Sanyo Projector Plc Xw60 User Manual

51
SettingSetting
Power management
For  reducing  power  consumption  as  well  as  maintaining 
the lamp life, the Power management function turns off the 
projection lamp when the projector is not used for a certain 
period.
When  the  input  signal  is  interrupted  and  no  button  is 
pressed  for  more  than  30  seconds,  the  timer  display  with 
"No  signal"  appears.    The  countdown  starts  to  turn  off  the 
lamp.
Select one of the operations:
 Ready ........  W
hen  the  lamp...

5
Setting
Remote control
This projector provides two different remote control codes: 
the  factory-set  initial  code  (Code  1)  and  the    secondary 
code  (Code  2).    This  switching  function  prevents  remote 
control  interference  when  operating  several  projectors  or 
video equipment at the same time.
W h e n  o p e r a t i n g  t h e  p r o j e c t o r  i n  " C o d e  2 " ,  b o t h  t h e 
projector  and  the  remote  control  must  be  switched  to 
"Code 2".
To...

5
SettingSetting
Key lock
Security (Key lock and PIN code lock settings)
This  function  allows  you  to  use  Key  lock  and  PIN  code 
lock function to set the security for the projector operation.
This  function  locks  operation  of  the  top  control  or  the 
remote control.
It  is  useful  to  prevent  operation  by  an  unauthorized 
person....... not locked.
......  l
ock  the  operation  of  the  top 
control.    To  unlock,  use  the 
remote control.
......  lock 
the  operation  of  the...

54
Setting
To Enter the PIN code
Select  a  number  by  pressing  the  Point ed  buttons.  And 
then  press  the  Point 8  button  to  fix  the  number  and  move 
the  pointer.    The  number  changes  to  " ✳".    If  you  fixed 
an  incorrect  number,  move  the  pointer  to  the  number 
you  want  to  correct  by  pressing  the  Point 
7  button,  and 
then  select  the  correct  number  by  pressing  the  Point ed 
buttons.
Repeat this step to complete entering a four-digit number. 
After...

55
SettingSetting
This  function  provides  the  following  alternatives  in  the 
cooling fans' operation after turning off the projector. (p.20)
 
 L1
......  normal operation
  L2
......  s lower  and  lower-sound  than  the  normal 
operation  (L1),  but  it  takes  longer  to  cool  the 
projector down.
✔ Note:
   Setting  “Fan  control”  to  On1  or  On2  affects  L2 
operation in “Fan.”  Fan
This projector provides Fan control function in the Setting 
menu.
Choose the running speed of cooling...

56
Maintenance and Cleaning
This  function  is  used  to  reset  the  lamp  replacement 
counter.    When  replacing  the  projection  lamp,  reset  the 
lamp  replacement  counter  by  using  this  function.    See 
page 62 for operation.Lamp counter 
Factory default
This  function  returns  all  setting  values  except  for  the  user 
logo,  PIN  code  lock,  Logo  PIN  code  lock,  and  the  lamp 
counter to the factory default settings.
Exit the Setting Menu.
Quit
Closed Caption
Closed  Caption  is...

57
Maintenance and Cleaning
The WARNING indicator shows the state of the function which protects the projector. Check the state of the 
WARNING indicator and the POWER indicator to take proper maintenance.
Warning indicator
T h e   p r o j e c t o r   i s   s h u t   d o w n   a n d   t h e   WA R N I N G 
indicator is blinking red .
When  the  temperature  inside  the  projector  reaches  a 
certain  level,  the  projector  is  automatically  shut  down  to 
protect  the  inside  of  the  projector....

58
Maintenance and Cleaning
Turn  off  the  projector,  and  disconnect  the  AC  power 
cord from the AC outlet.
Remove the air filter by pulling the latch horizontally.
Air  filter  prevent  dust  from  accumulating  on  the  optical  elements  inside  the  projector.    Should  the  air  filter 
become clogged with dust particles, it will reduce cooling fans' effectiveness and may result in internal heat 
build up and adversely affect the life of the projector.  Clean the air filter following the...

5
Maintenance and CleaningMaintenance and Cleaning
Cleaning the Projector Cabinet
Softly  wipe  the  projector  body  with  a  soft,  dry  cleaning 
cloth.  When it is heavily soiled, use a small amount of 
mild detergent and finish with a soft, dry cleaning cloth.  
Avoid using an excessive amount of cleaner.  Abrasive 
cleaners,  solvent,  or  other  harsh  chemicals  might 
scratch the surface.
Follow these steps to clean the projector cabinet.
When  the  projector  is  not  in  use,  put  the...

60
Maintenance and Cleaning
When the life of the projection lamp of this projector draws 
to  an  end,  the  LAMP  REPLACE  indicator  emits  a  yellow 
light.  If this indicator lights yellow, replace the lamp with a 
new one promptly.
Lamp Replacement
Top Control
T h i s  i n d i c a t o r  i s  y e l l o w 
w h e n   t h e   l i f e   o f   t h e 
projection  lamp  draws  to 
an end.
For  continued  safety,  replace  with  a  lamp  of  the  same  type.    Do  not  drop  a  lamp  or  touch  a  glass...