Sharp Rcd1200m Manual

							EN-10
Express Defrost with 
Memory
*  Suppose you want to cook with memory 0, which was 
programmed for 10 minutes Express Defrost sequence, 
Single Digit Input/Auto Start ON.
Procedure
1  Place food in oven.
    Enter memory number.0
Midway through the defrosting cycle, the CHECK 
indicator will light in the display and an audible 
signal will be heard unless signal volume has been 
set to Mute. You may open the door, turn food over 
and shield any warm portions. Close the door.
MANUAL OPERATION
Time Cooking
Your oven can be programmed for up to 4 cooking 
sequences and has 11 preset microwave power levels.
Maximum Cooking Time
Microwave 100% - 60%  Maximum of   60 minutes 
Microwave   50% - 10%  Maximum of 120 minutes
(Please see Maximum Cooking Time on page EN-22)
Microwave Power Level
Press the SELECT 
POWER PAD
once then press
SELECT POWER
9
8
7
6
5
4
3
2
1
0Display
APPROXIMATE 
PERCENTAGE OF 
POWER
 100%
 90%
 80%
 70%
 60%
 50%
 40%
 30%
 20%
 10%
 0%
NOTES:
1.  It is not necessary to press the SELECT POWER pad 
for 100% in Single Stage Cooking.
2.  If cooking time input is over the maximum allowed 
time, error message EE9 will be displayed. Press the 
STOP/CLEAR pad to clear the error message and 
reduce cooking time or power level. For details, see 
Maximum Cooking Time on page EN-22.
Multi Stage Cooking
*  Suppose you want to cook for 1 minute at 70% power 
for 1st stage and then continue to cook for 2 minutes 
at 50% power for 2nd stage and to cook for 3 minutes 
at 100% power for 3rd stage.Procedure
3  Press the START pad.START
NOTES:
1.  Even though CHECK lights up in the display,  your oven 
continues defrosting and does not stop to check.
2. Press the START pad at step 2 to continue defrosting 
as once the door is closed, cooking data will be 
canceled if subsequent keys are not pressed within 
3 minutes.
3.  See HELPFUL TIP for Express Defrost on page EN-11.
Procedure
2  Press the START pad to continue  
defrosting.START
Single Stage Cooking
*  Suppose you want to cook for 2 minutes and 30 
seconds at 50%.
1  Place food in oven and 
press the SELECT TIME 
pad. Enter cooking time.Procedure
2  Press the SELECT POWER pad 
and enter power level.SELECT
POWER5
230
SELECT
TIME
1  Place food in oven and press 
the SELECT  TIME pad.  
  Enter cooking time  for 1st 
stage.
Procedure
2   Press the SELECT POWER pad.
  Enter power level for 1st stage.
3   Press the SELECT TIME pad.
  Enter cooking time  for 2nd 
stage.
SELECT
POWER7
100
SELECT
TIME
200
SELECT
TIME 
						

							EN-11
Procedure
4   Press the SELECT POWER pad.
  Enter power level for 2nd stage.
5  Press the SELECT TIME pad.
  Enter cooking time  for 3rd 
stage.
SELECT
POWER5
300
SELECT
TIME
6  Press the START pad.START
NOTES: 
1.  It is not necessary to press the SELECT POWER pad 
for 100% at the last stage in Multi Stage Cooking.
2.  If the Total Cooking Time is over the maximum time 
allowed, error message, EE9 will be displayed. Press 
the STOP/CLEAR pad to clear the error message pad 
and reduce Total Cooking Time, power levels or stages. 
For details, see Maximum Cooking Time on page 
EN-22.
Express Defrost
Use EXPRESS DEFROST to defrost meat and poultry. 
Calculate total defrost time using chart below. Express 
Defrost can be programmed for a maximum of 90 
minutes.
*  Suppose you want to defrost one pound of lamb chops 
for 3 minutes and 30 seconds.
Procedure
3  Press the START pad.START
HELPFUL TIP for Express Defrost
Allow foods to stand a few minutes after defrosting to 
equalize the temperature for better cooking results.
Check food after standing. If additional time is needed, 
continue to defrost with manual cooking. 
Foods that are the same thickness throughout 
defrost better. If foods have varied thickness, it may 
be necessary to shield the thin edges with small  at 
pieces of aluminum foil to prevent overdefrosting.
Midway through the defrosting cycle, the CHECK 
indicator will light in the display and an audible 
signal will be heard unless signal volume has been 
set to Mute. You may open the door, turn food over 
and shield any warm portions. Close the door.
4  Press the START pad to continue  
defrosting.START
NOTES:
1.  Even though CHECK lights up the display,  your oven 
continues defrosting and does not stop to check.
2. Press the START pad at step 4 to continue defrosting. 
Once the door is closed, cooking data will be 
canceled if subsequent keys are not pressed within 
3 minutes.
 less than 1
more than 1
1
 less than 1
more than 1
1/2–3/43/4–11/2–3/43/4–1  
Beef steak
Lamb chops
Pork chops
Boneless chicken  
 breasts
Fish steakTime (min./lb.)
Thickness
Food
R-CD1800M
2–21/221/2–31/2
2–31/2
2–21/221/2–31/2
2–3
21/2–31/2
11/4–2
13/4–21/2
R-CD2200M
1
3/4–21/42–3
13/4–23/4
13/4–21/42–3
11/2–21/22–3
1–13/411/4–2
Express Defrost Chart
Procedure
1  Place food in oven. 
  Press the EXPRESS DEFROST pad.EXPRESS
DEFROST 
2  Enter defrosting time.  
(Refer to chart below.)330
R-CD1200M
4–4
1/25–51/2
4–5
31/2–4
5–51/2
4–5
41/2–51/2
2–3
3–4 
						

							EN-12
PROGRAM & CUSTOMIZE
Custom Help
You can check your oven settings and customize your 
oven by changing Custom Help settings.
The CUSTOM HELP pad has 11 operations. 
  1. Selecting Memory Input Method
  2. Selecting Auto Start Operation
  3. Program Lock Setting
  4. Audible Signal Sound Volume Setting
  5. Cooking Completion Signal Setting  
 6. Memory Check
 7. Counter Check/Clear
  8. Air Intake Filter Counter
  9. Selecting Operation in case of Magnetron Failure
 10. Multiplication Factors for Double/Triple  Quantity
 11. Express Defrost Setting 
To use Custom Help Function, press the CUSTOM HELP 
pad twice within 2 seconds, and desired option pads. 
See detailed instructions below.
NOTE : You will hear an audible signal the second time 
the CUSTOM HELP pad is pressed to indicate that you 
have entered Custom Help.
1.  Selecting Memory Input Method
Your oven has 3 ways to select memory numbers.
CH11 : Dual Digit Input (100 memory banks) 
= Factory  Setting
CH12  :  Single Digit Input (10 memory banks) 
CH13  :  Repeat Digit Input (30 memory banks)
To set Input Method
Press the CUSTOM HELP pad twice within 2 seconds then 
enter the numbers
1,1 for Dual Digit Input
1,2 for Single Digit Input
1,3 for Repeat Digit Input
Press the START pad to save settings and the STOP/
CLEAR pad to exit from the Custom Help Function.  
*  Suppose you want to set Repeat Digit Input.
x 2
Procedure
1  3
STOP
CLEAR
1  Press the CUSTOM HELP pad 
twice within 2 seconds.
2  Enter 1,3 for Repeat Digit 
Input.
3  Press the START pad to save 
the setting.START
4 Press the STOP/CLEAR pad 
to exit from the Custom Help 
function.
CUSTOM
HELP
2.  Selecting Auto Start Operation
Your oven has 2 ways to start memory cooking.
CH21  :  Auto Start OFF = Factory Setting
CH22  :  Auto Start ON 
The factory setting is Auto Start OFF. Under Auto Start 
OFF, cooking will not begin until the START pad is 
pressed. Under Auto Start ON, cooking will automatically 
start after the memory number is input. 
To set AUTO START
Press the CUSTOM HELP pad twice within 2 seconds then 
enter the numbers 
2, 1 for Auto Start OFF
2, 2 for Auto Start ON
Press the START pad to save settings  and  the STOP/
CLEAR pad to exit from the Custom Help Function.
*  Suppose you want to set Auto Start ON.
Procedure
2  2
STOP
CLEAR
x 2CUSTOM
HELP1  Press the CUSTOM HELP pad 
twice within 2 seconds.
2  Enter 2, 2 for Auto Start ON.
3  Press the START pad to save 
the setting.START
4 Press the STOP/CLEAR pad 
to exit from the Custom Help 
Function.
3.  Program Lock Setting 
You can select Program Lock  ON or OFF
CH31  :  Program Lock OFF = Factory Setting
CH32  :  Program Lock ON
Program Lock OFF is the Factory setting. Program Lock 
prevents accidental changes to settings. When the 
CUSTOM HELP pad is pressed twice within 2 seconds 
in program Lock ON, the LOCK indicator will light up. 
Turn Program Lock OFF when you want to change the 
settings.
To turn Program Lock ON/OFF  
Press the CUSTOM HELP pad twice within 2 seconds then 
enter the numbers
3, 1 for Program Lock OFF
3, 2 for Program Lock ON
Press the START pad to save settings and  the STOP/
CLEAR pad to exit from the Custom Help Function. 
						

							EN-13
*  Suppose you want to set Program Lock ON.
x 2
Procedure
3  2
STOP
CLEAR
CUSTOM
HELP1  Press the CUSTOM HELP pad 
twice within 2 seconds.
2  Enter 3, 2 for Program Lock 
ON.
3  Press the START pad to
  save the setting.START
4  Press the STOP/CLEAR pad 
to exit from the Custom Help 
Function.
NOTE : If you select Program Lock OFF, the LOCK 
indicator in the display will disappear when you press 
the START pad.
Operation when Program Lock ON is set
KEY 
OperationCustom Help TitleWhen Program 
Lock ON is set
1Selecting Memory 
Input Methodno operation
2Selecting Auto Start 
Operationno operation
3Program Lock 
Settingoperation
4Audible Signal 
Sound Volume 
Settingno operation
5Cooking Completion 
Signal Settingno operation
6 Memory Check operation
7Counter Check/Clear check : operation
clear : 
no operation
8Air Intake Filter 
Countercheck, clear : 
operation 
set : no operation
9Selecting Operation 
in case of Magnetron 
Failureno operation
x2/x3Multiplication 
Factors for Double/
Triple Quantitycheck : operation
set : no operation
EXPRESS
DEFROSTExpress Defrost 
Settingcheck : operation
set : no operation
4.  Audible Signal Sound Volume Setting
The volume of the audible signal can be adjusted to 
High, Medium, or Mute.
CH41  :  High = Factory Setting
CH42 :  Medium
CH43 :  Mute
To set cooking completion signal volume
Press the CUSTOM HELP pad twice within 2 seconds then 
enter the numbers 
4, 1 for High
4, 2 for Medium
4, 3 for Mute
Press the START pad to save setting and the STOP/CLEAR  
pad to exit from the Custom Help Function. 
NOTE : Even when errors occur, your oven will not beep 
in mute setting.
5.  Cooking Completion Signal Setting
There is a choice of  4 different signals on your oven.
CH51  :  1 long beep = Factory setting
CH52  :  Repeating long beeps 
CH53  :  4 short beeps
CH54  :  Repeating short beeps
To set the signal type
Press the CUSTOM HELP pad twice within 2 seconds then 
enter the numbers
5, 1 for 1 long beep
5, 2 for repeating long beeps 
5, 3 for 4 short beeps
5, 4 for repeating short beeps  
Press the START pad to save settings and the STOP/
CLEAR pad to exit from the Custom Help Function. 
6. Memory Check
Use this setting to check the programming for a certain 
memory.
* Suppose you want to know the information 
programmed into memory 1, programmed 
for 4 minutes at 60% for the 1st stage and 
2 minutes at 30% at the 2nd stage programmed Dual 
Digit Input.
 Procedure  Display
1  Press the CUSTOM HELP pad 
twice within 2 seconds and 
enter 6.
CUSTOM
HELP
x26
CHECK NO. 
						

							EN-14
 Procedure  Display
2  Enter memory number.
  (After entering the 
memory number, the 
memory setting of each 
content is shown for 
1.5 seconds at 0.3 second 
intervals until the STOP/
CLEAR pad is pressed.)
1
0  
After about 1 sec.CHECK
CHECK
CHECK
CHECK
CHECK
CHECK
STOP
CLEAR
3  Press the STOP/CLEAR pad       
to exit from the Custom Help 
Function.
CHECKNO.
CHECK
NOTES:
1. If 
CHECK  is displayed at step 2 the memory has not 
been programmed.
2. Multiple memories can be checked until the STOP/
CLEAR pad is pressed to exit from the Custom Help 
Function.
3.  The way to enter memory numbers depends  on the 
programmed Memory Input Method.
4. When Express Defrost is set for 30 minutes in 
the memory, 
 and  are displayed 
repeatedly at step 2.
7. Counter Check/Clear
Con rm counters are set to 0 before using oven for 
the  rst time.
Counter Check
Counter check can be used to check the total number of 
times the oven has been used, or the number of times 
each pre-programmed memory pad, manual cooking, 
or Express Defrost has been used.
Total usage  Press the CUSTOM HELP pad twice 
within 2 seconds, then enter 7. Total 
usage will be displayed.
NO.
To check more than one counter
Press each pad as indicated below, after the previous 
usage is displayed.
Total each  Input memory number.
memory usage
Total manual  Press the SELECT TIME 
cooking usage pad.
Total Express  Press the EXPRESS 
Defrost usage DEFROST pad.
*  Suppose you want to know total usage and each 
memory usage. In this case the oven was used 8268 
times and memory 1 in any Memory Input Method 
was used 513 times.
NO.          CHECK  NO.      CHECK
 Procedure  Display
1  Press the CUSTOM 
HELP pad twice within 
2 seconds, then enter 
7. Total usage will be 
displayed.
x 2CUSTOM
HELP
2 Enter memory 
number 1, to check 
the total memory 
usage of memory 1.After about 1 sec.
7
CHECK
0
1
CHECK
After about 1 sec.
NOTES:
1.  To exit from Counter Check, press the STOP/CLEAR 
pad.
2. Each counter will count up to 9999, and then will 
automatically reset to 0 and begin counting again.
3.  As shown in the above example, multiple counters 
can be checked before pressing the STOP/CLEAR pad 
to exit.
4. Only Dual Digit Input Method can be used when 
inputting memory numbers in Counter Check/Clear. 
						

							EN-15
NOTES:
1. Only Dual Digit Input method can be used when 
inputting memory numbers in Counter Check/Clear.
2.  To clear total manual cooking usage, press the SELECT 
TIME pad in Step 2 instead of the number pad.
3. To clear total Express Defrost usage, press the 
EXPRESS DEFROST pad in Step 2 instead of the 
number pad.
4.  To clear total usage, skip Step 2.
8.  Air Intake Filter Counter
Use Custom Help Function for Air Intake Filter Counter 
to check total usage hours since the Air Intake Filter was 
last reset to “0”.
CH81 : The total used air intake filter time 
appears.
CH82 : The limit time for using a  lter can be 
changed.After about 1 sec.
NO.          CHECKNO.      CHECK
1  Press the CUSTOM 
HELP pad twice within 2 
seconds, then enter 7 . 
Total usage will be
displayed.
Procedure
x 2CUSTOM
HELP
2 Enter memory 
number 1 to 
check the total 
memory usage of 
memory 1.
START
3  Press the START pad.
CHECK
0
7
1
CHECK
CHECK
After about 1 sec.
STOP
CLEAR
4 Press the STOP/CLEAR pad 
to exit from the Custom Help 
Function.
To Reset the Counter to “0”
Each counter can be manually reset to “0” by pressing 
the START pad after the count is displayed.
*  Suppose you want  to reset the count for memory 
number 1 in any Memory Input MethodUse Custom Help Function for Air Intake Filter Counter 
to change the Air Intake Filter cycle from 001-999. The 
factory setting is 100 hours. When 100 hours is exceeded, 
the FILTER indicator on the display will start to  ash on 
and off as a reminder to clean the air   lter, even if in the 
middle of cooking. Furthermore “FILt“   ashes on and 
off   in stead of displaying “ . “ during standby and at the 
same time FILTER indicator   ashes on and off.  Clean Air 
Intake Filter (See page EN-23 - EN-24), when the FILTER 
indicator appears in the display, and then clear the total 
usage to reset it to “0” .
*  Suppose you want to know the total usage hours 
which has been 99 hours since the last reset.
To Reset the Air Intake Filter Counter
Reset the Air Intake Filter Counter after cleaning the air 
intake  lter.
*  Suppose you want to reset the air   lter counter which 
has been 101 hours since the last reset and the Air 
Intake Filter cycle is preset to 100.
1   Press the CUSTOM HELP 
pad twice within 
2 seconds and enter 8, 1.
 Procedure  Display
CUSTOM
HELP
x281
After about 1 sec.
CHECK
 Procedure  Display
1  Press the CUSTOM HELP 
pad twice within 
2 seconds and enter 8,1.
2  Press the START pad to 
reset the counter to “0”.
x281CUSTOM
HELP
CHECK
START
STOP
CLEAR
2  Press the STOP/CLEAR pad to exit from the 
Custom Help Function.
STOP
CLEAR
3  Press the STOP/CLEAR pad to exit from 
the Custom Help Function.
FILTER
After about 1 sec. 
						

							EN-16
Air Filter Cycle
Air Filter Cycle can be changed from the factory setting 
of 100 hours to 001-999 hours
*  Suppose you want to set the cycle to 250 hours.
 Procedure  Display
2  Press the SELECT TIME pad.
3  Enter desired time.
  (Ex : Enter 2, 5, 0 for 250 
hours).  
1  Press the CUSTOM HELP 
pad twice within 2 seconds 
and enter 8, 2.
SELECT
TIME
x282CUSTOM
HELP
2 5 0 
After about 1 sec.
CHECK
4  Press the START pad to save settings.
START
STOP
CLEAR
5  Press the STOP/CLEAR pad to exit from the 
Custom Help Function.
9.  Selecting Operation in case of Magnetron Failure
Your oven has 2 magnetrons. In case of single magnetron 
failure, the oven can be used until servicing by changing 
settings to allow operation under single magnetron only. 
However, check food carefully as additional cooking 
time will be needed when operating with a single 
magnetron.
CH91 :  Your oven does not work when one magnetron 
fails =  Factory setting
CH92  :  Your oven works even if one magnetron  
fails.
To set magnetron failure options
Press the CUSTOM HELP pad twice within 2 seconds then 
enter the numbers
9, 1 to stop operation when one magnetron fails
9, 2 to allow operation of one magnetron only 
Press the START pad to save settings and the STOP/
CLEAR pad to exit from the Custom Help Function. 
10.  Multiplication Factor for Double/Triple Quantity
The multiplication factors of the double and triple 
quantities for memory cooking are preset to 1.80 
and 2.60. You can check or change the multiplication 
factors.
*  Suppose you want to know the multiplication 
factor for double quantity with memory 1, and change 
it to 2.00 in any Memory Input Method.
 Procedure  Display
2  Enter memory number.
3  Press the SELECT TIME pad.
1  Press the CUSTOM HELP pad 
twice within 2 seconds and 
press the DOUBLE/TRIPLE 
QUANTITY pad.
SELECT
TIME
0
1
CHECK
After about 1 sec.
CHECKNO.
CHECKNO.
CHECK NO.
x2
CUSTOM
HELPx2/x3
2 0 0 
4  Enter desired multiplication.
  (Ex : Enter 2, 0, 0 for 2.00.)
5  Press the START pad to save 
settings.
CHECKNO.
START
STOP
CLEAR
6  Press the STOP/CLEAR pad to exit from 
the Custom Help Function. 
						

							EN-17
NOTES:
1. Only Dual Digit Input method can be used when 
inputting memory numbers in Multiplication Factor 
for Double/Triple Quantity.
2.  The multiplication factors can be set from 0.01 to 9.99  
for double quantity and  triple quantity.
3.  When you want to know the multiplication factor for 
triple quantity, press the DOUBLE/TRIPLE QUANTITY 
twice at step 1 after pressing the CUSTOM HELP pad 
twice.
4.  Multiplication Factors for Double/Triple Quantity can 
be checked or changed before pressing the STOP/
CLEAR pad to exit for Custom Help Function.
11. Express Defrost Setting
Express Defrosting uses 3 stages to defrost foods 
quickly.
The defrosting sequence is preset as follows, but you 
can change the setting.
Defrosting Time Power Level
STAGE 
1T  x A1: (0.20*) + B1: (20*) 
sec.PL1 (40*) %
STAGE 
2T x A2: (0.13*) + B2: (30*) 
sec.PL2 (30*) %
STAGE 
3T - STAGE1 - STAGE2 PL3 (20*) %
Pause
TimingSee the table for The Pause 
Timing below (50*)
T  :  INPUT TIME (TOTAL COOKING TIME)
*  :  The numbers in the parentheses are factory settings 
and can be adjusted.
Express Defrost is preset to pause during the sequence 
when 50% of total defrosting time has passed to check 
food. Pause timings can also be adjusted. 
Pause Timing
KEY
DisplayPause Timing
0 0 No pause.
1 1 After 10% of total cooking time.
2 2 After 20% of total cooking time.
3 3 After 30% of total cooking time.
4 4 After 40% of total cooking time.
5 5 After 50% of total cooking time.
6 6 After 60% of total cooking time.
7 7 After 70% of total cooking time.
8 8 After 80% of total cooking time.
9 9 After 90% of total cooking time.
START A After ending of each stage
3  Press the SELECT TIME 
pad and enter desired 
time for B1 at Stage 1.
  (Ex: Enter 1 for 
10 seconds.)SELECT
TIME
1
DEF.
DEF.
2  Press the SELECT TIME 
pad and enter desired 
multiplication for A1 at 
Stage 1.
  (Ex: Enter 3,0 for 0.30.)
DEF.SELECT
TIME
3
0DEF.
SELECT
POWER
5
DEF.
DEF. DEF.
4  Press the SELECT 
POWER pad and enter 
desired power level for 
PL1 at Stage 1.
  (Ex: Enter 5 for 50%)
*  Suppose you want to change the Express Defrost set 
factory settings to the following:
Defrosting TimePower 
Level
STAGE 1 T x 0.30 + 10 sec.  50%
STAGE 2 T x 0.15 + 20 sec.  20%
STAGE 3 T - STAGE1 - STAGE2 10%
Pause 
TimingWhen 70% of total defrosting time has 
passed.
 Procedure  Display
1 Press the CUSTOM 
HELP pad twice 
within 2 seconds 
and press the 
EXPRESS DEFROST 
pad.
 (The Express 
Defrost setting 
of each phase 
is shown for 1.5 
seconds per 0.3 
seconds until the 
SELECT/TIME pad is 
pressed.)
x2
CUSTOM
HELPEXPRESS
DEFROST
CHECKDEF.
CHECKDEF.
CHECKDEF.
CHECKDEF.
CHECKDEF.
CHECKDEF.
CHECKDEF.
CHECKDEF.
CHECKDEF.
CHECKDEF.
CHECK DEF.
(STAGE 1)
(A1)
(B1)
(Power Level 1)
(STAGE 2)
(A2)(B2)
(Power Level 2)
(STAGE 3)
(Pause Timing)
(Power Level 3) 
						

							EN-18
 Procedure  Display
  5  Press the SELECT TIME 
pad and enter desired 
multiplication for A2 at 
Stage 2.
    (Ex: Enter 1, 5 for 0.15.)SELECT
TIME
1
5
DEF.
DEF.
DEF.
  6  Press the SELECT TIME 
pad and enter desired 
time for B2 at Stage 2.
    (Ex: Press 2 for 
20 seconds.)SELECT
TIME
2
DEF.
DEF.
  8  Press the SELECT TIME 
pad and enter the pause 
timing.
    (Ex: Enter 7 for when 70% 
of total defrosting time 
has passed.)SELECT
TIME
7
DEF.
  7  Press the SELECT  
POWER pad and enter 
desired power level for 
PL2 at Stage 2.
    (Ex: Enter 2 for 20%)SELECT
POWER
2DEF.
DEF.
DEF.
DEF.
DEF.
 10  Press the START pad.
START
STOP
CLEAR
 11  Press the STOP/CLEAR pad to exit from 
the Custom Help Function.
  9  Press the SELECT 
POWER pad and enter 
desired power level for 
PL3 at Stage 3.
    (Ex: Enter 1 for 10%)
NOTES: 
1. See the table for Microwave Power  Level on 
page EN-10 and The Pause Timing on page 
EN-17.
2.  You can enter minus numbers for B1 and B2 at steps 
3 and 6. 
  In that case,
  press the SELECT TIME pad twice at step 3 or 6
(
 is displayed.) and enter desired time for or 
B1 and B2 at Stage 1 and 2.
  Press the SELECT TIME pad again to enter positive 
numbers. (  is displayed.)
Saving Memories
*  Memory 0 - 9 are programmed as  factory settings.  
See  the table of Programmed Memories on page 
EN-8.  
*  Memories must be programmed before memory 
cooking can be used.
Memory banks
Dual Digit: Memory 0-99
Single Digit: Memory 0-9
Repeat Digit Input: Memory 0-29
Max. cooking stages: 4 stages
Setting time and power level for 
Single Stage

*  Suppose you want to set 1 minute at 70% with memory 
2.
1  Press the SET MEMORY pad 
twice within 2 seconds.
NO.
NO.2  Enter memory number.
2
3  Press the SELECT TIME pad.
4  Enter cooking time.
1  0  0
NO.
6  Enter power level.
7
5  Press the SELECT POWER pad.
7  Press the SET MEMORY pad to 
save memory.
8  Press the STOP/CLEAR pad to exit.
 Procedure  Display
SELECT
POWERSELECT
TIME 
STOP
CLEAR
SELECT
POWER
1
X 2SET
MEMORY
SET
MEMORY 
						

							EN-19
NOTES: 
1.  Press the SET MEMORY pad twice within 2 seconds.
2. If the cooking time is over the maximum time, the 
display will show error code EE9. To clear the error 
code, press the STOP/CLEAR pad and re-program. 
See Maximum Cooking Time on page EN-22.
3.  It is not necessary to press the SELECT POWER pad 
for 100% in Single Stage.

*  Suppose you want to set 1 minute at 70% with memory 
12.
1  Press the SET MEMORY pad 
twice within 2 sec.
2  Enter memory number.
NO.
NO.
2  2
3  Press the SELECT TIME pad.
4  Enter cooking time.
1  0  0
5  Press the SELECT POWER pad.
6  Enter power level.
7  Press the SET MEMORY pad.
8  Press the STOP/CLEAR pad to exit.
NO.
7
NOTES:
1.  Press the SET MEMORY pad twice within 2 seconds.
2.  If the programmed cooking time is over the maximum 
time, the display will show error code EE9. To clear 
the error code, press the STOP/CLEAR pad and 
re-program. See Maximum Cooking Time on page 
EN-22.
3.  It is not necessary to press the SELECT POWER pad 
for 100% in Single Stage.
 Procedure  Display
SELECT
TIME
SELECT
POWER
STOP
CLEAR

*  Suppose you want to set 4 minutes at 60% with 
memory 1 and 2 minutes at 30% with memory 2. 
  1  Press the SET MEMORY pad 
twice within 2 seconds.
  3  Press the SELECT TIME pad.
  4  Enter cooking time for memory 1.
  5  Press the SELECT POWER pad.
  6  Enter power level for memory 1.
  8  Enter memory number.NO.
NO.
NO.
NO.
4  0  0
0  1
6
0  2
  9  Press the SELECT TIME pad.
10   Enter cooking time for memory 2.
11   Press the SELECT POWER pad.
2  0  0
 Procedure  Display
  2  Enter memory number.
SELECT
TIME
SELECT
POWER
  7  Press the SET MEMORY pad to 
save memory 1.
SELECT
TIME
SELECT
POWER
X 2SET
MEMORY
SET
MEMORY
X 2SET
MEMORY
SET
MEMORY