Sanyo Plc Xu45 Projector User Manual

							41
APPENDIX
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
If the problem still persists after following all operating instructions,
contact the sales dealer where you purchased the
projector or the service center.Give the model number and explain about the problem.  We will advise you how to obtain
service.
Remote Control does
not work.Check the batteries.
Check ALL-OFF switch on the Remote Control is set to “ON.”
Make sure there is no obstructions between the projector and the Remote Control.
Make sure you are not too far from the projector when using the Remote Control.
Maximum operating range is 16.4’ (5m).
Make sure the code of the Remote Control is set to conform to the projector.
(See “SETTING” section on page 34, 35.)
Problem:Try these Solutions
Wireless Mouse
function does not
work.Check cable connection between the projector and your computer.
Check the mouse setting on your computer.
Turn the projector on before turning on the computer.
This symbol on the nameplate means the product is Listed by Underwriters Laboratories
Inc.  It is designed and manufactured to meet rigid U.L. safety standards against risk of
fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC). 
						

							42
APPENDIX
INDICATORS AND PROJECTOR CONDITION
Check the Indicators for projector condition.  
• • • on• • • dim• • • off• • • flashing
✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow.  When this indicator lights yellow,
replace the projection lamp with a new one promptly.  Reset the Lamp Replace Counter after replacement of the lamp.  
The projector is OFF.  (The AC Power Cord is unplugged.)
The projector is READY to be turned on with the POWER
ON-OFF button.
The projector is being cooled down. It cannot be turned on until
the READY indicator lights green.  
Projector Condition
The projector is operating normally. 
LAMP
REPLACE
yellow
Indicators
READYgreen
LAMPred
WARNING
TEMP.
red
The projector is in the Power management mode. 
✽
✽
✽
✽
The temperature inside the projector is abnormally high.  The
projector cannot be turned on.  When  the projector is cooled
down enough and the temperature returns to normal, the
READY indicator lights green and the WARNING TEMP. indi-
cator goes off.  Then the projector can be turned on. 
✽ 
						

							43
APPENDIX
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140
MHz of Dot Clock.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
SVGA 1800 x 60035.15656.25
SVGA 2800 x 60037.8860.32
SVGA 3800 x 60046.87575.00
SVGA 4800 x 60053.67485.06
SVGA 5800 x 60048.0872.19
SVGA 6800 x 60037.9061.03
SVGA 7800 x 60034.5055.38
SVGA 8800 x 60038.0060.51
SVGA 9800 x 60038.6060.31
SVGA 11800 x 60038.0060.51
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
XGA 81024 x 768
XGA 91024 x 768
63.4879.35
36.0087.17
(Interlace)
XGA 11024 x 768
XGA 21024 x 768
XGA 31024 x 768
XGA 41024 x 768
48.3660.00
68.67784.997
XGA 61024 x 768
60.02375.03
XGA 71024 x 768
56.47670.07
48.5060.02
44.0054.58
XGA 51024 x 76860.3174.92
VGA 7640 x 48043.26985.00
RGB––––––––15.73460
(Interlace)RGB––––––––15.62550
(Interlace)
SVGA 10800 x 60032.7051.09
XGA 101024 x 76862.0477.07
MAC 191024 x 76860.2475.08
MAC 211152 x 87068.6875.06
MAC1280 x 96075.0075.08
MAC1280 x 102480.0075.08
XGA 111024 x 768
XGA 121024 x 768
XGA 131024 x 768
XGA 141024 x 768
61.0075.70
XGA 151024 x 768
35.52286.96
(Interlace)
46.9058.20
47.0058.30
58.0372.00
SXGA 11152 x 864
SXGA 21280 x 1024
SXGA 31280 x 1024
SXGA 41280 x 1024
64.2070.40
SXGA 51280 x 1024
62.5058.60
SXGA 61280 x 1024
63.9060.00
SXGA 71280 x 1024
63.3459.98
SXGA 81280 x 1024
63.7460.01
SXGA 111152 x 900
71.6967.19
SXGA 121152 x 900
81.1376.107
SXGA 131280 x 1024
63.9860.02
SXGA 141280 x 1024
61.2065.20
71.4075.60
50.0086.00
(Interlace)
720p (HDTV)––––––––
50.0094.00
(Interlace)
45.0060.00
SXGA 91280 x 1024
SXGA 101280 x 960
79.97675.025
60.0060.00
SXGA 151280 x 1024
SXGA 161280 x 1024
SXGA 171152 x 900
SXGA 181280 x 1024
63.3760.01
76.9772.00
61.8566.00
46.4386.70
(Interlace)
SXGA 191280 x 102463.7960.18
1080i 60(HDTV)––––––––33.7560.00
(Interlace)1035i (HDTV)––––––––33.7560.00
(Interlace)
1080i 50(HDTV)––––––––28.12550.00
(Interlace)
NOTE : Specifications are subject to change without notice.
When an input signal is digital from DVI terminal, refer to the chart below.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
D-VGA640 x 48031.46959.940
D-SVGA800 x 60037.87960.317
D-XGA1024 x 76848.36360.004
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
D-SXGA 11280 x 1024
D-SXGA 21280 x 1024
D-SXGA 3  1280 x 1024
63.98160.020
60.27658.069
31.6529.8 
						

							44
APPENDIX
TECHNICAL SPECIFICATIONS
0.9 TFT Active Matrix type, 3 panels
Multi-media Projector
9.3 lbs (4.2 kg)
13.11 x 3.52 x 9.96 (333mm x 89.5mm x 253mm) (not including Adjustable Feet)
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 31” to 300”
1 speaker, 1.18 x 1.57 (30mm x 40mm) 
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Owner’s Manual
AC Power Cord
Remote Control and Batteries
Control Cable for PS/2 port 
DVI-VGA Cable
Carrying Bag
Lens Cover 
Projector Type
Net Weight
Dimensions (W x H x D)
Panel Resolution
Number of Pixels
Color System
Scanning Frequency
Projection Image size (Diagonal)
Built-in Speaker
Operating Temperature
Storage Temperature
Accessories
LCD Panel System
The specifications are subject to change without notice.
F 1.7 ~ 2.0 lens with f 37.4 mm ~ 48.3 mm with motor zoom and focus
5.3’ ~ 40.0’ (1.6 m ~ 12.2 m)
200 W
RCA Type  x 3 (Video/Y, Pb/Cb, Pr/Cr) and Mini DIN 4 pin x 1 (S-Video)
Projection Lens
Throw Distance
Projection Lamp
Video Input Jacks
RCA Type  x 2Audio Input Jacks
DVI-I Terminal (Digital/Analog)
Mini Jack (stereo)  x 1
Mini DIN 8 pin x 1
RCA Type  x 2
1.0 W RMS
Computer Input Terminal
Computer Audio Input Jack
Control Port Connector
Audio Output Jacks
Internal Audio Amp
0˚ to 15.6˚Feet Adjustment
Power Source : AA, UM3 or R06 Type x 2
Operating Range : 16.4’ (5m) / ±30˚
Dimensions : 2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
Net Weight : 0.36 lbs (165 g) (including batteries)
Laser Pointer : Class IILaser  
(Max. Output : 1mW / Wave length : 650±20nm)
Remote Control
480i, 480p, 575i, 575p, 720p, 1035i, and 1080iHigh Definition TV Signal
USB Series B receptacle x 1USB Connector
AC 100 ~ 120 V (3.6 A  Max. Ampere), 50 / 60 Hz  (The U.S.A and Canada)
AC 200 ~ 240 V (1.8 A  Max. Ampere), 50 / 60 Hz  (Continental Europe and The U.K.)
Voltage and 
Power Consumption
Monitor Out Terminal(VGA) HDB 15 Terminal x 1
LCD panels are manufactured to the highest possible standards.  Even though 99.99% of the pixels are effective,  a
tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels. 
The ON-SCREEN MENU and figures in this manual may differ slightly from the product.  800 TV lines
Horizontal Resolution 
						

							45
APPENDIX
CONFIGURATIONS OF TERMINALS
MONITOR OUT TERMINAL (ANALOG)
Terminal : HDB15-PIN 
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
+5V Power
Horiz. sync.
Ground (Vert.sync.)
DDC Data
Sense 0
Vert. sync.
DDC Clock
9
13
10
12
11
14
15
Pin Configuration
DVI-I TERMINAL (DIGITAL/ANALOG) 
1917
21018
31119
41220
51321
61422
71523
81624
C1
C2
C3
C5C4
Pin Configuration
Analog Red Input
Analog Ground (R/G/B)
Analog Green Input
Analog Horiz. sync
Analog Blue Input
C1
C5
C2
C4
C3
T.M.D.S. Data2–
W-LAN
T.M.D.S. Data2+
+3.3V MCI
T.M.D.S. Data2/4 Shield
DDC Clock
DDC Data
Analog Vert. sync
1
5
2
4
3
6
7
8
T.M.D.S. Data1–
Card In
T.M.D.S. Data1+
+5V MCI
T.M.D.S. Data1/3 Shield
+5V Power
Ground (for +5V)
Hot Plug Detect
9
13
10
12
11
14
15
16
T.M.D.S. Data0–
Viewer TXD
T.M.D.S. Data0+
Viewer RXD
T.M.D.S. Data0/5 Shield
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
17
21
18
20
19
22
23
24 
						

							46
Terminal : Mini DIN 8-PIN
12
345876
Pin Configuration
CONTROL PORT CONNECTOR
-----
CLK
DATA
GND
-----
-----
GND
-----
R X D
-----
-----
GND
RTS / CTS
T X D
GND
GND
-----
ADB
-----
GND
-----
-----
-----
GND
PS/2SerialADB
1
2
3
4
5
6
7
8
Vcc
- Data
+ Data
Ground
1
2
3
4
USB CONNECTOR (Series B)
Pin Configuration
2
341
APPENDIX
OPTIONAL PARTS
The parts listed below are optionally supplied.  When ordering those parts, give the name and Type No. to the sales dealer.
Control Cable (Serial Port) Type No. : POA-MCSRL
Control Cable (ADB Port) Type No. : POA-MCMAC
MAC Adapter Type No. : POA-MACAP
Media Card Imager Kit Type No. : POA-MD07MCI
Wireless Imager Kit Type No. :
Available models are different in each country.  Contact the
sales dealer for details.
When using Wireless Imager, set the following model name to
PJ Controller.
Model Name : 09-2-1 
						

							47 
						

							Printed in Japan
Part No. 610 304 4804 (1AA6P1P3770-- ME3A) 
SANYO Electric Co., Ltd