Sanyo Plc Xf60a Projector User Manual

51
Setting
PIN Code Change
Logo PIN code can be changed to your desired four-digit number.
Select “PIN code change” with the Point buttons (e, d, 7,and
8) or the Control pad and press the SELECT button. Set a new
Logo PIN code.  
Be sure to note the new Logo PIN code and keep it at hand. If
you lost the number, you could no longer change the Logo PIN
code setting. For details on PIN code setting, refer to relevant
instructions of the PJ Lock function on page 55.
Background
Three background settings are...

52
On start
When this function is “On,” the projector is automatically turned
on just by switching MAIN ON/OFF SWITCH on.
✔Note:
Be sure to turn the projector off properly (see “Turning Off the Projector” on page 28).
If the projector is turned off in the wrong steps, the On start function does not operate
properly.
Setting
Display
This function decides whether to display On-Screen Displays.
On  . . . . .shows all the On-Screen Displays.
Off  . . . . .sets On-Screen Displays disappeared except;...

53
Setting
Analog out
The ANALOG OUT terminal is for output of the analog signal
coming from the ANALOG IN terminal in the Input 1 terminals.
(See page 12.)
Select “On” to enable the signal output through the ANALOG
OUT terminal always except in the stand-by mode or “Off” to
disable the signal output.
Analog out  is not available when selecting the other Inputs except
Input 1. Select Input 1 so that Analog out will be available. (p.30,
36)   
Lens memory
Lens memory feature enables you to store the lens...

54
Setting
Security
Key lock
This function locks operation from the top control and remote
control.  It is used to prevent the projector from being operated
by an unauthorized person.  
Projector
 . . . . . . .locks operation from the top control. To
unlock, use the remote control.  
Remote control  . .locks operation from the remote control. To
unlock, use the top control.
Off  . . . . . . . . . . .unlock any operation. To release lock, select
this.
If the top control accidentally becomes locked and you...

55
Setting
The PIN code can be changed to your desired four-digit
number.
Select “PJ PIN code change” with the Point buttons (eand d)
or the Control pad, and press the SELECT button. The PIN code
input dialog box appears. Enter a current PIN code, and then a
new PIN code as follows:
Select a number with the Point buttons (e, d, 7, and 8) or the
Control pad and fix the number with the SELECT button.
Repeat it to complete entering a four-digit number. When the
four-digit number is fixed, move the pointer...

56
Setting
Factory default
This function returns all setting values to the factory default
settings except for those including: User logo, PJ PIN code, Logo
PIN code, Security setting, Lamp time, Filter time, and PJ time. 
Select Factory default and
this box appears. Select
[Yes], and the next box
appears. 
Factory default
Quit
Exits the Setting menu.
Select [Yes]
to activate it. 

57
Special 
customizes control functions: Lamp, Fan control, Filter, Auto PC adj., Test pattern, RS-
232C, and USB memory and displays Warning log. 
✔Note:
Be sure to reset the Lamp time only after replacing the lamp.
1
2
Press the MENU button to display On-Screen Menu. Spin
Menu icons with the Point buttons(e, d, 7,and 8) or
Control pad and press the SELECT button when the
SPECIAL icon comes right in front.
Move the yellow frame pointer with the Point buttons (e
and d) or Control pad to an item which...

58
Special 
Auto PC adj.
Select “On” to enable the Auto PC adjust function and “Off” to
disable it. Refer to page 30 and 40 for Auto PC adjust function.
Test pattern
Various test patterns are prepared in this projector allowing users
to test the projection. Select one from the following twenty kinds
of patterns: Cross 1 (W), Cross 2 (R), Cross 3 (G), Cross 4 (B),
Cross 5 (M), Cross 6 (C), Cross 7 (Y), Gradation 1~4, Color, and
Flat 1~8.
To cancel the Test pattern, press the CANCEL button on the top...

59
Special 
Warning log
Warning log shows the information of the past warning history of
the projector.  Up to 50 logs can be displayed. Log contents are as
follows:
Lamp-1 failure
Lamp-2 failure
Lamp-1 timeover
Lamp-2 timeover
Power failure
Inside temp. A error
Inside temp. B error
Inside temp. C error
External temp. error
Power off (Power management)
Power off (Shutter management)
PJ filter timeover
Option box filter timeover
Option box error
Warning log
Exits Warning log menu. Quit
Information...

60
If the WARNING TEMP indicator remains blinking after performing
above checks, the cooling fans or the internal circuits may be
malfunctioned. Contact the service station for check-up and repair.
Warning Temp Indicator
The WARNING TEMP indicator shows the state of the function which protects the projector. Check the state of the
WARNING TEMP indicator and the READY indicator to take proper maintenance. 
TOP CONTROL
The projector is shut down and WARNING TEMP indicator is
blinking red.
The WARNING TEMP...