCEDURE
\-----------I
STEPFROCEDUZZVERIFICATTIONIF VER!FiCATIONIS NOT OBTAINED’
7Place station under test on-hook.Ringing returned.
If ringing is not heard, switch the sta-
tion instrument to determine if it is
defective. If ringing is still not heard,
replace the associated subscriber line
PCB.
8Pick up handset to answer test tail.
9Verify that the test tone level is cor-Test tone (1004Hz @ -lGdBm) isIf the returned test tone level is weak,rect by using a TMS.returned.swap the instrument to determine if it
is defective If the test tone level in-
creases considerably, replace 
the s:a-tion instrument. If test tone level
remains weak, replace the associat-
ed subscriber line PCB (SLMA,
10Place station under test on-hoo!(.SLA16 or SLMD).None.
11If no additional Test routines are to beperformed, proceed as follows:
Place maintenance test phone Dial tone is returned.
off-boo!
						

							SATURN IIE EPABXA30808-X5130-B120-l-B928instaliation Test ProceduresIssue 1, May 1986
Wbtc 6.04 DTMF Pad Test
STEPPWO@EDWEVERIFICATIONIF VERIFICATIGNIS NOT OBTAINED
7Depress the DTMF keypad buttons inRecall dial tone ceases. After all theIf busy tone is returned at any time,
the following sequence:DTMFjteypad buttons are depressedeither the DTMF key pad buttons werein the sequence indicated, test tonedepressed in the wrong sequencetheFor 12-button phones: 1, 2, 3, 4, 5, 6,(1004Hz @ -16dBm) is returned forDTMF keypad of the station under test7, 8, 9, 0, 4 and #.one minute.is defective or the subscriber line cir-
cuit is defective.
For 16-button phones: A, B, C, D, 1,
2, 3, 4, 5, 6, 7, 8, 9, 0, 
* and #.To locate failure, retry test to verify thatthe keypad buttons were not
depressed out of sequence. If
problem persists, swap the station in-
strument to determine ii it is defective.If problem remains, replace the rp-propriate subscriber line PCB.
8F;Q;he level of test tone by usingIf the measured test tone is correct
but is weak, replace the station set.
If the measured tone is low, 
rep!acethe subscriber line PCB SLMA or
SLA16).
9Place DTMF station under test on-None.hook to terminate test.
10If no additional apparatus tests are to
be performed, proceed as foilows:
Place maintenance test phone Dial tone is returned.
off-hoo!(.
Dial the Diagnostic Test Access Code.Recall dial tone is returned.
Dial 2 to disable the Apparatus Tests.
None.Place maintenance test phone None.
on-hook.
Table 6.05 Console Test
NOTES: 1)If the system option flag TSTDIAG has been enabled in the data base, the maintenance test phone is not required
to enable and disable the Apparatus Test routines; therefore, perform only steps 5 through 9.
2) If the system option flag TSTDIAG has been 
disabted in the data base, the maintenance test phone is required
to enable and disable the Apparatus Test routines; therefore, perform the entire procedure (steps 1 through 10).
STEPPROCEDUREVERIFICATIONIF VERIFICATION
IS NO-i- OBTAINED
1Place maintenance test phone Dial tone is returned.
off-hook.
2Dial the Diagnostic Test Access Code.Recall dial tone is returned.
3Dial 3 to enable the Apparatus Tests.Confirmation tone is returned.
4Place maintenance test phone None.
on-hook.
5At the Console under test dial the At-Recall dial tone is returned. Also theIf reorder tone is returned, the Atten-tendant Console Test access codeaccess code is displayed momentar-dant Console Test routine is in use,
when the console is in an idle state.ily, then the display changes to CON- retry later.
SOLE TEST and all button 
LEDs are
extinguished.
6-16 
						

							SATURN IIE EPABXA30808-X5130-B120-l-8928Installation Test ProceduresIssue 1, May 1986
Table 6.05 Console Test (Continued)
:TE?PRCCEDUREVERIFICATIDNlF VERlFlCATlONIS NOT OBTAINED+
6Depress the console’s keypad buttonsAll digits dialed are displayed (ac-If proper verification is not obtained orin the following sequence: 1, 2, 3, 4,
cumulate).busy tone is returned at any time, the
5, 6, 7, 8, 9, 0, * and #.keypad buttons or console buttons
were depressed out of sequence, the
7Depress the console’s feature buttonsEach button LED lights whenconsole is defective, or PIMD circuitin the sequence shown in Figure 6.19.’depressed and extinguishes when theis defective. To isolate the failure, retrynext key is depressed.test to verify that the buttons were not
depressed out of sequence.
aAfter the last button in the sequenceGroups of eight of each of the display-If proper verificaiion is not obtained oris depressed, depress any consoleable characters are scrolled in the se-busy tone is returned again, replace
button to initiate the display test. Thequence shown in Table 6.06. Ai-ier theassociated PIMD PCB to verify
display can be suspended bylast character is displayed (underwhether the PIMD circuit or the con-depressing any key on the consolescore character), the display unit issole is defective. If proper verificaiion
and resumed in the same manner.cleared and the following 
LEDsis obtained, replace the associa?edmomentarily light then extinguish inPIMD PCB. If proper verification is notthe following sequence:obiained or busy tone is returned
again, replace the console.
a) TRUNK GROUP STATUS 1 
-b) 
%“RCEc) DESTINATION
d) ALERT
e) CW
9 MAJ ALM
g) MIN ALM
After the above indications are com-
pleted the 
fo!lowing indications occur:
Ringbeck tone is returned.
All 
LEDs on the display assemblyflash..
.After the above indications are com-
pleted the following indications occur:
Ringback tone is returned.
All 
LEDs on the display assembly
flash.
The audible alerting device sounds at
intervals.REMOVE HANDSET is displayed.
9Remove and reinsert handset assem-INSERT HANDSET is displayed while
bly to terminate test, or wait 30 se-handset is removed. After handset isconds for test timeout.reinserted, console returns to normaloperation.
10If no additional apparatus tests are to
be performed, proceed as follows:
Place maintenance test phone Dial tone is returned.
off-hook.
Dial the Diagnostic Test Access Code.Recall dial tone is returned.
Dial 2 to disable the Apparatus Tests.
None.Place maintenance test phone None.
on-hook.
6-17 
						

							I-SATURN 
IIE EPABXA30808-X5130-8120-143928installation Test Procedures
Issue 1, May 1986
TRUNK GGOUPSTATUS
nnnnnnnn k(ALPHANUMERIC DISPLAY LNI;)
SOUlxiOESTIXATION00000000
li 18 19 20 21 22 23 24
ALERTCL1Figure 6.19 Attendant Console 
Keypad and Feature Button Depression Sequence 
						

							SATURN IIE EPABXA30808-X5130-B120-l-6926Installation Test Procedures
Issue 1, May 1986
Table 6.06 Attendant Console Displayable Characters
ORDER
1.2.
3.
4.
5.
6.
7.
8.
9.10.
11.
12.13.14.15.
16.
17.
1819.20.2’:.
23:
24.
25.
26.
27.
28.
29. 30.
31.
32.CHARACTER
I I I I I I ! !;;;;,A!,;;;;
$$$$5$$$o/o o/o 010 o/o o/o o/o o/o %&&&&&&&&I I I  I I I I I
( ( ( ( ( ( ( () 1 1 1 1 1 1 1* l * * * l * *++++++++I I > 9 I 1 3 I- - - - - - - -
i i i i i i i i00000000
1 1 1 1 1 1 1 1
22222222
33333333
44444444
55555555 66666666
77777777
88888888
99999999
: : : : : : : :
; ; ; ; ; ; ; ;
(((((((CTPffSf=>S????????
OQOQ@@@@ORDER
CHARACTER
33.AAAAAAAA
34.BBBBBBBBcccccccc
ii:DDDDDDDD
37.EEEEEEEE
FFFFFFFF
:iGGGGGGGG40:HHHHHHHH41.I I I I I I I I42.JJJJJJJJ43.K K K K K K I< K44.LLLLLLLL45.MMMMMMMM46.NNNNNNNN47.0000000048.PPPPPPPP49.QQQQQQQQ50.RRRRRRRR51.ssssssss52.TTTTTTTT54. 53.vvvvvvvv uuuuuuuu
55.wwwwwwww56.xxxxxxxx2;YYYYYYYYzzzzzzzz
59:[ I [ 1 I 1 1 I60.61.\\\\)))\1 1 I I62.A A A A ,I> A A A63.----_---
6-19 
						

							I  .SATURN 
IIE EPABXA30808-X5130-B120-I-6928Installation Test ProceduresIssue 1, May 1986
Table 6.07 Siemcns Digital Telephone 
- DVAD Dutton TestNOTES: 1) If the system option flag TSTDIAG has 
been enabled in the data base or the Siemcns Digital Telephone under
test is classmarked with TSTAPP feature, the maintenance test phone is nbt required to enable or disable the
Apparatus Diagnostic routines; therefore, perform only steps 5 through 9.
2) If the system option flag TSTDIAG has been disabled in the data base or the Siemens Digital Telephone under
test is not classmarked with the TSTAPP feature. the maintenance test phone is required to enable or disable
the Apparatus Diagnostic routine?
s; therefore, perform the entire procedure (steps 1’ through 10).
STEP
1
2
3
4
5
6
7
8
9
10PROCEDURE. VERIFICATION
‘lace the maintenance test phone,ff-hook.
3ial the Diagnostic Test Access Code.
Iial 3 to enable the Apparatus Diag-lostic Tests.
‘lace maintenance test phonex+hook.
‘lace Siemens DYAD Telephone,ff-hook.
Dial the Siemens Digital Telephonerest Access Code.
Ieoress the Siemens DYAD Telc-&ne keypad buttons as, fo!lows: 1,3,3,4,5,6,7,8,9,0,*,i?.Depress the 
DYAD feature buttons in
the sequence shown in Figure 6.20
and according to the Siemens DYAD
Telephone model.Place Siemens DYAD Telephone un-Siemens DYAD Telephone returns to
der test on-hook to terminate test.normal operation.
If no additional Apparatus Diagnostic
Test routines are to be performed, pro-ceed as follows:
Place maintenance test phone
off-hook.Dial tone is returned.
Dial the Diagnostic Test Access code.Recall dial tone is returned.
Dial 2 to disable the Apparatus Diag-
nostic Test.
None.Place maintenance 
test phone on-hook.None.None.
Iial tone is returned.
qecall dial tone is returned.
>onfirmation tone is returned.
Uone.
Iial tone is returned.
secall dial tone is returned.
The access code is momentarily 
dis-f reorder tone is returned, the Sie-3layed, then the display unit and but-nens DYAD Telephone Button Test is
ton LEDs are extinguished.n use, try later.
Button 
LEDs light when depressed
and extinguish when the next button
is depressed.
After the last button is depressed, the
following indications occur:
Ringback tone is returned.
All button 
LEDs flash.
The audible alerting device sounds at
intervals.TEST COMPLETE is displayed.IF 
VERiFICATlONIS NOT OBTAINED
f proper verification is not obtained cr
xsy tone is returned at eny time,
either the keypad buttons cr featuiebuttons were depressed out of se-
quence, the DYAD Telephone is defac-tive, or the SLMD circuit is defective.
To isolate the failure, retry test to veri-
fy that the buttons were not depressed
Dut of sequence.
If proper verification is not obtained orbusy tone is returned again, replace
the Siemens DYAD Telephone under
test with a known good DYAD Tele-
phone and retry test. If proper verifi-
cation is not obtained or busy tone is
returned again, replace the SLMD
PCB.I
-
6-20 
						

							I-SATURN 
HE EPABX
Installation Test ProceduresA30808-X5130-8120-1-8928Issue 1, May 1986
IS BUTTON
DYAD
26 BUTTON
DYAD
SEE NOTENOTE: These buttons do not
contain 
LEDs.SEE NOTE 
y/  
’I
Figure 6.20 Siemens DYAD Telephone Button Depression Sequence
6-21 
						

							SATURN IIE EPABX
Installation Test ProceduresA30808-X5130-BlZO-l-8928Issue 1, May 1986
Table 6.06Siemcns Digital Telephone 
- JR-DYAD Button Test
NOTES: 1) If the system option flag TSTDIAG has been enabled in the data base or the Siemens Digital Telephone under
test is classmarked with TSTAPP feature, the maintenance test phone is ‘not required to enable or disable the
Apparatus Diagnostic routines; therefore, perform only steps‘5 through 9.
2) If the system option flag TSTDIAG has been disabled in the data base or the Siemens Digital Telephone under
test is not classmarked with the TSTAPP feature, the maintenance test phone is required to 
enab!e or disable
the Apparatus Diagnostic routines; therefore, perfcrm ihe entire procedure (steps 1 through i0).
STEPPROCEDUREVERIFICATIONIF VERIFICATION
IS NOT OBTAINED
1Place the maintenance test phoneDial tone is returned.
off-hook.
2Dial the Diagncstic Test Access Code.Recall dial tone is returned.
3Dial 3 to enable the Apparatus Diag-Confirmation tone is returned.
nostic Tests,
4Place maintenance test phone None.
on-hook.
5Place JR-DYAD Telephone off-hook.Dial tone is rereturned.
6Dial the Siemens Digital TelephoneRecall dial tone is returned.If reorder tone is returned, the Sie-Test Access Code.mens JR-DYAD Telephcne Button Testis in use, try later.
7Depress the Siemens JR-DYAD Tele-Ii proper verification is net obtainsd or
phone keypad buttons as, follows: 1,busy tone is returned at any iime,
2, 3, 4, 5, 6, 7, 8, 9, 0, 
* , #.either the keypad buttons or feature
buttons were depressed out of se-
8Depress the JR-DYAD feature buttonsButton LEDs light when depressedquence, the JR-DYAD Telephone isin the sequence shown in Figure 6.21.and extinguish when the next buttondefective, or the SLMD circuit is
is depressed.defective. To isolate the failure, retry
test to verify that the buttons were not
After the last button is depressed, thedepressed out of sequence.
following indications occur:
If proper verification is not obtained orRingbac!c tone is returned.busy tone is returned again, replace
All button 
LEDs flash.the Siemens JR-DYAD Telephone un-der test with a known good JR-DYAD
The audible alerting device sounds atTelephone and retry test. If proper
intervals.verification is not obtained or busy
tone is returned again, the SLMD cir-
cuit is defective and the 
SLMD PC6requires replacement.
9Place Siemens JR-DYAD TelephoneSiemens JR-DYAD Telephone returns
under test on-hook to terminate test.to normal operation.
10If no additional Apparatus DiagnosticTest routines are to be performed, pro-ceed as follows:
P&tokmaintenance test phone Dial tone is returned.
Dial the Diagnostic Test Access code.Recall dial tone is reiurned.
Dial 2 to disable the Apparatus 
Diag-None.nostic Test.
Place maintenance test phone None.
on-hook.
6-22 
						

							I-SATURN 
IIE EPABXA30808-X5130-B120-l-8928Installation Test ProceduresIssue 1, May 1986
NOTES:* These feature buttons are not testable.
Buttons 9 through 13 do not contain LEDs.Figure 6.21 Siemeno JR-DYAD Telephone Button Depression Sequence
6-23 
						

							I  .I-SATURN 
IIE EPABXInstallation Test ProceduresA30808-X5130-B120-l-8928Issue 1, May 1986
Table 6.09 Siemens Digital Telephone 
-DYAD Display Test
NOTES: 1) If 
the system option flag TSTDIAG has been enabled in the data base or the Siemens Digital Telephone under
test is classmarked with TSTAPP feature, the maintenance test phone is not required to enable or disabie the
Apparatus Diagnostic routines; therefore, perform only steps 5 through 9.
2) If the system option flag TSTDIAG has been disabled in the data base or the Siemens Digital Telephone under
test is not classmarked with the TSTAPP feature, the maintenance test phone is required to enable or disable
the Apparatus Diagnostic routines; therefore, perform the entire procedure (steps 1 through 10).
XEPPROCEDUREVERIFICATIONIF VERIFICATION
IS NOT OBTAINED
1Place maintenance test phone Dial tone is returned.
off-hook.
.
./ ;
2Dial the Diagnostic Test Access Code.Recall dial tone is returned.
3Dial 3 to enable the Apparatus Diag-Confirmation tone is returned.
nostic test.
4Place maintenance test phone None.
on-hcok.
5Place the Siemens Digital TelephoneDial tone returned.
under test off-hook.
GDial the Siemens Digital TelephoneRecall dial tone is returned. The Ac-If reorder tone is returned, the Sie-test access code.cess code is momentarily displayed,mens Digital Telephone Display Test
then the display unit clears.is being used, retry later.
7Depress any button in the SiemensGroups of 16 of each of the displaya-If verification is not obtained, eitherDigital Telephone under test to initiateble characters are scrolled in the se-the Siemens Digital Telephone or thetest.quence shown in Table 6.09. After theSLMD circuit is defective. Replace
last characier (underscore) is dis-Siemens Digital Telephone with a
(Note: The display test can be sus-played the following occurs:good one and retry test. If verification
pended any time by depressing anyis obtained, replace the Siemens 
Dig-button. The test can be resumed atRingback tone is returned.ital Telephone.any time in the same manner.)
All button 
LEDs flash and the audibleIf verification is still not obtained,
alerting device sounds at intervals.replace the SLMD PCS.
TEST COMPLETE is displayed.
8Place Siemens Digital Telephone on-hook to terminate test or wait 30 se-
conds for test timeout.
9If no additional Apparatus DiagnosticTests are to be performed, proceed asfollows:
Place maintenance test phone Dial tone returned.
off-hook.
Dial the Diagnostic Test Access Code.Recall dial tone is returned
Recall dial tone returned.
Dial 2 to disable the Apparatus Diag-
None.nostic Test.
Place maintenance test phone None.
on-hook.
G-24