Sanyo Pdg Dxl100 Projector Quickstart Guide

							11
English
SERVICEPORTCOMPUTER IN 1
COMPONENT IN 1( VARIABLE )AUDIO OUTMONITOR OUTS-VIDEO INVIDEO INAUDIO IN
COMPUTER IN 2
COMPONENT IN 2
E62405SPR
Connecting the Projector
	Due to the differ-ence in applications for each country, some regions may have differ-ent accessories.
	When AUDIO OUTPUT is plugged-in, the projector’s build-in speaker is not available.-
Note
		To ensure the projector works well with your computer, 
please make sure the timing of the display mode is 
compatible with your projector.
1.........................................................................\
...................Power cable (supplied)2.........................................................................\
.......................................RS232 cable3.........................................................................\
.............................HDMI-DVI cable4.........................................................................\
.....................VGA cable (supplied)5.........................................................................\
.............Audio in cable jack to jack 6.........................................................................\
...........Audio out cable jack to jack 7.........................................................................\
..................................Network cable 8.........................................................................\
............................Monitor out cable 
VGA, DVI
	Make sure that the power plug is fully inserted into both the projector AC inlet and the wall outlet.
	The AC outlet must be near this equipment and must be easily ac-cessible.
Note
1
243
6
5
Connect to Computer/Notebook
87
Audio Output
Monitor Output 
						

							12
SERVICEPORTCOMPUTER IN 1
COMPONENT IN 1( VARIABLE )AUDIO OUTMONITOR OUTS-VIDEO INVIDEO INAUDIO IN
COMPUTER IN 2
COMPONENT IN 2
E62405SPR
	Due to the differ-ence in applications for each country, some regions may have dif-ferent accessories.
	When AUDIO OUTPUT is plugged-in, the projector’s build-in speaker is not available.
Note
		To ensure the projector works well with your computer, 
please make sure the timing of the display mode is 
compatible with your projector.
1.........................................................................\
...................Power cable (supplied)2.........................................................................\
......................................HDMI cable3.........................................................................\
...................Composite video cable4.........................................................................\
.............Audio in cable jack to jack 5.........................................................................\
...........Audio out cable jack to jack 6.........................................................................\
...................................S-Video cable
Video Output
S-Video Output
DVD player, Set-top BoxHDTV receiver	Make sure that the power plug is fully inserted into both the projector AC inlet and the wall outlet.
	The AC outlet must be near this equipment and must be easily accessible.
	Other than the analog RGB signal, COMPUTER IN 1/2-COMPONENT IN 1/2 Connectors can be used to project the incoming Component and RGB Scart signals.
(See Page 20 for the Optional Parts.)
Note
1
243
65
Connect to Video
Audio Output 
						

							13
English
Adjusting the Projected Image
Adjusting the Height of Projector Image
The projector is equipped with adjustable feet to raise and lower 
the image to fill the screen.
 To raise/lower the image:
1.   Use  to fine-tune the display angle.
You can raise the projector front up to 3 degrees by rotating the adjustable feet.
Note
1
Front Adjustable feet
Rear Adjustable feet
1
Maximun Length:7mm
Maximun Length:2mm 
						

							14
40 
(101.6cm) 100
(254.0cm) 150
(381.0cm) 200
(508.0cm) 250
(635.0cm) 307
(779.8cm)
1.624
12.464 10.150 8.120 6.090 4.060
(0.495m)
(3.799m) (3.094m) (2.475m) (1.856m) (1.237m)
Lens Center
A
B
H
ALens Center
H : A = 6.78
B ÷ H x 100% = 115%(Offset)
B
Diagonal
Focus Ring
Adjusting the Projector Focus
To focus the image, rotate the focus ring until the image is clear. 
The projector will focus at distances from 1.62 to 12.46 feet (0.5 
to 3.8 meters) with mechanical travel.
Adjusting Projection Image Size
This graph is for user’s reference only.
Screen (Diagonal)40” (101.6cm)100” (254.0cm)150” (381.0cm)200” (508.0cm)250” (635.0cm)307” (779.8cm)Screen Size (WxH) cm32.0” x 24.0”(81.3 x 61.0cm)80.0” x 60.0” (203.2 x 152.4cm)120.0” x 90.0”(304.8 x 228.6cm)160.0” x 120.0”(406.4 x 304.8cm)200.0” x 150.0”(508.0 x 381.0cm)245.6” x 184.2”(623.8 x 467.9cm)Distance1.624’ (0.495m)4.060’ (1.237m)6.090’ (1.856m)8.120’ (2.475m)10.150’ (3.094m)12.464’ (3.799m) 
						

							15
English
Powering On the Projector
1. Ensure that the power cable and signal cable are securely 
connected. The POWER LED will turn orange.
2.   Remove the lens cap. 
3.   Turn on the lamp by pressing “ON/STAND-BY” on the 
control panel.  The POWER LED will now flash green.
 The startup screen will display in approximately 5 seconds. 
When disappear startup screen, the POWER LED will turn 
green.
4.   Turn on your source (computer, notebook, video player, 
etc.) The projector will detect your source automatically.
		If you connect multiple sources at the same time, use the 
“INPUT” on the remote control or use “COMPUTER 1”, 
“COMPUTER 2”, “S-VIDEO”, “VIDEO”, “HDMI” on the 
remote control to switch inputs.
Powering On/Off the Projector
Turn on the projector first and then the signal sources.
Note
Lens CapPower
12 
						

							16
Powering Off the Projector
1.    Press the “ON/STAND-BY” to turn off the projector lamp, 
you will see a message as below on the on-screen display.
 
2.   Press the “ON/STAND-BY” again to confirm. 
3.   The cooling fan continues to operate for about 60 seconds for 
cooling cycle and the POWER LED will flash green. When 
the light starts flashing orange, the projector has entered 
standby mode.
   If you wish to turn the projector back on, you must wait 
until the projector has completed the cooling cycle and has 
entered standby mode. Once in standby mode, simply press 
“ON/STAND-BY” to restart the projector.
4.   Disconnect the power cable from the electrical outlet and the 
projector.
5.   Do not turn on the projector immediately following a power 
off procedure. 
						

							17
English
The Projector has a multilingual On Screen Display that allows 
you to make image adjustments and change a variety of set-
tings. The projector will automatically detect the source. 
How to operate
1. To open the OSD, press “MENU” on the Remote Control.
2.  When OSD is displayed, use      keys to select any item in the 
main menu. While making a selection on a particular page, press  
  key to enter sub menu.
3.  Use      keys to select the desired item in the sub menu and 
adjust the settings by      key. 
4.  
If the setting has  icon, you could press “ENTER” to enter an-
other sub menu. Press “MENU” to close the sub menu after adjust-
ment.
5.   After adjusting the settings, press “MENU” go back to the main 
menu.
6.    To exit, press “MENU” again. The OSD will be closed and the pro-
jector will automatically save the new settings.
On Screen Display
If no button operation is made for 30 seconds, the OSD will be closed automatically.
Note
Main Menu
Sub MenuSetting 
						

							18
Replacing the lamp
The projector will detect the lamp life itself.  It will show you a 
warning message
When you see this message, change the lamp as soon as pos-
sible. Make sure the projector has been cooled down for at 
least 60 minutes before changing the lamp. 
Warning: To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp!
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause 
injury if it is dropped.
Warning: For contin-ued safety replace with a lamp of the same type.
 Lamp Replacing Procedure: 
 1.   Switch off the power to the projector by pressing the “ON/STAND-BY”.
  2. Allow the projector to cool down at least 60 minutes.
  3. Disconnect the power cable.
  4. Use a screwdriver to remove the 2 screws from the cover. 
	5. Push up and remove the cover. 
	6.   Remove the 2 screws from the lamp module  and pull up  the lamp bar. 
  7.  Pull out the lamp module by force. 
  8.    Install the new lamp module by reversing the previous steps. 
  9.   After replacing the lamp, turn on the power, and select the menu ->[Setting] ->[Lamp Counter Reset] to reset the lamp usage hours.
1
2
4
3 
						

							19
English
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering a 
projection lamp, give the following information to the dealer.
■ Model No. of your projector  : PDG-DXL100
■ Replacement Lamp Type No.  : POA-LMP138 
      (Service Parts No. 610 346 4633)
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully\
 and 
properly.
Improper handling may result in accidents, injury, or create a fire hazard.
■  Lamp life may differ from lamp to lamp and according to the environment \
of 
use. There is no guarantee of the same life for each lamp. Some lamps ma\
y fail or 
terminate their life in a shorter period of time than other similar lamp\
s.
■  If the projector indicates that the lamp should be replaced, i.e., if th\
e lamp life 
warning message appears, replace the lamp with a new one IMMEDIATELY aft\
er 
the projector has cooled down. (Follow carefully the instructions in th\
e Lamp Re-
placement section of this manual.) Continuous use of the lamp with show\
ing the 
lamp life warning message may increase the risk of lamp explosion.
■  A Lamp may explode as a result of vibration, shock or degradation as a r\
esult of 
hours of use as its lifetime draws to an end. Risk of explosion may diff\
er according 
to the environment or conditions in which the projector and lamp are bei\
ng used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS 
SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC ou\
tlet immedi-
ately. Contact an authorized service station for a checkup of the unit a\
nd replace-
ment of the lamp. Additionally, check carefully to ensure that there are\
 no broken 
shards or pieces of glass around the projector or coming out from the co\
oling air 
circulation holes. Any broken shards found should be cleaned up carefull\
y. No one 
should check the inside of the projector except those who are authorized\
 trained 
technicians and who are familiar with projector service. Inappropriate a\
ttempts to 
service the unit by anyone, especially those who are not appropriately t\
rained to do 
so, may result in an accident or injury caused by pieces of broken glass\
. 
						

							20
Specifications
Projection SystemSingle Chip DLP® Technology by Texas Instruments
Number of PixelsXGA: 1024 pixels(H) X 768 lines(V), up to UXGA (1600 X 1200) with \
scaling technology
Lamp225W (170W on ECO mode)
Projection LensF#2.6  f=6.97mm with manual focus
Projection Screen Size (Diag.)40 to 307 inches (1.02 to 7.80 meters) Diagonal
Projection Distance1.62 to 12.46 feet (0.5 to 3.8 meters)
Video Compatibility-  NTSC-M/NTSC-4.43/PAL-B, D, G, H, I/PAL-M/PAL-N/SECAM-  Component: SDTV(480i/576i), EDTV(480p, 576p), HDTV(720p, 1080i/p)
H. Frequency31.35kHz~79.98kHz horizontal scan
V. Frequency50Hz~75Hz vertical refresh
Power SupplyUniversal AC input 100-240V ; Input Frequency 50-60Hz
Power ConsumptionNormal mode:320W
Standby mode