Sharp Mxm264n User Guide

5-93
SCANNER/INTERNET FAX
Contents
5
Press the [START] key.
Scanning begins.
To cancel scanning...
Press the [STOP] key ( ) to cancel the operation. All scanned data will be cleared.
6
When scanning ends, check the number 
of original sheets scanned and touch the 
[OK] key.
Transmission will begin.
 When Job Build mode is used, the confirmation message will 
appear after the [Read-End] key is touched.
 The message on the screen shows the number of sheets 
scanned in (A), and the number of pages (sheet...

5-94
SCANNER/INTERNET FAX
Contents
STAMPING SCANNED ORIGINALS (Verif. Stamp)
This function stamps each original that is scanned using the automatic document feeder, allowing you to verify that all 
originals were correctly scanned.
 To use this function, the automatic document feeder and optional stamp unit must be installed.
 When using USB memory mode, connect the USB memory device to the machine before performing the procedure below.
1
Insert the originals face up in the 
document feeder tray.
2...

5-95
SCANNER/INTERNET FAX
Contents
4
Select Verif. Stamp.
(1) Touch the   keys to switch through the 
screens.
(2) Touch the [Verif. Stamp] key so that it is 
highlighted.
(3) Touch the [OK] key.
5
Press the [START] key.
Scanning begins. A beep will sound to indicate that scanning is finished.
To cancel scanning...
Press the [STOP] key ( ) to cancel the operation.
 When two-sided originals are used, the front of each original is stamped twice.
 If an error occurs during scanning, an original that was...

5-96
SCANNER/INTERNET FAX
Contents
ELIMINATING BLANK PAGES FROM A 
TRANSMISSION (Blank Page Skip)
When blank pages are included in originals scanned using the automatic document feeder, the blank pages can be 
detected and automatically eliminated from transmission.
 This function cannot be used in Internet fax mode.
 Depending on the original, some pages that are not blank may be detected as blank pages and thus not sent, and some 
pages that are blank may not be detected as blank and thus sent.
...

5-97
SCANNER/INTERNET FAX
Contents
4
Set blank page skipping.
(1) Select the type of blank page to be skipped.
Select from two types.
To include blank pages on which the content on the 
opposite side shows through, touch [Skip Blank and Back 
Shadow].
(2) Touch the [OK] key.
5
Press the [START] key.
Scanning begins. A beep will sound to indicate that scanning is finished.
To cancel scanning...
Press the [STOP] key ( ) to cancel the operation.
6
When scanning is completed, check the 
number of original...

5-98
SCANNER/INTERNET FAX
Contents
SENDING TWO PAGES AS A SINGLE PAGE 
(2in1)
Two original pages can be reduced to half their original size and sent together as a single page.
This function cannot be used in scan mode, USB memory mode, or data entry mode.
1
Place the original.
When placing the originals, orient them as shown below.
2
Specify the destination.

ENTERING DESTINATIONS (page 5-18)
12
12
12
1
2
Portrait-oriented originals
Landscape-oriented originalsTransmission
Transmission
12
12
1
1
1
1...

5-99
SCANNER/INTERNET FAX
Contents
3
Select the special modes.
(1) Touch the [Internet Fax] tab.
(2) Touch the [Special Modes] key.

SPECIAL MODES (page 5-71)
4
Select 2in1.
(1) Touch the [2in1] key so that it is 
highlighted.
(2) Touch the [OK] key.
5
Touch the [Original] key.
6
Specify the orientation in which the 
original is placed.
(1) Touch the Image Orientation key with the 
same orientation as the original image.
If this setting is not correct, a suitable image may not be 
transmitted.
(2) Touch...

5-100
SCANNER/INTERNET FAX
Contents
7
Press the [START] key.
Scanning begins.
 If you inserted the original pages in the document feeder tray, all pages are scanned. 
A beep will sound to indicate that scanning is finished.
 If you are scanning the original on the document glass, scan each page one page at a time. 
When scanning finishes, place the next original and press the [START] key. Repeat until all pages have been scanned and 
then touch the [Read-End] key. 
A beep will sound to indicate that...

5-101
SCANNER/INTERNET FAX
Contents
CHANGING THE PRINT SETTINGS FOR THE 
TRANSACTION REPORT 
(Transaction Report)
A transaction report is automatically printed out to alert you when an Internet fax transmission fails or when a broadcast 
transmission is performed. The transaction report contains a description of the transmission (date, start time, name of 
other party, time required, number of pages, result, etc.).

INFORMATION APPEARING IN THE RESULT COLUMN (page 5-111)
Transaction reports are printed...

5-102
SCANNER/INTERNET FAX
Contents
5
Press the [START] key.
Scanning begins.
 If you inserted the original pages in the document feeder tray, all pages are scanned. 
A beep will sound to indicate that scanning is finished.
 If you are scanning the original on the document glass, scan each page one page at a time. 
When scanning finishes, place the next original and press the [START] key. Repeat until all pages have been scanned and 
then touch the [Read-End] key. 
A beep will sound to indicate that...