Siemens Saturn Iie Epabx Installation Test Procedures Manual

							i  .I
SATURN 
IIE EPABXA30808-X5130-B120-l-6928Installation Test Procedures
Issue 1, May 1986
Table 6.10 Siemens Digital Telephone Displayable Characters
ORDERCHARACTER
ORDERCHARACTER
1.! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !33.AAAAAAAAAAAAAAAA
2.#P It It I, I, ,I 0 0 I, r, 0 I, 0 I, ,I I,34,BBBBBBBBBBBBBBBB3.#H#H#####,Y######35.cccccccccccccccc4.$ssssss$s$s$s$s$36.DDDDDDDDDDDDDDDD5.o/b 010 vo %%%% vo vo o/o %% o/o %% o/o
37.EEEEEEEEEEEEEEEE
6.&&&&&&&&&&.&&&&&&38.FFFFFFFFFFFFFFFF7.39.GGGGGGGGGGGGGGGG8.;;;;;;;;;1;;;;;;40.HHHHHHHHHHHHHHHH9.))))))))))))))I)41.I I I I I I I I I I I I I I I I10.****************42.JJJJJJJJJJJJJJJJ11.-I-+++++++++++++++43.KKKKKKKKKKKKKKKK12.0000000e00.0.0..44.LLLLLLLLLLLLLLLL13.---------------45.MMMMMMMMMMMMMMMM14.46.NNNNNNNNNNNNNNNN15.GE;;;;;;;;;;;47.000000000000000016.000000000000000048.PPPPPPPPPPPPPPPP17.111111111111111149.QQQQQQQQQQQQQQQQ18.222222222222222250.RRRRRRRRRRRRRRRR19.333333333333333351.ssssssssssssssss20.444444444444444452.TTTTTTTTTTTTTTTT21.555555555555555553.uuuuuuuuuuuuuuuu22.666666666666666654.vuvvvvuvvvvvuvvv23.777777777777777755.wwwwwwwwwwwwwwww24.888888888888888856.xxxxxxxxxxxxxxxx25.999999999999999957.YYYYYYYYYYYYYYYY26.. . . * . . . . . . . . . . . .
. . . . . . . . . . . . . . . .58.zzzzzzzzzzzzzzzz
27.. . . . . . . . . . . . . . . .28.~~~~t~~~~i~i~lii59.11 1 [ I [ [ [ 11 I[ [ [ [ [
GO.
29.\ \ \> \     \ \   \ :\ \ \========zz==30.ff~~~,,,,,,,,,,,61.11 1 I II 111111111162.AAAAAAAAAAAAAAAA31.????????????????63.-----___32.Q@Q@@@@@@@@Q@QOQ
6-25 
						

							SATURN IIE EPABX‘nstallation Test Procedures
Table 6.11 Outgoing Trunk TestA30808-X5130-8120-l-8928Issue 1, May 1986
STEP
1
5
6
7
8A
8BPROCEDURE
VERlFiCATlCN
?lace maintenance test phoneoff-hook.
Dial the 
Diagnos?ic Test Access Code.Dial 2 to enable trunk test.
Dial the two-digit trunk group number
(00 through 31) 
coniaining the trunk
circuit to be tested.
Dial the two-digit trunk number (00 
-99) of the trunk circuit to be tested.
For CO-type trunks (i.e., TMBM PCB),
dial the test tone number provided by
the local phone company.
Verify that the returned test tone lev-
el is correct, using a TMS.
If additional tests or procedures are
to be performed, hook-flash the main-
tenance test phone and dial the next
code (Diagnostic Test Access Code is
not redialed).
If no additional tests or procedures areto be performed, place the main-
tenance test phone on-hook.
Iial tone is returned.
jecall dial tone is returned.
done.
done.
20 or PABX dial tone is returned.41~0, the associated irunk circuit LEDIn the trunk PCB is lit steadily to in-licate the trunk has been seizedIutgoing.Test tone 
(1004Hz) is returned
Recall dial tone is returned.
None.IF VERIFICATION
IS NOT 
OETAINED
I jIf reorder tone is returned, the select-
ed trunk circuit is either an 
incoming-type, invalid, or not assigned (chec!cdata base assignments).
If busy tone is reiurned, the selected
trunk is in use, retry later.
If CO or PABX dial tone is not
returned, verify trunk MDF 
cross-connections and attempt to access
CO/PABX trunk using a butt set. If thetrunlc is working properly replace the
trunk PCB under test and retry test.
If the reiurned test tone level is weak,
replace PCB with another having the
same characteristics and retry test. If
returned test tone level increases con-
siderably, trunk PCB is defective and
should be replaced. If the test tone
level is still weak, contact CO repair
service to verify trunk facility.
i
i
6-26 
						

							-SATURN 
IIE EPABXA30i308-X5130-B120-1-B928Installation Test ProceduresIssue 1, May 1986.Table 6.12 Placing Circuit(s) In-Service
STEPPROCEDUREVERIF!CATIONIF VERlFlCATIOflIS NOT OBTAiNED*
1Place maintenance test phone Dial tone is returned.
off-hook.
2Dial the Diagnostic Test Access Code.Recall dial tone is returned.
3Dial 7 for placing a circuit in-service.None.
4AIf a single circuit is to be placed in-Coniirmation tone is returned.If reorder tone is returned, the seleci-service, dial the four digit PEN num-ed circuit is invalid or unassigned.
bar of the circuit.Check data base assignments.
45If all the circuits in a PCB are to beConfirmation tone is returned.If reorder tone is returned the select-
placed in-service, dial the first threeed PCB is invalid or unassigned
digits of the PEN number for the PCBCheck data base assignments,
followed by digit 8. For an SLA16, dialthe first three digits of the PEN num-
ber associated with the first eight cir-
cuits followed by an 8, then dial the
first three digits of the associated PENnumber for the second eight circuits
(W,X,Y+l) followed by an 8.
5AIf additional t&s or procedures areRecall dial tcne is returned.
to be performed, hoolcilash the main-
tenance test phcne and dial the next
code (Diagnostic Test Access Code is
not redialed).
5BIf no additional tests or procedures areNone.to be performed, place the main-
tenance test phone on-hook.
Table 6.73 Taking 
Ci:cuit(s) Out-et-Service
STEPPROCEDUREVERIFICATIONIF VERlFtCATIONIS NOT OBTAINED
1Place maintenance test phone Dial tone is returned.
off-hook.
2
Dial the Diagnostic Test Access Code.Recall dial tone is returned.
3Dial 8 for placing a circuit out-of- None.
service.
4A
48If a single circuit is to be placed 
out-Confirmation tone is returned.If reorder tone is returned, the select-
of-service, dial the four digit PENed circuit is invalid or unassigned.
number of the circuit.Check data base assignments.
If all the circuits in a PCB are to beConfirmation tone is returned.If reorder tone is returned the select-
placed out-of-service dial the firsted PCB is invalid or unassigned.
three digits of the PEN number for theCheck data base assignments.PCB followed by digit 8. For an SL416,dial the first three digits of the PEN
number associated with the first eight
circuits followed by an 8, then dial the
first three digits of the associated PENnumber for the second eight circuits
(W,X,Y+l) followed by an 8.
6-27 
						

							I  ’SATURN IIE EPABX
installation Test ProceduresTable 6.13 
Takinq Circuit(s) Out-of-Service IContinucdl
A30808-X5130-8120-1-8928
Issue 1, May 1986. ,
STEPPROCEDUREVERIFICATIONIF VERIFICATION
IS NOT OBTAINED
5AIf additional tests or procedures areRecall dial tone is returned.
to be performed, hook-flash the main-
tenance test phone and dial the next
code (Diagnostic Test Access Code is
not redialed).
5BIf no additional tests or procedures areNone.to be performed place the main-
tenance test phone on-hook..: j
6-28 (28 pages) 
						

							I.--SATURN 
IIE EPABXA30808-X5130-B120-143928Installation Test ProceduresIssue 1, May 1986
SECTKIN 7.00 INSTALLATION TEST PROCEDURES CHECKLlST
7.01General. After performing the installation test proce-
dures contained in this practice, each installation test proce-
dure performed should be recorded to ensure that all testshave been completed satisfactorily. Use Table 7.00, Installa-iion Test. Procedures Checklist, for this purpose. This table
can be used as a sign-off sheet, if required.
Table 7.00 Installation Test Procedures Checklist
7-l 
(7-2 bl!nnL,)