Sanyo Projector Plc Xu75 User Manual

							
61

Appendix
Check the indicators for projector condition.
Indicators and Projector Condition
The projector is off. (The AC power cord is unplugged.)
The  projector  is  preparing  for  stand-by  or  the  projection lamp  is  being  cooled  down.    The  projector  cannot  be turned on until cooling is completed.
T h e  t e m p e r a t u r e  i n s i d e  t h e  p r o j e c t o r  i s  a b n o r m a l l y high.  The  projector  cannot  be  turned  on.    When  the projector  is  cooled  down  enough  and  the  temperature returns  to  normal,  the  POWER  indicator  lights  red  and the  projector  can  be  turned  on.  (The  WARNING  TEMP.indicator keeps blinking.)  Check and clean the air filters.
Projector Condition
The  projector  is  ready  to  be  turned  on  with  the  POWER ON/STAND-BY  button.
POWER
red/green
Indicators
LAMP REPLACE
yellow
WARNING  TEMP. 
red
The  projector  detects  an  abnormal  condition  and  cannot be  turned  on.    Unplug  the  AC  power  cord  and  plug  it again  to  turn  on  the  projector.    If  the  projector  is  turned off again, disconnect the AC power cord and contact the dealer  or  the  service  center  for  service  and  checkup. Do  not  leave  the  projector  on.    It  may  cause  an  electric shock or a fire hazard.
✽
✽
✽
✽
✽
The projector is operating normally.
The projector is in the Power management mode. 
✽
✽
The  projector  has  been  cooled  down  enough  and  the temperature  returns  to  normal.    When  turning  on  the projector,  the  WARNING  TEMP.  indicator  stops  blinking.  Check and clean the air filters.
• • • green• • • red• • • off
• • • blinks green
✽  When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When  this  indicator  lights  yellow,  replace  the  projection  lamp  with  a  new  one  promptly.    Reset  the lamp replacement counter after replacing the lamp.  See pages 55 and 56.\
• • • blinks red 
						

							
62

Appendix
Compatible Computer Specifications
Basically  this  projector  can  accept  the  signal  from  all  computers  with  the  V,  H-Frequency  below mentioned and less than 140 MHz of Dot Clock.  When selecting these modes, PC adjustment can be limited.
MAC LC13640 x 48034.9766.60MAC 13640 x 48035.0066.67
MAC 1683  x 6  449.774.55
MAC 1910 4 x 76860. 475.08
SVGA 1800 x 60035.15656. 5SVGA  800 x 60037.8860.3SVGA 3800 x 60046.87575.00SVGA 4800 x 60053.67485.06SVGA 5800 x 60048.087 .19SVGA 6800 x 60037.9061.03SVGA 7800 x 60034.5055.38SVGA 8800 x 60038.0060.51SVGA 9800 x 60038.6060.31
SVGA 11800 x 60038.0060.51
XGA 1010 4 x 768XGA 1110 4 x 768XGA 1 10 4 x 768XGA 1310 4 x 768
6 .0477.07
XGA 1410 4 x 768
61.0075.70
XGA 1510 4 x 768
35.5 86.96(Interlace)46.9058. 0
XGA 810 4 x 768
47.0058.30
XGA 910 4 x 768
58.037 .00
63.4879.3536.0087.17(Interlace)
SXGA 71 80 x 10  4
SXGA 101 80 x 960
81.1376.107
60.0060.00
XGA 110 4 x 768
XGA 410 4 x 768
48.3660.00
XGA 610 4 x 768XGA 710 4 x 768
56.47670.07
48.5060.0 44.0054.58
SXGA 81 80 x 10  4SXGA 91 80 x 10  463.9860.079.97675.0 5
XGA 510 4 x 76860.3174.9 
VGA 7640 x 48043. 6985.00
575i––––––––15.6 550.00(Interlace)480i––––––––15.73460.00(Interlace)
SXGA 1 115  x 90071.4075.60SXGA 11115  x 90061. 065. 0
SVGA 10800 x 6003 .7051.09
SXGA 131 80 x 10  450.0086.00(Interlace)
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq .(kHz)V-Freq .(Hz)VGA 1640 x 48031.4759.88VGA 7 0 x 40031.4770.09VGA 3640 x 40031.4770.09VGA 4640 x 48037.8674.38VGA 5640 x 48037.867 .81VGA 6640 x 48037.5075.00
SXGA 1115   x 86464. 070.40
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq .(kHz)V-Freq .(Hz)
SXGA 41 80 x 10  463.3459.98SXGA 51 80 x 10  4SXGA 61 80 x 10  463.7460.0171.6967.19
SXGA 1 80 x 10  46 .5058.60SXGA 31 80 x 10  463.9060.00
XGA 10 4 x 76868.67784.997XGA 310 4 x 76860.0  375.03
SXGA 181 80 x 10  446.4386.70(Interlace)SXGA 191 80 x 10  463.7960.18
SXGA 141 80 x 10  4SXGA 151 80 x 10  4SXGA 161 80 x 10  4SXGA 17115  x 900
50.0094.00(Interlace)63.3760.0176.977 .0061.8566.00
MAC1 80 x 96075.0075.08MAC1 80 x 10  4480p––––––––575p––––––––
80.0075.0831.4759.88
1080i––––––––
31. 550.00
33.7560.00(Interlace)
7 0p––––––––1035i––––––––45.0060.0033.7560.00(Interlace)
1080i––––––––8.1  550.00(Interlace)
 SXGA +11400 x 105063.97960.190
MAC 1115  x 87068.6875.06
WXGA  1360 x 768WXGA 31376 x 768WXGA 41360 x 768
47.7060.0048.3660.0056.167 .00
WXGA 11366 x 768
UXGA 41600 x 1  0093.7575.00
UXGA 11600 x 1 00UXGA 1600 x 1  00UXGA 31600 x 1 00
75.0060.0081. 565.0087.570.00
48.3660.00
 SXGA + 1400 x 105065.34660.116 SXGA +31400 x 105065.1 159.90
SXGA   01 80 x 10  491.14685.0 4
Appendix
WXGA 61 80 x 768WXGA 71 80 x 768WXGA 81 80 x 768
47.77659.8760.  8974.89368.63384.837 
						

							
63

Appendix
Technical Specifications
Mechanical Information Projector Type   Multi-media Projector 
 
Dimensions (W x H x D)
 
335 mm x 83 mm x 

38.4 mm (Not including adjustable feet) 
 
Net Weight
 
6.63lbs (3.0 kgs) 
	 Feet
	
Adjustment	 0˚
	
to
	
10.0˚  Panel Resolution  LCD Panel System   0.63" TFT Active Matrix type, 3 panels 
 
Panel Resolution
 
1,0

4 x 768 dots 
 
Number of Pixels
  
,359,

96 (1,0

4 x 768 x 3 panels)  Signal Compatibility  Color System   PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N 
 
High Definition TV Signal
 
480i, 480p, 575i, 575p, 7

0p, 1035i, and 1080i 
 
Scanning Frequency
 
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz  Optical Information  Projection Image Size (Diagonal)   Adjustable from 40" to 300"      
  Projection Lens   F 1.65 ~ 1.81 lens with f   .5 mm ~   7 mm with manual zoom and focus 
 
Throw Distance
 
4.6' ~ 41.3' (1.4 m ~ 1

.6 m) 
 
Projection Lamp
 
PLC-XU75: 

00W 
                           
 
PLC-XU78: 

0W
  Interface  Video Input Jack   RCA Type x 1  
 
S-Video Input Jack
 
Mini DIN 4 pin x 1 
 
Audio Input Jacks
 
RCA Type x 
  Computer Input 1/Component Input Terminal  Analog RGB (Mini D-sub 15 pin) Terminal x 1  Computer Input   /Monitor Output Terminal Analog RGB (Mini D-sub 15 pin) Terminal x 1 (In/Out switchable)  Computer/ Component Audio Input Jack  Mini Jack (stereo) x 1 
 
Service Port Connector
 
Mini DIN 8 pin x 1 
 
Audio Output Jack
 
Mini Jack (stereo) x 1 (Variable)  Audio  Internal Audio Amp   1.0 W RMS 
 
Built-in Speaker
 
1 speaker, ø1.1" (  8 mm)   Power Voltage and Power Consumption   AC 100 ~ 1  0 V (3.  A Max. Ampere), 50/60 Hz (The U.S.A and Canada) 
   
AC 

00 ~ 

40 V (1.6A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)  Operating Environment	 Operating 	 Temperature	 41˚F 	 ~ 	 95˚F 	 (5˚C 	 ~ 	 35˚C) 
	 Storage
	
Temperature	 14˚F
	
~
	
140˚F
	
(-10˚C
	
~
	
60˚C)  Remote Control  Battery   AA or LR6 1.5 V ALKALINE TYPE x   
	 Operating
	
Range	 16.4'
	
(5
	
m)/±30˚ 
 
Dimensions
 
1.9" (W) x 0.87" (H) x 5.7" (D) (49 mm x    mm x 145.3 mm) 
 
Net Weight
 
3.53 oz (100 g) (including batteries) 
						

							
64

Appendix
Accessories Owner's Manual (CD-ROM)
 
Quick Reference Guide 
 
AC Power Cord 
 
Remote Control and Batteries 
 
VGA Cable 
 
Lens Cover with String  
 
PIN Code Label
   Lamp Replacement Label
 
● The specifications are subject to change without notice.● LCD  panels  are  manufactured  to  the  highest  possible  standards.    Even  though  99.99%  of the  pixels  are  effective,  a  tiny  fraction  of  the  pixels  (0.01%  or  less)  may  be  ineffective  by  the characteristics of the LCD panels.
    Model No.
COMPONENT-VGA Cable  : POA-CA-COMPVGA 
SCART-VGA Cable  : POA-CA-SCART 
Laser Pointer Remote Control  : POA-RCKIT03 
Presentation Kit  : POA-RCKIT04
Soft Carrying Case  : POA-CAC-VCL  
 
The  parts  listed  below  are  optionally  available.    When  ordering  those  parts,  specify  the  item  and Model No. to the sales dealer.
Optional Parts
Appendix 
						

							
65

Terminal: Mini DIN 8-PIN
1345876
SERVICE PORT CONNECTOR
COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL (ANALOG)
Terminal : Analog RGB (Mini D-sub 15 pin)
512341096781514131112
Configurations of Terminals
Red (R/Cr) Input/Output
Ground (Horiz.sync.)
Green (G/Y) Input/Output
-----
Blue (B/Cb) Input/Output
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
5V
Horiz. sync. Input/Output (Composite H/V sync.)
Ground (Vert.sync.)
DDC data
Ground/-----
Vert. sync.
DDC clock
9
13
10
1
11
14
15
Serial
GND
R X D
-----
-----
RTS/CTS
T X D
GND
4
1
3
2
5
6
7
GND8
Appendix
Dimensions
Unit: inch(mm)
Screw Holes for Ceiling MountScrew: M4Depth: 0.394(10.0) 
						

							
66
Appendix
Write  down  the  PIN  code  number  in  the  column  below  and  keep  it  with  this  manual  securely.  If  you forgot or lost the number and unable to operate the projector, contact the service station. 
PIN Code Number Memo
Factory default set No: 1 2 3 4*
*   Should  the  four-digit  number  be 
changed,  the  factory  set  number will be invalid.
PIN Code Lock No.
Logo PIN Code Lock No.
Factory default set No: 4 3 2 1*
While the projector is locked with the PIN code....
Put the label below (supplied) on in a prominent place of the projector's body while it is locked with a PIN code.
When  using  the  projector  ceiling-mounted,  put  the  Lamp replacement  label  (supplied)  on  in  a  prominent  place  of the  projector's  body  to  check  the  Replacement  Lamp Type Number.
Lamp Replacement Label
Lamp Replacement Label 
						

							
KH3ACSANy O Electric Co  . , Ltd  .