Sanyo Pdg Dwl100 Projector User Manual

50
English
Appendices
Computer Compatibility (Analog)
(1) Signals from D-sub 15
ModesResolutionV.Frequency(Hz) H.Frequency(kHz) 
VGA640 x 4806031.50
640 x 4807237.90
640 x 4807537.50
720 x 4007031.50
SVGA800 x 6005635.20
800 x 6006037.90
800 x 6007248.10
800 x 6007546.90
832 x 6247549.725
XGA1024 x 7686048.40
1024 x 7687056.50
1024 x 7687560.00
SXGA*1280 x 10246063.98
*1280 x 10247579.98
WXGA1280 x 7206045.00
1280 x 8006049.702
*1440 x 9006055.935
QuadVGA*1280 x 9606059.70
SXGA+*1400 x 10506063.98...

English
51
English
Appendices
Computer Compatibility (Digital-
HDMI)
(1) PC digital signals with HDMI-DVI cable 
ModesResolutionV.Frequency(Hz) H.Frequency(kHz) 
VGA640 x 4806031.50
640 x 4807237.90
640 x 4807537.50
720 x 4007031.50
SVGA800 x 6005635.20
800 x 6006037.90
800 x 6007248.10
800 x 6007546.90
832 x 6247549.725
XGA1024 x 7686048.40
1024 x 7687056.50
1024 x 7687560.00
SXGA*1280 x 10246063.98
*1280 x 10247579.98
WXGA1280 x 7206045.00
1280 x 8006049.702
*1440 x 9006055.935
QuadVGA*1280 x...

52
English
Appendices
(2) AV digital signals with HDMI cable 
ModesResolutionV.Frequency(Hz) 
480i1440 x 48060
480p (NTSC)640 x 48060
480p (NTSC)720 x 48060
576i (PAL)1440 x 57650
576p (PAL)720 x 57650
720p (NTSC)1280 x 72060
720p (PAL)1280 x 72050
1080i (NTSC)1920 x 108060
1080i (PAL)1920 x 108050
1080p (NTSC)1920 x 108060
1080p (PAL)1920 x 108050 

English
53
English
Appendices
Configurations of Terminals
1RXD
2***
3***
4GND
5***
6TXD
7***
8***
Terminal : Analog RGB (Mini D-sub 15 pin)
1Red (R/Cr) Input/R Output95V / ***
2Green (G/Y) Input/G Output10Ground (Ver. sync.)
3Blue (B/Cb) Input/B Output11ICP download
4***12DDC data / ***
5Ground (Horiz.sync.)13Horiz.  sync.  Input  /  Output  (Composite  H/V sync. Input)6Ground (Red)
7Ground (Green)14Vert. sync. Input / Output
8Ground (Blue)15DDC clock / ***
876
4 3
2 1
5
Terminal : Mini DIN 8-pin
5
4321...

54
English
Appendices
Regulation & Safety Notices
This appendix lists the general notices of your Projector. 
FCC notice 
This device has been tested and found to comply with the limits 
for a Class B digital device pursuant to Part 15 of the FCC rules. 
These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This 
device generates, uses and can radiate radio frequency energy 
and, if not installed and used in accordance with the instruc-...

English
55
English
Appendices
FOR EU USERS
The symbol mark and recycling systems described below apply to EU countr\
ies and 
do not apply to countries in other areas of the world.
Your product is designed and manufactured with high quality materials and compo-
nents which can be recycled and/or reused.
The symbol mark means that electrical and electronic equipment, batteries and accu-
mulators, at their end-of-life, should be disposed of separately from your household 
waste.
Note:
If a chemical symbol...

56
English
Appendices
Operation
1. Connect a RS-232C serial cross cable to SERVICE PORT on the 
projector and serial port on the PC.
2. Launch a communication software provided with PC and setup the 
communication condition as follows:
3. Type the command for controlling the projector and then enter the 
“Enter” key.
 Example
 When you want to change the input to Computer 2, Type ‘C’ ‘0’ ‘6’ 
‘Enter’.
Serial Control Interface
  This projector provides a function to control and monitor the 
projector’s...

English
57
English
Appendices
CommandFunctionCommandFunction
C00POWER ONC24YPbPr 2
C01POWER OFF (Immediate POWER OFF)
C25---
C26Scart
C04HDMIC27IMAGE(Toggle)
C05Computer 1C30D.zoom +
C06Computer 2C31D.zoom -
C09Volume +C33Video
C0AVolume -C34S-Video
C0BSOUND MUTE ONC35YPbPr 1
C0CSOUND MUTE OFFC3APOINTER RIGHT
C0DVIDEO MUTE ONC3BPOINTER LEFT
C0EVIDEO MUTE OFFC3CPOINITER UP
C0FAspect 4:3C3DPOINITER DOWN
C10Aspect 16:10C3FENTER
C11Image mode PresentationC43FREEZE ON
C12Image mode MovieC44FREEZE OFF
C13Image...

58
English
Appendices
Status Read Command
Format
The command is sent from PC to the projector with the format below;
‘CR’ [Command] ‘CR’ 
Command: one character (refer to the command table below.
■  The projector decodes the command and returns the ‘Character 
string’ with the format below;
CommandFunctionProjectorReturnProjector status
CR0Status Read
00Power ON
20Cooling Down
10 Power Failure
28Cooling Down due to Abnormal Temperature in process
21Cooling Down in process after Off due to lamp failure...

English
59
English
Appendices
Use of Telnet
  You can control the projector by using the telnet application 
installed on your computer. Normally, the telnet application 
is available on your computer.
The telnet 10000 port is used to control the projector.
Further instructions about the telnet ap-plication, please see the on-line guide on your computer.
Note
Control
(For example, in case of using the telnet application of Windows XP 
Professional.)
1.  Select Run... submenu from Start menu on the...