Sanyo Plc Xu45 Projector User Manual

41
APPENDIX
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
If the problem still persists after following all operating instructions,
contact the sales dealer where you purchased the
projector or the service center.Give the model number and explain about the problem.  We will advise you how to obtain
service.
Remote Control does
not work.Check the batteries.
Check ALL-OFF switch on the Remote Control is set to “ON.”
Make sure there is no obstructions...

42
APPENDIX
INDICATORS AND PROJECTOR CONDITION
Check the Indicators for projector condition.  
• • • on• • • dim• • • off• • • flashing
✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow.  When this indicator lights yellow,
replace the projection lamp with a new one promptly.  Reset the Lamp Replace Counter after replacement of the lamp.  
The projector is OFF.  (The AC Power Cord is unplugged.)
The projector is READY to be turned on with the POWER
ON-OFF...

43
APPENDIX
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140
MHz of Dot Clock.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
SVGA 1800 x 60035.15656.25
SVGA 2800...

44
APPENDIX
TECHNICAL SPECIFICATIONS
0.9 TFT Active Matrix type, 3 panels
Multi-media Projector
9.3 lbs (4.2 kg)
13.11 x 3.52 x 9.96 (333mm x 89.5mm x 253mm) (not including Adjustable Feet)
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 31” to 300”
1 speaker, 1.18 x 1.57 (30mm x 40mm) 
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Owner’s Manual
AC Power Cord
Remote Control and...

45
APPENDIX
CONFIGURATIONS OF TERMINALS
MONITOR OUT TERMINAL (ANALOG)
Terminal : HDB15-PIN 
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
+5V Power
Horiz. sync.
Ground (Vert.sync.)
DDC Data
Sense 0
Vert. sync.
DDC Clock
9
13
10
12
11
14
15
Pin Configuration
DVI-I TERMINAL (DIGITAL/ANALOG) 
1917
21018
31119
41220
51321
61422
71523
81624
C1
C2
C3
C5C4
Pin Configuration
Analog Red Input
Analog Ground (R/G/B)...

46
Terminal : Mini DIN 8-PIN
12
345876
Pin Configuration
CONTROL PORT CONNECTOR
-----
CLK
DATA
GND
-----
-----
GND
-----
R X D
-----
-----
GND
RTS / CTS
T X D
GND
GND
-----
ADB
-----
GND
-----
-----
-----
GND
PS/2SerialADB
1
2
3
4
5
6
7
8
Vcc
- Data
+ Data
Ground
1
2
3
4
USB CONNECTOR (Series B)
Pin Configuration
2
341
APPENDIX
OPTIONAL PARTS
The parts listed below are optionally supplied.  When ordering those parts, give the name and Type No. to the sales dealer.
Control Cable (Serial Port) Type No. :...

47 

Printed in Japan
Part No. 610 304 4804 (1AA6P1P3770-- ME3A) 
SANYO Electric Co., Ltd