Sharp Ux Cl220 Plain Paper Fax And 2 4 Ghz Cordless Phone Wi Operation Manual

							Setting the Reception Mode
29
1. InstallationSetting the Reception Mode
Your fax has three modes for receiving incoming faxes:
FA X mode:
Select this mode when you only want to receive faxes on your line. The fax 
machine will automatically answer all calls on four rings and receive incoming 
faxes.
TEL mode:
Select this mode when you want to receive both phone calls and faxes on the 
line connected to the fax machine. All calls, including faxes, must be 
answered by picking up the fax machines handset or an extension phone 
connected to the same line.
TA D mode:
Select this mode when you go out and want the answering system to answer 
all calls. Voice messages will be recorded, and fax messages will be received 
automatically (“TA D” stands for “Telephone Answering Device”.)
Setting the reception mode
Make sure a document is not loaded in the document feeder, and then 
press   until the arrow in the display points to the desired mode.
RESOLUTION/
RECEPTION MODE
Note: TAD mode cannot be selected unless a general outgoing message has 
been recorded as explained on page 43.
For more information on receiving faxes in FAX and TEL modes, see Chapter 
6, Receiving Faxes. For more information on using TAD mode, see Chapter 3, 
Using the Answering System.
FAX TEL
JAN-01 10:30
FAX TEL
JAN-01 10:30
FAX TEL
JAN-01 10:30
TAD
TAD TAD
1
9
456
78
0
23RESOLUTION/
RECEPTION MODE
RESOLUTION/
RECEPTION MODE

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦ù

¦
¦


9
0
+
(
@ó
¦

(
5

						

							Volume Adjustment - Fax Machine
30
Volume Adjustment - Fax Machine
1Press .
2Press   or   until the display shows the desired volume level. 
•Press   again to turn off the speaker.
SPEAKER
SPEAKER
Speaker
1
9
456
78
0
23
SPEAKER
1When talking through the handset, 
press   or   until the display 
shows the desired volume level.
•Note: The volume reverts to MIDDLE 
each time you replace the handset.
Display:
Fax machine handset
RECEIVER: HIGH
RECEIVER: MIDDLE
RECEIVER: LOW
You can adjust the volume 
of the speaker, handset, 
and ringer using the up 
and down arrow keys.

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦ú÷
¦
¦


9
0
+
(
@ó
¦

(
5

						

							Volume Adjustment - Cordless Handset
31
1. Installation
1Press   or   until the display 
shows the desired volume level. 
(Make sure   has not been 
pressed, the handset is not lifted, and a 
document is not loaded in the feeder.)
•The ringer rings once at the selected 
level, and then the date and time 
reappear in the display.
2If you selected “RINGER: OFF OK ?” to 
turn off the ringer, press  .
SPEAKER
START/MEMORY
Fax machine ringer
Display:RINGER: HIGH
RINGER: MIDDLE
RINGER: LOW
RINGER: OFF OK ?
Volume Adjustment - Cordless Handset
You can adjust the volume 
of the ringer and handset, 
receiver using the up and 
down arrow keys.

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦úø
¦
¦


9
0
+
(
@ó
¦

(
5

						

							Volume Adjustment - Cordless Handset
32
Cordless handset ringer
1When you are not talking on the 
cordless handset, press   or   
until the display shows the desired 
ringer volume level.
•The ringer will ring once at the selected 
level.
2If you selected “RINGER: OFF OK ?” to 
turn off the ringer, press  .
START
RINGER: HIGH
Cordless handset display:
RINGER: MIDDLE
RINGER: LOW
RINGER: OFF OK ?
OK: PRESS START
1When talking on the cordless handset, 
press   or   until the display 
shows the desired volume level.
•Note: The volume reverts to MIDDLE 
each time you hang up (press ).
OFFOFF
RECEIVER: HIGH
Cordless handset display:
RECEIVER: MIDDLE
RECEIVER: LOW
Cordless handset receiver volume

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦úù
¦
¦


9
0
+
(
@ó
¦

(
5

						

							33
2. Setting Up 
OpenLCR
2.  Setting Up and Using OpenLCR
Your fax machine features OpenLCR technology, which helps you save money 
on long distance and international phone calls (both fax and voice) by 
automatically routing each call for the best available rate. 
♦OpenLCR service is free of charge. The only cost to you is that of a periodic 
call (usually once every three months) to OpenLCR to receive the latest 
rate data. (Once you have registered with OpenLCR, your fax machine 
automatically makes this call.)
♦All calls routed by OpenLCR are consolidated on your monthly phone bill.
You can register with OpenLCR by fax, phone, or through OpenLCR’s Web 
site (www.OpenLCR.com).
♦Before registering, be sure to read the information on the Fax 
Transmission Test and OpenLCR Line Activation Form and Te r m s  o f  
Service sheet included with your fax machine. If you have any questions, 
call OpenLCR at 970-206-1207.
♦OpenLCR uses Caller ID for identification purposes when your fax calls 
OpenLCR to receive rate information. Even if you have requested your 
telephone company to withhold your Caller ID information when you place 
calls, your fax will still automatically transmit this information only when it 
calls OpenLCR.
♦It is possible to register for and use OpenLCR if you do not subscribe to a 
Caller ID service; however, in some instances where rate data must be 
changed on an emergency basis, your fax may not be able to respond 
automatically to OpenLCR’s call to notify your fax that it must receive new 
rate data. If this occurs, old, incorrect data will continue to be used. 
♦Please note that the agreement you enter into by registering is between you 
and OpenLCR; it is not between you and any carriers.
To take advantage of this 
feature, you will need to 
register with OpenLCR 
and download the rate 
data to your fax machine.

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦úú
¦
¦


9
0
+
(
@ó
¦

(
5

						

							Setting Up and Using OpenLCR
34
 1Place the form with the side you wrote 
on face down, and push it gently into 
the document feeder of the fax 
machine.
2Press  ,  , and then  .
•Your fax  automatically calls OpenLCR and sends the form. After the form 
is sent, your fax will automatically receive the rate data. When downloading 
is completed, the display will briefly show DOWNLOAD OK!! and then 
revert to the date and time. Your fax will print out the registration form to 
confirm that it was received.
•OpenLCR will also program the date and time and your fax number in your 
fax machine.
OpenLCR5START/MEMORY
Registering by phone
To register by phone, follow these steps:
Registering by fax
To register by fax, fill in the Fax Transmission Test and OpenLCR Line 
Activation Form, and then fax the form as follows:
1Pick up the handset on the fax 
machine. 
2Press   and then  .OpenLCR1
READY TO SEND

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦úû
¦
¦


9
0
+
(
@ó
¦

(
5

						

							Setting Up and Using OpenLCR
35
2. Setting Up 
OpenLCR
3If the display shows the alternating 
messages at right, press the number 
keys to enter your fax/phone number, 
including the area code (the number 
must be 10 digits long). When finished, 
press .
(If the message at right doesn’t appear, 
this step is not necessary.)
4Follow the instructions you hear.
♦If you are on a pulse dial line, press   before pressing the number keys 
to respond. (This makes your fax temporarily issue tone signals when you 
press the number keys.)
♦When registration is completed, your fax machine will receive the rate data 
from OpenLCR. This will last one or two minutes. When downloading is 
completed, the display will briefly show DOWNLOAD OK!! and then revert 
to the date and time.
♦OpenLCR will also program the date and time and your fax number in your 
fax machine.
START/MEMORY
Registering through OpenLCR’s Web site
You can also register at OpenLCR’s Web site, www.OpenLCR.com. After 
registering you will need to receive the rate data manually (service is not 
activated until your fax receives the rate data). See Downloading (receiving) 
the rate data manually on the following page.
Important!
Be sure that you enter your correct 
area code and fax number. If not, 
your fax may not dial the correct 
number to connect to OpenLCR.
The rate data that you receive is based 
on the address you provide when 
registering with OpenLCR. If you move, 
the rate data will not be correct for your 
new location. In this case, repeat the 
registration procedure to give 
OpenLCR your new address.If you move, you 
must re-register!
SET OWN NUMBER
10 DIGITS

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦úü
¦
¦


9
0
+
(
@ó
¦

(
5

						

							Setting Up and Using OpenLCR
36
Note: If you wish to connect more than one OpenLCR-enabled device to the same 
line, please call OpenLCR at 970-206-1207. If you replace an old OpenLCR-
enabled device with a new one, you must re-register with OpenLCR to use the new 
device.
Note: OpenLCR cannot be used if your fax machine is connected to a Private 
Branch Exchange (PBX).
Downloading (receiving) the rate data manually
Your fax machine will automatically call OpenLCR and download updated rate 
data about once every three months. Normally you will not need to download 
the rate data manually. 
♦If you register through OpenLCR’s Web site, you must manually download 
the rate data to activate service.
♦If the fax machine is unplugged or some other interruption occurs in the 
power, you will need to manually download the rate data.
Press   and   to call OpenLCR and initiate downloading. Downloading 
lasts one or two minutes. During this time the display will show LCR 
DOWNLOADING. When downloading is completed, the display will briefly 
show DOWNLOAD OK!! and then revert to the date and time. OpenLCR will 
also program the date and time and your fax number in your fax machine.
Using OpenLCR
When you have registered with OpenLCR and downloaded the rate data to 
your fax machine, a highlighted “C” will appear in the date and time display to 
indicate that the OpenLCR feature is activated.
OpenLCR2
“C” indicates that 
OpenLCR is activated
FAX TEL
JAN-19 02:16
TAD
Each time you make a long distance phone or fax call, the fax machine will 
automatically route the call through the least expensive carrier based on the 
downloaded rate information.
Don’t unplug the 
fax, or the rate 
data will be lost!

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦úý
¦
¦


9
0
+
(
@ó
¦

(
5

						

							Setting Up and Using OpenLCR
37
2. Setting Up 
OpenLCR
Caution! If you unplug the fax machine or an interruption occurs in your 
power supply, the rate data will be erased. If this happens, the highlighted “C” 
in the display will blink to alert you.The fax machine will automatically call 
OpenLCR within the next 24 hours to receive new rate data; however, if you 
want to use OpenLCR service before that time, you should download the rate 
table manually as explained on page 36.
♦We recommend that you do not unplug the fax machine on a regular basis 
(for example at night or on the weekends), as this may result in a large 
number of calls to OpenLCR and a higher phone bill.
Symbols related to OpenLCR that may appear in the display are shown below. 
Mark Meaning
OpenLCR has been activated and is ready for use.
   (Blinking)OpenLCR cannot be used because the rate data has been erased. 
Your fax will automatically call OpenLCR within the next 24 hours to 
receive new data, or you can download the data manually if you need 
to use OpenLCR immediately (see page 36).
The rate data in the fax is no longer correct and the fax cannot connect 
to OpenLCR to obtain new data. See What to do if “E” appears in the 
display on page 39.
OpenLCR has been temporarily turned off. See Temporarily turning off 
OpenLCR below.
Rate data was not yet available when your fax called OpenLCR. Your 
fax will automatically call OpenLCR again when the rate data is 
available. Until that time, long distance calls will be routed through 
your primary carrier.
 (Blinking)Your fax will automatically call OpenLCR within the next 24 hours to 
learn when correct rate data will be available. 
Your fax did not receive the rate data because Open LCR was unable 
to identify your Caller ID. This problem could be noise on the phone 
line, or because your caller ID signal is blocked. Try retrieving the rate 
data several more times. If C appears, you have retrieved the rate 
data successfully. If you are still having problems, contact your phone 
company and make sure they support Caller ID. You can remove the 
H in your display by turning off the Open LCR function (press the 
OpenLCR key followed by #, 1, 8, 4, and #). You can also register for 
OpenLCR by phone to retrieve the rate data (see page 34).

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦úþ
¦
¦


9
0
+
(
@ó
¦

(
5

						

							Setting Up and Using OpenLCR
38
Temporarily turning off OpenLCR
If needed, you can temporarily turn off OpenLCR.
♦When you temporarily turn off OpenLCR, long distance and international 
calls will not be routed by OpenLCR. However, your fax will still call 
OpenLCR periodically to receive rate data.
1Press   once and   once.
 
2Press  once.
 3Press  once.
4Press   (NO) to turn off OpenLCR. (Press   (YES) to turn 
OpenLCR back on.)
•When you turn off OpenLCR, the highlighted “C” in the display will change 
to “-”.
5Press   to return to the date and time display.
FUNCTION
21
STOP
To stop using OpenLCR
If you want to stop using the Open LCR feature, press this sequence of keys: 
, , , , , 
♦Calls will not be routed by OpenLCR and the fax machine will not call 
OpenLCR to update data.
To resume use of OpenLCR, press , , , , , 
OpenLCR184
OpenLCR186
Display:
LCR SETTING
LCR DIAL
1=YES, 2=NO

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦úÿ
¦
¦


9
0
+
(
@ó
¦

(
5