Sanyo Plc Xp30 Projector User Manual

11
ANALOG DIGITALCOMPUTER IN 1
COMPUTER IN 2
MONITOR OUT
AV INCONTROL PORT 1
CONTROL PORT 2R–AUDIO–LS–VIDEO
Y/VIDEOCb/Pb Cr/Pr
(MONO)
AUDIO 1
AUDIO 2
(STEREO)
(STEREO)
RGBH V
ANALOG DIGITALCOMPUTER IN 1
COMPUTER IN 2
MONITOR OUTAV INCONTROL PORT 1
CONTROL PORT 2R–AUDIO–LS–VIDEO
Y/VIDEO Cb/Pb Cr/Pr(MONO)AUDIO 1
AUDIO 2(STEREO)
(STEREO)
RESETR/C JACKR–AUDIO–LVIDEO
RGBH V
RGBH V
CONNECTING THE PROJECTOR
TERMINALS OF THE PROJECTOR
When controlling the computer
with the Remote Control of
this projector,...

MONITOR OUT
RESETR/C JACKR–AUDIO–LVIDEORGBH V
12
CONNECTING THE PROJECTOR
Connect an external audio
amplifier to these jacks.  
(Refer to P13, 14.)
AUDIO OUTPUT JACKS
This projector uses a micro processor to control the
unit.  Occasionally, the micro processor may
malfunction and need to be reset.  This can be done
by pressing the RESET button with a pen, which will
shut down and restart the unit.  Do not use the
RESET function excessively.
RESET BUTTON
When using the Wired / Wireless
Remote Control Unit...

13
CONNECTING THE PROJECTOR
CONNECTING TO THE VIDEO EQUIPMENT
MONITOR OUTAV IN
R–AUDIO–LS–VIDEO
Y/VIDEOCb/Pb Cr/Pr
(MONO)
R–AUDIO–LVIDEO
COMPUTER IN 2CONTROL PORT 2AUDIO 2
(STEREO)
RGBH V
RESETR/C JACKRGBH V
COMPUTER IN 1ANALOGCONTROL PORT 1AUDIO 1
(STEREO)
DIGITAL
Video Source (example)
Video Cassette Recorder Video Disc Player
Video
Cables ✽
S-VIDEO 
Cable ✽
Audio Amplifier Audio Speaker (stereo)
Audio Cable 
(Stereo) ✽
Terminals 
of the Projector
Use any of VIDEO jack Y-Pb/Cb-
Pr/Cr jacks or S-VIDEO...

14
CONNECTING THE PROJECTOR
ANALOG DIGITALCOMPUTER IN 1
COMPUTER IN 2
MONITOR OUTAV  I NCONTROL PORT 1
CONTROL PORT 2S–VIDEO
Y/VIDEO Cb/Pb Cr/Pr
R–AUDIO–L
(MONO)
AUDIO 1
AUDIO 2
(STEREO)
(STEREO)
RESETR/C JACKR–AUDIO–LVIDEO
RGBH V
RGBH V
CONNECTING TO THE COMPUTER
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA)
VGA Cable 
Monitor Output 
Desktop type Laptop type
Control Cable
for Serial Port
Audio Cable
(stereo) 
✽
Terminal
Serial port PS/2 port Audio Output
Audio Input
CONTROL...

15
MODE MENU
SELECT
NORMAL AUTO IMAGELENS SHIFT VOLUME FOCUS ZOOMON-OFF
LAMP
REPLACEWARNING
TEMP.LAMP
READY
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
Used to adjust zoom.  (P21)
Used to open or close the
MENU operation. (P18, 19)
MENU BUTTONMODE BUTTON
READY INDICATOR
POWER ON–OFF BUTTONFOCUS BUTTONS
VOLUME BUTTONS
WARNING TEMP. INDICATORLAMP INDICATORLAMP REPLACE INDICATOR
Used to select input source
either Computer or Video.
(P24, 32)
Used to operate AUTO
IMAGE function.  (P29)
Used to adjust focus....

16
VOLUME
ON-OFF
FOCUS
ZOOMVIDEO
COMPUTER
D.ZOOM
MENUMUTE
LASER
KEYSTONENO SHOWFREEZE
AUTO IMAGENORMAL
P-TIMER
LENS SHIFT
LOCK
BEFORE OPERATION
OPERATION OF THE REMOTE CONTROL
ON
ALL OFF
ALL-OFF SWITCH
Left Side
When using the Remote Control
Unit, turn this switch to “ON.”  And
turn it to “ALL OFF” when it is not
used.
This remote control emits a laser beam as the Laser Pointer from the Laser Light Window.  When the LASER button is
pressed, the laser light goes on.  And when the button is pressed more...

17
BEFORE OPERATION
To insure safe operation, please observe the following precautions :
Use (2) AA, UM3 or R06 type alkaline batteries.
Replace two batteries at the same time.
Do not use a new battery with a used battery.
Avoid contact with water or liquid.
Do not expose the Remote Control Unit to moisture, or heat.
Do not drop the remote control unit.
If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries.
Press the lid down-
ward and slide it....

18
BEFORE OPERATION
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU
Display ON-SCREEN MENU
Press MENU button to display the ON-SCREEN MENU
(MENU BAR).  The red frame is the POINTER.
Select the ITEM by pressing SELECT button.  The
dialog box of the ITEM appears.
Move the POINTER (red frame) to the ITEM ICON that
you want to select by pressing POINT RIGHT / LEFT
buttons.
Move the POINTER to the ITEM that you want to adjust
and adjust the ITEM by pressing SELECT button.
Refer to the following pages for...

19
BEFORE OPERATION
MENU BAR
SYSTEM MENU
Used to select a
computer
system.
(Refer to P24)
IMAGE MENU
Used to adjust the
computer image. 
[Fine sync / Total dots /
White Balance / Contrast
/ Brightness / Sharpness]
(Refer to P28)
PC ADJUST MENU
Used to adjust the
parameters to
match with the input
signal format.
(Refer to P26, 27)
SETTING MENU
Used to set the Display
Menu and reset Lamp
Replacement Monitor
Timer. 
(Refer to P36, 37)MODE MENU
Used to select
the Computer
input mode.
(Refer to P24)
POSITION...

20
BASIC OPERATION
TURNING ON THE PROJECTOR
Connect the projectors AC Power Cord into a wall outlet and
turn the MAIN ON / OFF SWITCH to ON.  The LAMP indicator
lights RED, and the READY indicator lights GREEN.
Press the POWER ON-OFF button on the Remote Control Unit
or on  the Top Control to ON.  The LAMP indicator dims, and the
Cooling Fans start to operate.  The Preparation Display appears
on the screen and the count-down starts.  The signal from the
source appears after 30 seconds.
2
3
TURNING OFF...