Sanyo Plc Xp30 Projector User Manual

21
BASIC OPERATION
ADJUSTING THE IMAGE
The message disappears after 4 seconds.
The message disappears after 4 seconds.
Zoom
Focus
ZOOM ADJUSTMENT
FOCUS ADJUSTMENT
1Press the ZOOM /button(s) on the Top Control or on the
Remote Control Unit.  The message “Zoom” is displayed.
2Press the ZOOM button or the POINT UP button to make the
image larger, and press the ZOOM button or the POINT
DOWN button to make the image smaller.
1Press the FOCUS /button(s) on the Top Control or on the
Remote Control Unit....

22
KEYSTONE ADJUSTMENT
1Press the  KEYSTONE /button on the Remote Control Unit
or select the Keystone on SCREEN MENU.  (Refer to page 31,
35.)  The message “Keystone” is displayed.
2Correct the Keystone distortion by pressing the KEYSTONE
/button or the POINT UP/DOWN button(s).  Press the
KEYSTONE button or the POINT UP button to reduce the
upper part or the image, and press the KEYSTONE button or
the POINT DOWN button to reduce the lower part.  
The message disappears after 4 seconds.
Reduce the...

23
BASIC OPERATION
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to select
SOUND and press the SELECT button.  Another dialog box
SOUND MENU will appear. 
Sound Volume Adjustment
Press the VOLUME (+/–) button(s) on the Top Control or on the
Remote Control Unit to adjust the volume.  The Volume dialog box
appears on the screen for a few seconds.
(+) button to increase the volume, and (–) button  decreasing.
Sound Mute Setting
Press the MUTE button on the...

24
COMPUTER button
COMPUTER MODE
SELECTING COMPUTER MODE
MENU OPERATION
When selecting the Computer Mode, the Current Mode display
appears to show the information of the computer being selected.  
CURRENT MODE DISPLAY
COMPUTER 1
COMPUTER 2
SELECTING COMPUTER SYSTEM
AUTOMATIC MULTI-SCAN SYSTEM
This projector automatically tunes to most different types of
computers based on VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATION” on page 25).
When selecting Computer, this projector...

25
COMPUTER MODE
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below and
less than 180 MHz of Dot Clock.
NOTE : Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x...

26
COMPUTER MODE
PC ADJUSTMENT
This Projector can automatically tune to the display signals from most personal computers currently distributed.
However, some computers employ special signal formats which are different from the standard ones and may
not be tuned by the Multi-Scan system of this projector.  If this happens, the projector cannot reproduce a proper
image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered
picture or a skewed picture.
This...

27
COMPUTER MODE
The number of the total vertical lines.  Adjust the number to match
the image of your personal computer.
Total lines
Recalls the parameter data that was previously
adjusted.Reset
Stores the parameters in the memory.Stored
Clears the parameter data previously set.Mode free
Closes PC ADJUST MENU.Quit
The number of the total dots in one horizontal period.  Adjust the
number to match the image of your computer.
Total dots
Adjustment of the horizontal or vertical picture position.  When the...

28
COMPUTER MODE
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to select IMAGE
and press the SELECT button.  Another dialog box IMAGE
MENU will appear. 
When selecting “,” the custom setting dialog box will appear.  Move
the arrow to the item that you want to change by pressing the POINT
UP/DOWN button, and adjust each value by pressing the SELECT
button to match with the image.
1
2
Adjust the picture as necessary to eliminate flicker from the display....

29
COMPUTER MODE
The normal picture level is preset on this projector at the
factory and can be restored anytime you press the NORMAL
button (located on the Top Control or on the Remote Control
Unit).  The “Standard” display will be displayed on the screen
for a few seconds. 
NORMAL FUNCTION
Standard
The Auto Image function is provided to automatically adjust Fine sync., Total dots, and Picture Position for most
computers.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT...

30
COMPUTER MODE
PICTURE POSITION ADJUSTMENT
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to select
POSITION and press the SELECT button.  The POSITION
MENU will appear. 1
2Select the arrow to the direction (described as  ,  ,  or  )
that you want to adjust by pressing the POINT UP/DOWN/
LEFT/RIGHT buttons, and then press the SELECT button.
Select the...