Sanyo Projector Plc Xu88 User Manual

1

Installation
16
The preparation display will disappear 
after 30 seconds.
(See page 52 for Lamp control status.)
Lamp control status
Turning On the Projector
Connect  the  projector ’s  AC  power  cord  into  an  AC 
outlet. The  POWER  indicator  lights  red. Open  the  lens 
cap (see pages 9,59).
Press  the  POWER  ON/SYAND-BY  button  on  the  top 
control  or    on  the  remote  control. The  POWER  indicator 
lights  green  and  the  cooling  fans  start  to  operate.  The 
preparation...



TO  MAINTAIN  THE  LIFE  OF  THE  LAMP, 
ONCE  YOU  TURN  THE  PROJECTOR  ON, 
WAIT  AT  LEAST  FIVE  MINUTES  BEFORE 
TURNING IT OFF.
“Power off?” disappears after 4 seconds.
Turning Off the Projector
Press  the  POWER  ON/STAND-BY  button  on  the  top 
control  or  on  the  remote  control,  and  “Power  off?” 
appears on the screen.
Press the POWER ON/STAND-BY button again to turn 
off  the  projector.  The  POWER  indicator  starts  to  blink 
red, and the cooling fans keep running....



Basic OperationBasic Operation
How to Operate the On-Screen Menu
The  projector  can  be  adjusted  or  set  via  the  On-Screen 
Menu.  For  each  adjustment  and  setting  procedure,  refer  to 
the respective sections in this manual.
Use  the  Point◄►  buttons  to  select  a  Menu  icon.  Use 
the Point ▲▼ buttons to select an item in the selected 
menu.
Press  the  SELECT  button  to  show  the  item  data.  Use 
the Point ◄► buttons to adjust the values.
To close the On-Screen Menu,...



Menu Bar
PC System Menu
Image Adjust Menu
Used to adjust computer image 
[Contrast/Brightness/ Color 
temp./White balance (R/G/B)/
Sharpness/Gamma] (pp.36–37).
Setting Menu
Used to adjust 
the volume or 
mute the sound 
(p.26).
Image Select Menu
Used to select an 
image mode among 
Dynamic, Standard, Real, 
Blackboard(Green), and 
Image 1– 4 (p.35).
For computer source
AV System Menu
Used to select 
system of selected 
video source (p.41).
Image Adjust Menu
U s e d   t o   a d j u s t   p i...

5

Basic OperationBasic Operation
Rotate the Zoom Lever to zoom in and out.  
Rotate the Focus Ring to adjust the focus of the image.  
Zoom and Focus Adjustment
If  a  projected  picture  still  has  keystone  distortion  after 
pressing  the  AUTO  SETUP/CANCEL  button  on  the  top 
control  or  the  AUTO  SET/CANCEL  button  on  the  remote 
control, correct the image manually as follows:
Press the KEYSTONE button on the remote control. The 
Keystone dialog box appears. Use the Point ▲▼ buttons...

6

Sound Adjustment
1

Press the MENU button to display the On-Screen Menu. 
Use the Point ◄► buttons to move the red frame pointer 
to the Sound Menu icon.
Press  the  VOLUME+/–  buttons  on  the  top  control  or  on  the 
remote  control  to  adjust  the  volume. The  volume  dialog  box 
appears on the screen for a few seconds.
Press the MUTE button on the remote control to temporarily 
turn  off  the  sound.  To  turn  the  sound  back  on,  press  the 
MUTE button  again  or  press  the...

7

Basic OperationBasic Operation
Remote Control Operation
Using the remote control for some frequently used operations is advisabl\
e. Just pressing one of the buttons 
enables you to make the desired operation quickly without calling up the\
 On-Screen Menu.
Press  the  COMPUTER,  VIDEO,  or  NETWORK  button  on 
the remote control to select the input source. See pages 29-
30, 39-40 for details.
Refer to the owner’s manual “Network Set-up and 
Operation” for details about the network input....

8

Basic Operation
black out → the captured image → normal → • • • • •
Press  the  NO  SHOW  button  on  the  remote  control  to  black  out 
the  image.  To  restore  to  normal,  press  the  NO  SHOW  button 
again  or  press  any  other  button.  When  a  projected  image  is 
captured and set as “User” in the Logo selection (see page 48), 
the screen changes each time you press the NO SHOW button 
as follows.
NO SHOw button
Press  the  P-TIMER  button  on  the  remote  control.  The  P-Timer...

9

Basic Operation
Choose  either  Computer  1  (Analog)  or  Computer  2  by 
pressing  the  INPUT  button  on  the  top  control  or  press  the 
COMPUTER button on the remote control.
Before  using  these  buttons,  correct  input  source  should  be 
selected through Menu operation as described below.
Press  the  MENU  button  to  display  the  On-Screen 
Menu.  Use  the  Point ◄►  buttons  to  move  the  red 
frame pointer to the Input Menu icon.
1Input Menu
Use  the  Point ▲▼  buttons  to...

0

Computer Input
Choose  Computer  1(Digital)  by  pressing  the  INPUT  button 
on  the  top  control  or  press  the  COMPUTER  button  on  the 
remote control.
Before using these buttons, correct input source should be 
selected through Menu operation as described below.
Press  the  MENU  button  to  display  the  On-Screen 
Menu.  Use  the  Point ◄►  buttons  to  move  the  red 
frame pointer to the Input Menu icon.
1
Input MenuUse  the  Point ▲▼  buttons  to  move  the  red  arrow 
pointer...