Home > Sanyo > Projector > Sanyo Pdg Dxt10l Projector User Manual

Sanyo Pdg Dxt10l Projector User Manual

Here you can view all the pages of manual Sanyo Pdg Dxt10l Projector User Manual. The Sanyo manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 121

8. Specifications 
112
 
p Pin Assignments of Mini D-Sub 15 Pin Input Connector 
 
Signal Levels 
Video signal:  0.7Vp-p (Analog) 
Sync signal:  TTL level 
 
PIN NUMBER RGB SIGNAL (ANALOG) YCBCR SIGNAL 
1 Red Cr 
2 Green or Sync on Green  Y  
3 Blue  Cb  
4 Ground   
5 Ground   
6 Red Ground  Cr Ground  
7 Green Ground  Y Ground  
8 Blue Ground  Cb Ground  
9 No Connection   
10 Sync Signal Ground   
11 No Connection   
12 Bi-directional DATA (SDA)   
13 Horizontal Sync or Composite 
Sync  
 
14...

Page 122

8. Specifications 
113 
 
q Compatible Input Signal List 
The following table shows compatible signal types, their resolution and frequency refresh rates. 
Horizontal: 15kHz, 31kHz to 90 kHz 
Vertical: 50 Hz to 85 Hz 
SIGNAL RESOLUTION 
(DPI) 
FREQUENCY REFRESH 
RATE (KHZ) 
FREQUENCY REFRESH 
RATE (HZ) 
NTSC – – 15.73 60.00 
PAL  – – 15.63 50.00 
PAL60  – – 15.73 60.00 
SECAM  – – 15.63 50.00 
VESA  D 640 x 480 31.47 59.94 
MAC  D 640 x 480 35.00 66.67 
VESA  D 640 x 480 37.86 72.81 
VESA  D 640 x 480...

Page 123

8. Specifications 
114
 
SIGNAL RESOLUTION 
(DPI) 
FREQUENCY REFRESH 
RATE (KHZ) 
FREQUENCY REFRESH 
RATE (HZ) 
VESA  D 1280 x 960 60.00 60.00 
VESA  D 1280 x 1024 63.98 60.02 
VESA D 1400 x 1050 65.30 60.00 
HDTV (1080i)(1125i)  – 1920 x 1080 33.75 60.00 Interlace 
HDTV (1080i)(1125i)  – 1920 x 1080 28.13 50.00 Interlace 
HDTV (720p)(750p) – 1280 x 720 45.00 60.00 Progressive 
HDTV (720p) – 1280 x 720 37.50 50.00 Progressive 
SDTV(576p)(625p) – – 31.25 50.00  Progressive 
SDTV (480p)(525p) – – 31.47...

Page 124

8. Specifications 
115 
 
r PC Control Codes and Cable Connections 
This projector provides a function to control and monitor t he projectors operations by using the RS-232C serial port. 
1. Connect a RS-232C serial cross cable to 
SERIAL PORT IN on the projector and serial 
port on the PC. 
Launch a communication software provided 
with PC and setup the communication condi-
tion as follows: 
 Baud rate  : 38400 bps 
Parity check  : none 
Stop bit  : 1 
Flow control  : none 
Data bit  : 8   
2....

Page 125

8. Specifications 
116
Status Read Command Table 
COMMAND FUNCTION 
CR0 Status Read 
CR6 Temperature Read 
 
PC Control Connector (DIN-9P)  
 
 
Note:   
1. Pin 1, 4, 6 and 9 are not used. 
2. Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify the cable 
connection. 
3. For long cables, it is recommended to set communication speed within projector menus to 9600 bps.  

Page 126

8. Specifications 
117 
 
s Screen Trigger 
When the projector is powered ON the screen trigger output sends a low voltage trigger to the screen controller and the 
screen will go down. When the projector is powered OFF the screen trigger stops sending a low voltage trigger to the 
screen controller and the screen will go up. 
Note: 
To use this feature, you must turn on the Screen Trigger function. See Screen Trigger on page 85 for more 
information. 
 
Note: 
Screen controllers are supplied and...

Page 127

8. Specifications 
118
 
t Operation Using HTTP Browser 
Overview 
The use of HTTP server functions will allow control of the pr ojector from a web browser without the installation of special 
software. Please be sure to use “Microsoft In ternet Explorer 4.x” or a higher version for the web browser. (This device uses 
“JavaScript” and “Cookies” and the browser should be set to  accept these functions. The setting method will vary depend-
ing on the version of browser. Please refer to the help f iles and...

Page 128

8. Specifications 
119 
 
Configuring Network Settings 
The Network Settings screen is displayed as follows: 
http://  /lanconf.html 
 
Domain 
Host Name: Type in a hostname. Up to 60 alphanumeric characters can be used. 
Domain Name: Type in domain name of the network connected to the projector. Up to 60 alphanumeric characters can be used. 
Apply: Click to reflect the entries. 
 
Mail 
Alert Mail: Click “Enable” to enable Alert Mail feature. This option notifies your computer of an error message via...

Page 129

8. Specifications 
120
 
Test Mail 
Send a test mail to check if your settings are correct. Click to “Execute” to enable this feature. 
Test Mail Status Button: Click to display the test result. 
Sample of a message sent from the projector: 
Projector Name: X X X X 
Lamp 1 or 2 Hours Used: xxxx [H] 
The lamp is at the end of its usable life. Please replace the lamp. 
Note: 
If you entered an incorrect address in a test, you may not receive an Alert mail. Should this happen, check if 
the Recipients...

Page 130

8. Specifications 
121 
 
Structure of the HTTP Server 
Once the projector is connected to a network and configured correctly, the following screen is displayed through the web 
browser. 
http://  /index.html 
 
FUNCTION SETTING DESCRIPTION 
Power Panel On Off This controls the power to the projector 
Volume Panel ▲ – Increases the volume adjustment value ▼ – Decreases the volume adjustment value This controls the volume of the projector 
Mute Panel Picture On – Mutes the video Picture Off – Cancels the...
Start reading Sanyo Pdg Dxt10l Projector User Manual

Related Manuals for Sanyo Pdg Dxt10l Projector User Manual

All Sanyo manuals