Sanyo Pdg Dxl100 Projector Quickstart Guide

11
English
SERVICEPORTCOMPUTER IN 1
COMPONENT IN 1( VARIABLE )AUDIO OUTMONITOR OUTS-VIDEO INVIDEO INAUDIO IN
COMPUTER IN 2
COMPONENT IN 2
E62405SPR
Connecting the Projector
	Due to the differ-ence in applications for each country, some regions may have differ-ent accessories.
	When AUDIO OUTPUT is plugged-in, the projector’s build-in speaker is not available.-
Note
		To ensure the projector works well with your computer, 
please make sure the timing of the display mode is 
compatible with your...

12
SERVICEPORTCOMPUTER IN 1
COMPONENT IN 1( VARIABLE )AUDIO OUTMONITOR OUTS-VIDEO INVIDEO INAUDIO IN
COMPUTER IN 2
COMPONENT IN 2
E62405SPR
	Due to the differ-ence in applications for each country, some regions may have dif-ferent accessories.
	When AUDIO OUTPUT is plugged-in, the projector’s build-in speaker is not available.
Note
		To ensure the projector works well with your computer, 
please make sure the timing of the display mode is 
compatible with your projector....

13
English
Adjusting the Projected Image
Adjusting the Height of Projector Image
The projector is equipped with adjustable feet to raise and lower 
the image to fill the screen.
 To raise/lower the image:
1.   Use  to fine-tune the display angle.
You can raise the projector front up to 3 degrees by rotating the adjustable feet.
Note
1
Front Adjustable feet
Rear Adjustable feet
1
Maximun Length:7mm
Maximun Length:2mm 

14
40 
(101.6cm) 100
(254.0cm) 150
(381.0cm) 200
(508.0cm) 250
(635.0cm) 307
(779.8cm)
1.624
12.464 10.150 8.120 6.090 4.060
(0.495m)
(3.799m) (3.094m) (2.475m) (1.856m) (1.237m)
Lens Center
A
B
H
ALens Center
H : A = 6.78
B ÷ H x 100% = 115%(Offset)
B
Diagonal
Focus Ring
Adjusting the Projector Focus
To focus the image, rotate the focus ring until the image is clear. 
The projector will focus at distances from 1.62 to 12.46 feet (0.5 
to 3.8 meters) with mechanical travel.
Adjusting Projection Image...

15
English
Powering On the Projector
1. Ensure that the power cable and signal cable are securely 
connected. The POWER LED will turn orange.
2.   Remove the lens cap. 
3.   Turn on the lamp by pressing “ON/STAND-BY” on the 
control panel.  The POWER LED will now flash green.
 The startup screen will display in approximately 5 seconds. 
When disappear startup screen, the POWER LED will turn 
green.
4.   Turn on your source (computer, notebook, video player, 
etc.) The projector will detect your source...

16
Powering Off the Projector
1.    Press the “ON/STAND-BY” to turn off the projector lamp, 
you will see a message as below on the on-screen display.
 
2.   Press the “ON/STAND-BY” again to confirm. 
3.   The cooling fan continues to operate for about 60 seconds for 
cooling cycle and the POWER LED will flash green. When 
the light starts flashing orange, the projector has entered 
standby mode.
   If you wish to turn the projector back on, you must wait 
until the projector has completed the cooling...

17
English
The Projector has a multilingual On Screen Display that allows 
you to make image adjustments and change a variety of set-
tings. The projector will automatically detect the source. 
How to operate
1. To open the OSD, press “MENU” on the Remote Control.
2.  When OSD is displayed, use      keys to select any item in the 
main menu. While making a selection on a particular page, press  
  key to enter sub menu.
3.  Use      keys to select the desired item in the sub menu and 
adjust the settings...

18
Replacing the lamp
The projector will detect the lamp life itself.  It will show you a 
warning message
When you see this message, change the lamp as soon as pos-
sible. Make sure the projector has been cooled down for at 
least 60 minutes before changing the lamp. 
Warning: To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp!
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause...

19
English
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering a 
projection lamp, give the following information to the dealer.
■ Model No. of your projector  : PDG-DXL100
■ Replacement Lamp Type No.  : POA-LMP138 
      (Service Parts No. 610 346 4633)
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully\
 and 
properly.
Improper handling may result in accidents, injury, or create a fire hazard.
■  Lamp life may differ...

20
Specifications
Projection SystemSingle Chip DLP® Technology by Texas Instruments
Number of PixelsXGA: 1024 pixels(H) X 768 lines(V), up to UXGA (1600 X 1200) with \
scaling technology
Lamp225W (170W on ECO mode)
Projection LensF#2.6  f=6.97mm with manual focus
Projection Screen Size (Diag.)40 to 307 inches (1.02 to 7.80 meters) Diagonal
Projection Distance1.62 to 12.46 feet (0.5 to 3.8 meters)
Video Compatibility-  NTSC-M/NTSC-4.43/PAL-B, D, G, H, I/PAL-M/PAL-N/SECAM-  Component: SDTV(480i/576i),...