Sanyo Pdg Dsu30 Projector User Manual

40
English
Appendices
Specifications
Projection SystemSingle Chip DLP® Technology by Texas Instruments
Number of PixelsSVGA: 800 pixels(H) × 600 lines(V), up to UXGA (1600 X 1200) with scaling technology
Lamp180W (160W on ECO mode)
Projection LensF#2.41~2.55  f=21.8~24 mm with 1.1× manual zoom lens
Projection Screen Size (Diag.)27.46 to 302.80 inches (0.7 to 7.7 meters) Diagonal
Projection Distance3.94 to 39.36 feet (1.2 to 12.0 meters)
Video Compatibility-  NTSC-M/NTSC-4.43/PAL-B, D, G, H,...

English
41
English
Appendices
Computer Compatibility
ModesResolutionV.Frequency(Hz) H.Frequency(kHz) 
VGA640 x 3508537.90
640 x 4008537.90
640 x 4806031.50
640 x 4807237.90
640 x 4807537.50
640 x 4808543.30
720 x 4007031.50
720 x 4008537.90
SVGA800 x 6005635.20
800 x 6006037.90
800 x 6007248.10
800 x 6007546.90
800 x 6008553.70
XGA*1024 x 7686048.40
*1024 x 7687056.50
*1024 x 7687560.00
*1024 x 7688568.70
WXGA*1280 x 7686047.40
*1280 x 7687560.30
*1280 x 7206045.00
*1280 x 8006049.30
SXGA*1152 x...

42
English
Appendices
Configurations of Terminals
1TXD
2RXD
3GND
Terminal : Analog RGB (Mini D-sub 15 pin)
1Red (R/Cr) Input/R Output95V / ***
2Green (G/Y) Input/G Output10Ground (Ver. sync.)
3Blue (B/Cb) Input/B Output11ICP download
4***12DDC data / ***
5Ground (Horiz.sync.)13Horiz.  sync.  Input  /  Output  (Composite  H/V sync. Input)6Ground (Red)
7Ground (Green)14Vert. sync. Input / Output
8Ground (Blue)15DDC clock / ***
31
2
Terminal : Mini DIN 3-pin
5 4321
10 98 76
15 141312 11 

English
43
English
Appendices
Declaration of Conformity
Model number: PDG-DSU30
Trade name: SANYO
Responsible party: SANYO North America Corporation
Address: 21605 Plummer Street Chatsworth, California 91311
Telephone: (818) 998-7322
Regulation & Safety Notices
This appendix lists the general notices of your Projector. 
FCC notice 
This device has been tested and found to comply with the limits 
for a Class B digital device pursuant to Part 15 of the FCC rules. 
These limits are designed to provide...

44
English
Appendices
Operation conditions 
This device complies with Part 15 of the FCC Rules. Operation 
is subject to the following two conditions:
1.  This device may not cause harmful interference and
2.  This device must accept any interference received, in-
cluding interference that may cause undesired operation. 
Notice: Canadian users 
This Class B digital apparatus complies with Canadian 
ICES-003. 
Remarque à l’intention des utilisateurs cana-
diens 
Cet appareil numerique de la classe B est...

English
45
English
Appendices
FOR EU USERS
The symbol mark and recycling systems described below apply to EU countr\
ies and 
do not apply to countries in other areas of the world.
Your product is designed and manufactured with high quality materials and compo-
nents which can be recycled and/or reused.
The symbol mark means that electrical and electronic equipment, batteries and accu-
mulators, at their end-of-life, should be disposed of separately from your household 
waste.
Note:
If a chemical symbol...

46
English
Appendices
Operation
1. Connect the specified RS-232C control cable to SERVICE PORT on 
the projector and serial port on the PC.
2. Launch a communication software provided with PC and setup the 
communication condition as follows:
3. Type the command for controlling the projector and then enter the 
“Enter” key.
 Example
 When you want to change the input to Computer, Type ‘C’ ‘0’ ‘5’ 
‘Enter’.
Serial Control Interface
  This projector provides a function to control and monitor the...

English
47
English
Appendices
CommandFunctionCommandFunction
C00POWER ONC30D.zoom +
C01POWER OFF (Immediate POWER OFF)
C31D.zoom -
C3APOINTER RIGHT
C05ComputerC3BPOINTER LEFT
C09Volume +C3CPOINTER UP
C0AVolume -C3DPOINTER DOWN
C0BSOUND MUTE ONC33VIDEO
C0CSOUND MUTE OFFC34S-VIDEO
C0DAV MUTE ONC43FREEZE ON
C0EAV MUTE OFFC44FREEZE OFF
C0FAspect 4:3C89AUTO ADJ.
C10Aspect 16:9-IC8EKEYSTONE +
C11Image mode PresentationC8FKEYSTONE -
C12Image mode Movie
C13Image mode sRGB
C14Image mode Bright
C15Image mode User...

48
English
Appendices
Status Read Command
Format
The command is sent from PC to the projector with the format below;
‘CR’ [Command] ‘CR’ 
Command: one character (refer to the command table below.
■  The projector decodes the command and returns the ‘Character 
string’ with the format below;
CommandFunctionProjectorReturnProjector status
CR0Status Read00Power ON
80Standby mode
CR1Input Mode Read 
CR3Lamp Time Read 
CR4Setting Read 
The tables on pages 46~48 show the typical command lists for con-trolling...

English
49
English
Appendices
Dimensions
3.24/82.30mm
Lens Center
2.48/63.00mm
Screw Holes for Ceiling Mount
Screw: M3
Depth: 0.30~0.39/7.5~10.0mm
11.27/286.31mm
7.56/192.00mm
3.96/100.60mm
1.67/42.39mm
1.75/44.39mm
3.47/88.15mm
3.06/77.75mm
2.17/55.00mm4.33/110.00mm
4.67/118.65mm 6.60/167.66mm
Lens Center
4.94/125.53mm
2.28/57.79mm3.03/77.00mm
0.41/10.54mm
3.7° Max.