Sanyo Projector Plv Hd150 User Manual

READYLAMP
LAMP
REPLACEWARNING
TEMP.
41
AIR FILTER CARE AND CLEANING
Turn power off, and disconnect AC power cord from AC outlet.1
2
Air Filter prevents dust from accumulating on surface of Projection Lens and Projection  Mirror.  Should Air Filter
become clogged with dust particles, it will reduce Cooling Fans effectiveness and may result in internal heat
build up and adversely affect life of a projector. Clean Air Filter following steps below: 
3
4
RECOMMENDATION
We recommend avoiding dusty/smoky...

42
LAMP MANAGEMENT
This Projector is equipped with 4 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp
Management Function. Lamp Management Function detects status of all lamps and shows status on screen or on LAMP
REPLACE indicator. This function also automatically controls Lamp Mode when any of lamps is out for end of life or
malfunctions. 
Projection Lamp lights normally.
Lamp Replace Indicator
This LAMP REPLACE indicator lights yellow when any of Projection Lamps is...

43
APPENDIX
Check number of lamp to be replaced on Lamp Status Display.
Remove two screws on Lamp Cover and press button to open
Lamp Cover. (See right figure.)
1
3
Loosen two screws and pull out Lamp Assembly to be replaced
by grasping handle.4
Turn off a projector and disconnect AC Power Cord. Allow a
projector to cool down for at least 45 minutes.2
Replace Lamp Assembly with a new one and tighten two screws.
Make sure Lamp is set properly
6
Follow these steps to replace lamp assembly.
Replace Lamp...

44
APPENDIX
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper
handling may result in accidents, injury, or create a fire hazard.
Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE...

45
Check audio cable connection from audio input source.
Adjust audio source.
Press VOLUME (+) button.
Press MUTE button.
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section CONNECTING
PROJECTOR  on pages 12 ~ 15.
2. Check cable connection.  Verify that all computer, video and power cord are properly connected.
3. Verify that all power is...

46
APPENDIX
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.
You can often correct operating problems yourself. If a projector fails to work properly, see TROUBLESHOOT-
ING section on pages 45-46. To correct failure, try Solutions.
If after following all operating instructions, you find that service is necessary, contact Sanyo Service Station or
store where you purchased unit.
Give model number and explain difficulty. We will advise you how to obtain...

47
APPENDIX
INDICATORS AND PROJECTOR CONDITION
Check the Indicators for projector condition.  
• • • on : red• • • dim• • • off• • • flashing : red
✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow.  When this indicator lights yellow,
replace the projection lamp with a new one promptly.  Reset the Lamp Replace Counter after replacement of the lamp.  
The projector is OFF.  (The MAIN switch OFF position or the
AC Power Cord is unplugged.)
The projector is...

48
APPENDIX
SDI 1SYSTEM
Input 2
Y, Pb/Cb, Pr/Cr
SYSTEM
3)
1)
Input 1
RGB 
Input
2)System
System
SVGA 3
Custom
SVGA 1
SVGA 2
Auto PC Adj.
Fine sync
Total dots
Horizontal
Vertical
Current mode
Clamp
Display area
Display area H
Display area V
Store
Quit
0 - 31
Display adjust
720 x 400
800 x 600
1024 x 768
1152 x 864
1280 x 720
1280 x 1024
Quit
1600 x 1200
Yes/No
1)
1080i/50
1035i
Auto
1080i/60
575p
480p
720p
575i
Mode 1 ~ Mode 20
640 x 480
Reset
SYSTEM2)
Input 3RGB (Analog)
RGB (Scart)
SYSTEM1)
RGB (PC...

49
APPENDIX
Lamp 2
Sound
Mute
Quit
Volume
Built-in SP.On/Off
On/Off
0 - 63
LanguageSettingEnglish
German
French
Italian
Spanish
Portuguese
Dutch
Swedish
Chinese
Korean
Japanese
On/Off
On/Off
On/Off
Off/Ready/Shut down
On/Off
4 Lamp/2 Lamp
Lamp 1
Menu position
Power management
On start
Lamp mode
Remote control code
Lamp counter reset
Code 1
Code 3
Code 4
Code 5
Code 6
Code 7
Code 8
Quit
Quit
Russian
Logo
Control panel
Key lock
Remote control
Off
Yes/NoFactory default
Blue backOn/Off
Display
Rear
Code 2...

50
APPENDIX
Owner’s Manual
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
DVI-VGA Cable and DVI Cable
MAC/VGA Adapter
6 Types Light-Block Sheet (For option lens)
2 Types Lens Attachment (For option lens)
Protective Dust Cover
TECHNICAL SPECIFICATIONS
1.65 TFT Active Matrix type, 3 panels
Multi-media Projector
83.9 lbs (38 kg)
22.9 x 10 x 30.9 (581 mm x 252 mm x 783 mm) 
1920 x 1080 dots
6,220,800 (1920 x 1080 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and...