Sanyo Projector Plc Xu21n User Manual

31
SETTING
SETTING MENU
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to select
SETTING  and press the SELECT button.  Another
dialog box SETTING Menu will appear. 
Press the POINT DOWN button and a red-arrow icon will
appear.  Move the arrow to the item that you want to set, and
then press the 
SELECT button to set it On or Off.  
1
2
Blue backWhen this function is in the On position, this projector
will produce a blue image instead of the video noise on...

32
APPENDIX
OPERATING WIRELESS MOUSE
INSTALLATION
The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless mouse
for most Personal Computers.  The POINT buttons and the two CLICK buttons are used for the wireless mouse
operation.
The wireless mouse is usable when PC mouse pointer is displayed on the screen.  When the menu or the
indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse cannot
be used.
Connect...

33
APPENDIX
CLEANING THE PROJECTION LENS
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.  Avoid using an excessive amount of
cleaner.  Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
When you dont use the projector, replace the lens cover.
1
3
Lightly wipe the cleaning cloth over the lens.2
Follow these steps to clean the projection lens:
MAINTENANCE
TEMPERATURE WARNING INDICATOR
The TEMPERATURE WARNING Indicator flashes red when the internal...

34
APPENDIX
LAMP REPLACEMENT INDICATOR
When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights
yellow.  When the image becomes dark or the color of the image become unnatural, replacement of the Lamp
is required.
Turn off the projector and disconnect the AC plug.  Allow the
projector to cool for at least 45 minutes.
Remove 2 screws with a screwdriver and pull out the Lamp
Assembly by grasping the handle.
1
3
LAMP REPLACEMENT MONITOR TIMER
Replace the Lamp...

35
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service station for assistance, check the matters below once again.
1. Make sure you have connected the projector to your equipment a s described in section CONNECTING THE
PROJECTOR  on pages 10 ~ 13.
2. Check cable connection.  Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not produce the image, re-start the computer.
5. If the image sill does not...

36
APPENDIX
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
Remote Control Unit
does not work.Check the batteries.
Check the ALL-OFF switch on the Remote Control Unit is set to “ON.”.
Make sure nothing is between the Remote Receiver and the Remote Control Unit.
Make sure you are not too far from the projector when using the Remote Control Unit.
Maximum operating range is 16.4’ (5m).
Problem:Try these Solution
Wireless Mouse
function does not...

37
0.9 TFT Active Matrix type, 3 panels
TECHNICAL SPECIFICATIONS
Multi-media Projector
8.6 lbs (3.9 kg)
9.41 x 3.54 x 12.72 (239mm x 90mm x 323mm) (not including Adjustable Feet)
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 30” to 300”
800 TV lines
1 speaker, 1.57 x 1.18 (40mm x 30mm) 
AC 100 ~ 120 V, 50 / 60 Hz
2.5 A (Max. Ampere) 
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)...

38
OPTIONAL PARTS
The parts listed below are optionally supplied.  When ordering those parts, give the
name and the Type No. of it to the sales dealer.
Control Cable for Serial Type No. : POA-MCSRL
Control Cable for ADB Type No. : POA-MCMAC
MAC Adapter Type No. : POA-MACAP 

Printed in Japan
Part No. 610 291 5885 (1AA6P1P2705-- MB6AC)
SANYO Electric Co., Ltd