Sanyo Projector Plv 30 User Manual

31
VIDEO MODE
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to select
SCREEN  and press the SELECT button.  Another dialog
box PICTURE SCREEN ADJUSTMENT DISPLAY will appear. 
Press the POINT DOWN button and a red-arrow icon will
appear.  Move the arrow to the screen size that you want to set,
and then press the 
SELECT...

32
SETTING
SETTING MENU
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to select
SETTING  and press the SELECT button.  Another dialog
box SETTING Menu will appear. 
Press the POINT DOWN button and a red-arrow icon will
appear.  Move the arrow to the item that you want to set, and
then press the 
SELECT button to set it On or Off or press the
POINT LEFT/RIGHT button to adjust the value.  
1
2
Blue back
When this function is “On,” this projector will produce...

33
The Lamp age function is designed to reset the lamp replacement
monitor timer.  When replacing the lamp, reset the lamp replacement
monitor timer by using this function.  (Refer to page 35.)
Lamp age
SELECTING LANGUAGE
Press the MENU button and the ON-SCREEN MENU will
appear.  Press POINT LEFT/RIGHT buttons to select
LANGUAGE  and press the SELECT button.  Another dialog box
LANGUAGE Menu will appear. 
Press the POINT DOWN button and a red-arrow icon will
appear.  Move the arrow to the language that...

34
APPENDIX
CLEANING THE PROJECTION LENS
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.  Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
When the projector is not in use, replace the lens cover.
1
3
Lightly wipe the cleaning cloth over the lens.2
Follow these steps to clean the projection lens:
MAINTENANCE
TEMPERATURE WARNING INDICATOR
The TEMPERATURE WARNING Indicator flashes red when the internal...

35
APPENDIX
LAMP REPLACEMENT
When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow.
When the image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is
required.
Turn off the projector and disconnect the AC plug.  Allow the
projector to cool for at least 45 minutes.
Remove the two screws with a screwdriver and pull out the
Lamp Assembly by grasping the handle.
1
3
LAMP REPLACEMENT MONITOR TIMER
Replace the Lamp Assembly...

36
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check the matters below once again.
1. Make sure you have connected the projector to your equipment as described in the section CONNECTING
THE PROJECTOR  on pages 11 ~ 13.
2. Check cable connection.  Verify that all computer, video and power cords are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not produce an image, re-start the computer.
5. If the image sill does not...

37
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc.  It is designed and manufactured to meet rigid U.L. safety standards
against risk of fire, casualty and electrical hazards.
APPENDIX
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
If the problem still persists after following all operating instructions,
contact the sales dealer where you
purchased the projector or the service center.Give the model number and...

38
APPENDIX
0.7” TFT Active Matrix type, 3 panels
TECHNICAL SPECIFICATIONS
Multi-media Projector
5.51 lbs (2.5 kg)
7.44” x 2.93” x 11.42” (189mm x 74.5mm x 290mm) (not including Adjustable Feet and Lens)
800 x 600 dots
1,440,000 (800 x 600 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 80 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 30” to 200”
500 TV lines
1 speaker, 1.57” x 1.18” (40mm x 30mm) 
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Owner’s Manual
AC Power Cord...

39 

Printed in Japan
Part No. 610 291 0056 (1AA6P1P2420A- M4GA-A)
SANYO Electric Co., Ltd