Sanyo Pdg Dxt10l Projector User Manual

5. Using On-Screen Display 
82
 
Network setting 
The Network setting tab is accessed by using the Setup/Installation tab and contains the general LAN settings. 
 
The following table lists all functions with a description and the defau\
lt setting. 
ITEM DESCRIPTION 
DHCP Select either a static IP or DHCP IP setting by selecting the appropriate radio button. 
IP address Displays the IP address. 
Subnet Displays the subnet mask. 
Gateway Enable or disable the network gateway setting. Click on the radio...

5. Using On-Screen Display 
83 
 
Option 
The Option tab contains miscellaneous setup menu settings such as Power Management and Default Input Select and can 
be accessed by using the Setting Menu. 
 
The following table lists all functions with a description and the defau\
lt setting. 
ITEM DESCRIPTION 
On start Set this item on to enable the projector to power up when AC plug in.  
Range: On or Off 
Power management Select the amount of time the projector remains idle before powering down.  
Range:...

5. Using On-Screen Display 
84
ITEM DESCRIPTION 
Remote control This option switches remote control codes. 
Range: Code 1, Code 2, Code 3, Code 4, Code 5, Code 6, Code 7, Code 8 
Message This option turns on or off messages. 
Range: Off or On 
Filter warning Set this item to on to have the projector display a message when the air filter needs servicing. 
Range: Off, 100[H], 200[H], 500[H], 1000[H] 
Search mode This feature sets the Auto Adjust mode. 
Range: Normal, Fine 
 
On start 
On start enables the...

5. Using On-Screen Display 
85 
 
Select from the following: 

5. Using On-Screen Display 
86
 
Default input select 
The Default input is the image source that the projector will search for automatically on startup. 
 
Last – Uses the most recently used image source. 
Auto – Auto detects the default image source. 
Computer1/2/3 – Uses Computer1, 2 or 3 as the default image source. 
Component – Uses last component as the default image source. 
Video – Uses last video input as default image source. 
S-Video – Uses last S-video input as default image source.  

5. Using On-Screen Display 
87 
 
Remote control 
This projector has eight different remote control codes; the factory set normal mode (Code 1) and the other seven codes 
(Code 2 to Code 8). This switching function prevents remote control operation mixture (jam) when operating several projec-
tors or video equipment together. 
To change the code of Projector: 
 
To change the Remote control code of the projector used in ON SCREEN MENU is selectable from Code 1 to Code 8. 
 
Message 
This option turns on...

5. Using On-Screen Display 
88
 
Filter warning 
Set Filter warning to have the projector display a message when the air filter needs servicing.  
 
The message below shows when this function is activated. 
 
 
Search mode 
This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise and 
stability. You can automatically make adjustments in two ways: [Normal] and [Fine]. 
 
Normal: The RGB image will be automatically adjusted. Normally select this...

5. Using On-Screen Display 
89 
 
u Information Menu Descriptions and Functions 
The information menu provides only screens for the quick access of menus. The Information menu contains four distinct 
tabs. 
Usage time 
The Usage Time tab displays information about lamp usage and remaining l\
amp life. 
 
The following table lists all items with a description. 
ITEM DESCRIPTION 
Lamp1 Life remaining Displays the Lamp1 life remaining as a percentage. 
Lamp2 Life remaining Displays the Lamp2 life remaining...

5. Using On-Screen Display 
90
 
Input 
The Input tab displays various source and frequency values at a glance. 
 
The following table lists all items with a description. 
ITEM DESCRIPTION 
Input name Displays the Input Terminal that is presently being used 
(see Default input select on page 86). 
Signal Displays the Source name of the signal presently being used 
(see Option on page 83). 
H-sync. freq. Displays Horizontal frequency in KHz. 
V-sync. freq. Displays Vertical frequency in Hz. 
Video type...

5. Using On-Screen Display 
91 
 
Network 
The Network tab displays LAN settings as previously defined (see Network setting on page 82).