Sanyo Pdg Dwl100 Projector User Manual

40
English
User Controls
Logout Page
When you use this page, the projector system will go back Login mode. 

English
41
English
Appendices
Problem: No image appears on screen
  Ensure all the cables and power connections are correctly and 
securely connected as described in the “Installation” section.
 Ensure the pins of connectors are not crooked or broken.
  Check if the projection lamp has been securely installed. Please 
refer to the “Replacing the lamp” section.
  Make sure you have removed the lens cap and the projector is 
switched on.
  Ensure that the “AV-MUTE” feature is not turned on.
Problem:...

42
English
Appendices
 4.   Verify the resolution setting is less than or equal to 1600 x 1200 
resolution.
  5.   Select the “Change” under the “Monitor” tab .
  6.   Click on “Show all devices”. Next, select “Standard monitor 
types” under the SP box; choose the resolution mode you need 
under the “Models” box. 
 If you are using a Notebook:
  1.   First, follow the steps above to adjust resolution of the com-
puter.
  2. Press the toggle output settings. example: [Fn]+[F4]
  
   If you experience...

English
43
English
Appendices
   Check and reconfigure the display mode of your graphic card to 
make it compatible with the product. 
Problem: Image is out of focus
 Adjust the Focus Ring on the projector lens. 
   Make sure the projection screen is between the required distance 
1.65 to 12.13 feet (0.5 to 3.7 meters) from the projector (refer to 
page 19).
Problem: The image is stretched when displaying 16:9 DVD
 
The projector automatically detects 16:9 DVD and adjusts the aspect 
ratio by...

44
English
Appendices
Steady light => No light => *=> When LED light on after 5 sec., go to standby mode. 
Note
MessagePOWER-LEDTEMP- LEDLAMP-LED
(Red)(Green)(Orange)(Red)(Red)
Standby (Input power cable)
Normal (Power on)
Powering up (Warming up)Flashing
Power off (Cooling-I: It can’t accept any key at this status)Flashing
Power off (Cooling-II: It can accept power key to turn on the projector)Flashing
Error (Lamp failed) *
Error (Fan lock)Flashing
Error (Over temp.)
Problem: LED lighting message 

English
45
English
Appendices
Problem: Message Reminders
  Over temperature - the projector has exceeded its recommended 
operating temperature and must be allowed to cool down before it 
may be used.
 
  Replacing the lamp - the lamp is about to reach its maximum life-
time. Prepare to replace  it soon. 
 
 Fan failed - the system fan is not working.
 
 Setting network 
 
 Loading network 
  

46
English
Appendices
Replacing the lamp
The projector will detect the lamp life itself.  It will show you a 
warning message 
 
When you see this message, change the lamp as soon as pos-
sible. Make sure the projector has been cooled down for at 
least 45 minutes before changing the lamp. 
Warning: To avoid burns, allow the projector to cool for at least 45 minutes before you replace the lamp!
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb...

English
47
English
Appendices
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering a 
projection lamp, give the following information to the dealer.
■ Model No. of your projector  : PDG-DWL100
■ Replacement Lamp Type No.  : POA-LMP138 
   (Service Parts No. CHSP8EM01GC01 or 610 346 4633)
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully\
 and 
properly.
Improper handling may result in accidents, injury, or create a fire...

48
English
Appendices
Cleaning the Air Filters
Air filters prevent dust from accumulating on the optical 
elements inside the projector. Should the air filters become 
clogged with dust particles, it will reduce cooling fans’ effec-
tiveness and may result in internal heat build up and adverse-
ly affect the life of the projector. Clean the air filters following 
the steps below.
 Air Filters Cleaning Procedure: 
 1.   Turn off the projector, and disconnect the AC power cord from the AC outlet.
  2....

English
49
English
Appendices
Specifications
Projection SystemSingle Chip DLP® Technology by Texas Instruments
Number of PixelsWXGA: 1280 pixels(H) X 800 lines(V), up to UXGA (1600 X 1200) with scaling technology
Lamp225W (170W on ECO mode)
Projection LensF#2.6  f=7.198mm with manual focus
Projection Screen Size (Diag.)46 to 338 inches (1.16 to 8.59 meters) Diagonal
Projection Distance1.65 to 12.13 feet (0.5 to 3.7 meters)
Video Compatibility-  NTSC-M/NTSC-4.43/PAL-B, D, G, H, I/PAL-M/PAL-N/SECAM-...