Sanyo Pdg Dht8000l Projector User Manual

1

KEySTONE button
Reduce  the  upper  width  with Point e button. Re d u c e   t h e   l owe r   w i d t h with Point d button.Reduce  the  left  part  with Point 7 button.Reduce  the  right  part  with Point 8 button.
• The white arrows indicate that there is no correction.
•  A red arrow indicates the direction of correction.
•  An arrow disappears at the maximum correction.
•  If you press the KEYSTONE button on the remote 
control again while the Keystone dialog box is being displayed, the...



Remote Control
INPUT buttons
Input 
Press the INPUT 1, INPUT 2, INPUT 3 or INPUT 4 button 
on the remote control. The input source appears on the 
screen as you press each button. Select the connected 
input source.
Remote Control Operation
Side Control
INPUT button
Press the INPUT button on the side control. It switches to 
INPUT 1, INPUT 2, INPUT 3 and INPUT 4 as you press the 
INPUT button. 
Before using the INPUT button on the side control, you 
must select a correct input source by...



Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the INPUT Menu icon.
Use the Point ed buttons to move the red arrow pointer 
to the desired input and then press the SELECT button.
Then you can switch to the desired input. 
1
2
Use the Point ed buttons to select the desired source 
and then press the SELECT button.
3
RGB (PC analog)
Menu Operation
Input Selection
Input 1
INPUT MENU
Move the pointer (red arrow) to the desired...

4

When the video input signal is connected to the S-VIDEO 
jack, select S-video.
When the video input signal is connected to the Y-Pb/Cb-
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
When the video input signal is connected to the VIDEO 
jack, select Video.
When connecting to video equipment, select the type of 
Video source in the Source Select Menu. 
Video
y, Pb/Cb, Pr/Cr
S-video
Menu Operation
Input Menu icon
Move the pointer (red arrow) to Input 2 and press the SELECT button.
Input 
Move the...

5

Computer System Selection
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, SXGA+, 
WXGA, UXGA, or WUXGA (refer to “Compatible Computer Specifications” on pages 82-83). If a comput\
er is 
selected as a signal source, this projector automatically detects the si\
gnal format and tunes to project a proper 
image without any additional settings. (Some computers need to be set manually.) 
One of the following messages may appear when:
When the projector...

6

Auto PC Adjustment
Auto  PC  Adjustment  function  is  provided  to  automatically  adjust  Fine  sync, Total  dots,  Horizontal  and  Vertical 
positions to conform to your computer. 
Press  the  MENU  button  to  display  the  On-Screen  Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the PC Adjust Menu icon.
1
2
Use the Point ed buttons to move the red frame pointer 
to  the  AUTO  PC  adj.  icon  and  then  press  the  SELECT 
button twice.PC AD
jUST MENU
Auto PC adj .
To...

7

Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector. 
Manual PC Adjustment enables you to precisely adjust several parameters to match those special signal 
formats. The projector has 10 independent memory areas to store those manually adjusted parameters. It 
allows you to recall the setting for a specific computer. 
✔Note:  
The PC Adjust Menu cannot be operated when the digital signal input on the DVI terminal is...

8

Exit the PC Adjust Menu.
To store the adjusted data, select Store and then press the 
SELECT button. Move the red arrow pointer to one of the Mode 
1 to 10 in which you want to store, and then press the SELECT 
button.
To reset the adjusted data, select Reset and press the SELECT 
button. A confirmation box appears and then select [Yes]. All 
adjustments will return to their previous figures.To store the adjusted data . To clear the adjusted data .
To clear the adjusted data, select Mode free...

9

Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the Image Select Menu icon.
1
2
Use the Point ed buttons to move the red frame pointer 
to the desired image level and then press the SELECT 
button.
IMAGE SELECT MENU
Normal picture level preset on the projector.
Standard
Picture level with improved halftone for graphics.
Real
User preset picture adjustment in the Image Adjust Menu. 
(p.48)
IMAGE 1–10
Image Level Selection
Menu...

40

✔Note:
• True, Full, and Digital zoom +/– cannot be selected 
when no signal is detected in the PC System 
Menu. (p.35)
•  The projector cannot display the resolution higher 
than 1920 x 1200. If your computer’s screen 
resolution is higher than that, lower the resolution 
before connecting the projector.
•  The image data other than 1920 x 1080 dots are 
modified to fit the screen size in initial mode.
•  The panning function may not operate properly if 
the stored Mode in the PC Adjust Menu is...