Sanyo Projector Plc Xc50 User Manual

71
   Appendix
Indicators and Projector Condition
Check the indicators for the projector condition.  
The projector is operating normally  .
The projector is off. (The AC power cord is unplugged.)
The  projector  is  in  stand-by  mode.  Press  the  POWER ON/STAND-BY button to turn on the projector.
Projector ConditionPOWERred/green
Indicators
LAMP REPLACEyellow
WARNING
TEMP  . 
red
The filter is scrolled using the Filter control function in the setting menu.When  the  filter  is  being  scrolled,  the...

7

AppendixAppendix
The projector has been cooled down enough and thetemperature  returns  to  normal.  When  turning  on  the projector,  the  WARNING  TEMP.  indicator  stops  blinking. Check and replace the filter.
Projector ConditionPOWERred/green
Indicators
LAMP REPLACEyellow
WARNINGTEMP  . 
red
WARNING
FILTER orange

AnyThe lamp has been used overtime. Replace the lampimmediately and then reset the lamp counter. The indicator will be turned off after resetting the counter.
Any
If the...

7

Appendix
Compatible Computer Specifications
Basically  this  projector  can  accept  the  signal  from  all  computers  with  the  V,  H-Frequency  below  mentioned and less than 140 MHz of Dot Clock for Analog signal and 110 MHz of Dot Clock for digital signal.  When selecting these modes, PC adjustment can be limited.
MAC LC13640 x 48034.9766.60MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
MAC 191024 x 76860.2475.08
SVGA 1800 x 60035.15656.25SVGA 2800 x 60037.8860.32SVGA 3800 x...

74

Appendix
RESOLUTION
640 x 480
640 x 480
768 x 575
800 x 600
1366 x 768
ON-SCREEN DISPLA y
D-720p
D-1035i
D-1080i
D-1080i
1024 x 768
1360 x 768
1376 x 768
When the input signal is digital from DVI terminal, refer to the chart b\
elow.
Note:
 • When the input signal is D-SXGA 1, D-SXGA 2, D-SXGA 3,  or D-SXGA+1, images may not be displayed properly depending on computers.  • The specifications are subject to change without notice.
1360 x 768
1366 x 768
1280 x 768
1280 x 768
D-SXGA1
D-SXGA2
D-SXGA+1...

75

Appendix   Appendix
Technical Specifications
Mechanical Information
 Projector Type  Multi-media Projector 
  Dimensions (W x H x D)  410.0 mm x 85.0 mm x 262.8 mm  (Not including protrusions) 
  Net Weight  8.82lbs (4.0 kg) 
  Foot Adjustment  0˚ to 10.0˚  Panel Resolution
 LCD Panel System  0.63" TFT Active Matrix type, 3 panels 
  Panel Resolution  1,024 x 768 dots 
  Number of Pixels  2,359,296 (1,024 x 768 x 3 panels)  Signal Compatibility
 Color System  PAL, SECAM, NTSC, NTSC4.43, PAL-M,...

76

Appendix
Accessories Owner's Manual (CD-ROM)
  Quick Reference Guide 
  AC Power Cord 
  Remote Control and Batteries 
  VGA Cable 
  PIN Code Label
● The specifications are subject to change without notice.● LCD  panels  are  manufactured  to  the  highest  possible  standards.    Even  though  99.99%  of  the  pixels are effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
      Model No .COMPONENT-VGA Cable : POA-CA-COMPVGA...

77

CONTROL PORT CONNECTOR (D-sub  pin)
COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL (ANALOG)
Terminal : Analog RGB (Mini D-sub 15 pin)
512341096781514131112
Configurations of Terminals
Red (R/Cr) Input/R Output
Ground (Horiz.sync.)
Green (G/Y) Input/G Output
-----
Blue (B/Cb/---) Input/B Output
Ground (Red)
Ground (Green)
Ground (Blue)
1
5

4

6
7
8
5V / ---
Horiz. sync. Input/Output (Composite H/V sync.Input)
Ground (Vert.sync.)
DDC data / ---
Ground 
Vert. sync. Input/Output...

78

Appendix
Dimensions
8.60(218.5)(50.7)
2.17(55.0)
(410.0)5.91(150.2)
3.04(77.3)
3.52(89.4)
2.17(55.2)
10.35(262.8)
10.50(266.8)
3.35(85.0)4.04(102.7)4.38(111.2)
2.81(71.5)2.17(55.0)
(56.3)
(143.0)
(230.0)(50.0)
(50.8)(102.0)
(97.0)
(30.0)
1.97
16.14
Unit: inch (mm)
Screw Holes for Ceiling MountScrew: M4Depth: 0.47(12.0)
Appendix 

7

Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. 
PIN Code Number Memo
Factory default set No: 1 2 3 4*
*  Should  the  four-digit  number  be 
changed,  the  factory  set  number will be invalid.
PIN Code Lock No .
Logo PIN Code Lock No .
Factory default set No: 4 3 2 1*
While the projector is locked with the PIN code....
Put  the  label  below  (supplied)...

KK7ACSANyO Electric Co ., Ltd .