Sanyo Projector PLV-Z2000 User Manual

Multimedia  Projector 
MODEL PLV-Z2000
Owner’s Manual 

2

This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. It uses built-in 
multimedia features, a palette of 1.07 billion colors, and matrix liquid crystal display (LCD) technology.
 ◆ Short Throw & Wide-Range Zoom Lens
  The 2x Short Throw & Wide-Range Zoom Lens is capable of 
throwing a 100” diagonal image from a distance of 9.8’ (3.0 
m) to 20.0’ (6.1 m).
◆ Lens Shift
  The Lens Shift function provides a greater installation...



TRADEMARKS
● Each name of corporations or products in this owner’s manual is either a trademark or a registered trademark of its 
respective corporation.
Table of Contents
Features and Design .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .2
Table of Contents   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .
To the Owner   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .4
Safety Instructions .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .5
Air Circulation 6
Installing the...

4
CAUTION: TO REDUCE THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER (OR 
BACK) .  NO USER-SERVICEABLE PARTS 
INSIDE EXCEPT LAMP REPLACEMENT  .  
REFER SERVICING TO QUALIFIED 
SERVICE PERSONNEL .
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER’S MANUAL WITH THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Before operating this projector,...

5
All the safety and operating instructions should be read before 
the product is operated.
Read all of the instructions given here and retain them for 
later use. Unplug this projector from AC power supply before 
cleaning. Do not use liquid or aerosol cleaners. Use a damp 
cloth for cleaning.
Follow all warnings and instructions marked on the projector.
 
For added protection to the projector during lightning storm, or 
when it is left unattended and unused for long periods of time, 
unplug it from...

6
Moving	the	Projector
When moving the projector, make sure that the automatic 
slide shutter is closed, retract the adjustable feet, and lock the 
lens with the Lens Shift Lock to prevent damage to the lens 
and cabinet.
When the projector is unused for an extended period, put it 
into a suitable case.
Care must be taken when handling the projector; do not drop, 
bump, subject it to strong forces, or put other things on the 
cabinet. 
20
20
Do not tilt the projector more than 20 
degrees from side to...

7
AC Power Cord for the United Kingdom:
 This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the 
fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus ASA. If the fuse cover is 
detachable,  never  use  the  plug  with  the  cover  omitted.  If  a  replacement  fuse  cover  is  required,  ensure  it is of the same colour as that 
visible on the pin face of the plug (i.e....

8

Bottom
Back
!2
!3!4
!6 Adjustable Feet
!7  RGB Panel Cleaning Hole Cover
!1
!6
!5
!1  Terminals and Connectors
!2  Main On/Off Switch
!3  Power Cord Connector
!4  Air Intake Vent
!5	Lamp Cover
✽ Kensington Security Slot  This slot is for a Kensington lock used to deter theft of the projector. *Kensington is a registered trademark of ACCO Brands Corporation.
q Exhaust VentFront
q
erytuo
w  Top Controls and Indicators 
e  Automatic Slide Shutter
r  Projection Lens
t  Focus Ring 
y  Zoom Lever
u...

9

q COMPUTER
 Connect the computer output signal, or RGB Scart 21-pin 
video output to this connector (p.16).
Rear	Terminal
qw
t
e
y VIDEO 
  Connect the composite video output signal from video 
equipment to this jack (p.15).e COMPONENT 1 or COMPONENT 2
  Connect the component video output signal to these jacks 
(p.15).
w  S-VIDEO
 Connect the S-Video output signal from video equipment 
to this jack (p.15).
r  SERVICE PORT
  This jack is used to service the projector. 
r
y
t HDMI 1/HDMI 2*
  Connect...

10

Top	Control
qwe
r
tyui
i INFO  . button
 Display the input source information (p.43).
t  INPUT button
 Select an input source (p.24).
e  LAMP REPLACE indicator
 Lights yellow light when the projection lamp reaches its 
end of life (pp.49, 53).
w  WARNING indicator
  – Lights red light when the projector detects an abnormal 
condition.
  – Blinks red when the internal temperature of the 
projector exceeds the operating range (pp.44, 53).
u  OK button
 Execute the item selected or use it to access the...