Sanyo Pdg Dht100l Projector User Manual

							
1

KEySTONE button
Reduce  the  upper  width  with Point e button. Re d u c e   t h e   l owe r   w i d t h with Point d button.Reduce  the  left  part  with Point 7 button.Reduce  the  right  part  with Point 8 button.
• The white arrows indicate that there is no correction.
•  A red arrow indicates the direction of correction.
•  An arrow disappears at the maximum correction.
•  If you press the KEYSTONE button on the remote 
control again while the Keystone dialog box is being displayed, the keystone adjustment will be canceled.
•  The adjustable range can be limited depending on the 
input signal.
•  “Keystone” disappears after 10 seconds.
Press the P-TIMER button on the remote control. The 
Timer display “00 : 00” appears on the screen and starts 
to count time (00 : 00–59 : 59). 
To stop the P-TIMER, press the P-TIMER button. 
To cancel the P-TIMER, press the P-TIMER button again.
P-TIMER button
P-Timer display
Remote Control
P-TIMER 
button
SHUTTER
button
✔Note:
•See  the  previous  page  for  the  description  of 
other buttons.
IMAGE  ADj . 
button
Press the KEYSTONE button on the remote control. The 
“Keystone” appears on the screen.
Use the Point ed7 8 buttons to correct keystone 
distortion. The keystone adjustment can be stored
 (pp.41, 45).
Basic Operation
KEy STONE 
button
IMAGE SEL .
 
button
Press the IMAGE ADJ. button on the remote control to 
adjust a image level of the screen.
For more detail, see pp.46-48.
IMAGE AD j . button
IMAGE SEL .  button
Press the IMAGE SEL. button on the remote control to 
select a desired image level of the screen.
For more detail, see pp.39, 43.
SHUTTER button
See page 28 for details.
FILTER button
Press and hold the FILTER button for more than five 
seconds to replace the filter mechanically. See page 56 
for details.
FILTER
button
✔Note:•The filter cannot be rewound. 
• When  the  filter  is  replaced,  the  total  accumulated  time  of the filter use is automatically set to 0. 
						

							


Remote Control
INPUT buttons
Input 
Press the INPUT 1, INPUT 2, INPUT 3 or INPUT 4 button 
on the remote control. The input source appears on the 
screen as you press each button. Select the connected 
input source.
Remote Control Operation
Side Control
INPUT button
Press the INPUT button on the side control. It switches to 
INPUT 1, INPUT 2, INPUT 3 and INPUT 4 as you press the 
INPUT button. 
Before using the INPUT button on the side control, you 
must select a correct input source by On-Screen Menu 
and the latest input source will be displayed.
Side Control Operation
Side Control button operation
Input Selection
INPUT button
INPUT 1
INPUT 
INPUT 
INPUT 4
✔Note:
 • Empty slots cannot be selected.
  • When a slot is empty, the input is displayed in grayout.
Remote Control button operation
INPUT 1 button
Input 1
RGB (PC analog)
RGB (Scart)
RGB (PC digital)
RGB (AV HDCP)
INPUT  button
Input 
RGB
y,Pb/Cb,Pr/Cr
Video
HDMI
S-video 
						

							


Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the INPUT Menu icon.
Use the Point ed buttons to move the red arrow pointer 
to the desired input and then press the SELECT button.
Then you can switch to the desired input. 
1
2
Use the Point ed buttons to select the desired source 
and then press the SELECT button.
3
RGB (PC analog)
Menu Operation
Input Selection
Input 1
INPUT MENU
Move the pointer (red arrow) to the desired source and press the SELECT button.
Source Select Menu
Input Menu icon
Move the pointer (red arrow) to Input 1 and press the SELECT button.
Computer Input Source Selection
When Selecting the INPUT 1 with DVI/D-sub 15 terminals
When your computer is connected to the INPUT 1 (ANALOG) 
terminal, select RGB (PC analog).
When your computer is connected to INPUT 1 (DIGITAL) 
terminal, select RGB (PC digital).
RGB (PC digital)
When Selecting the INPUT  with 5-BNC/Video/S-video terminals
INPUT MENU
Move the pointer (red arrow) to Input 2 and press the SELECT button.
Input 
Move the pointer (red arrow) to RGB and press the SELECT button.
Source Select Menu
When your computer is connected to the INPUT 2 (5 BNC 
INPUT JACKS) terminal, select RGB.
RGB 
✔Note: • When a slot is empty, the input is displayed in grayout.
Press the select button again. The Source Select Menu 
appears. 
4
Input Menu icon 
						

							
4

When the video input signal is connected to the S-VIDEO 
jack, select S-video.
When the video input signal is connected to the Y-Pb/Cb-
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
When the video input signal is connected to the VIDEO 
jack, select Video.
When connecting to video equipment, select the type of 
Video source in the Source Select Menu. 
Video
y, Pb/Cb, Pr/Cr
S-video
Menu Operation
Input Menu icon
Move the pointer (red arrow) to Input 2 and press the SELECT button.
Input 
Move the pointer (red arrow) to Y, Pb/Cb, Pr/Cr , Video, or S-video and press the SELECT button.
Source Select Menu
Video Input Source Selection
Input Selection
When connecting to video equipment, select the type of 
Video source in the Source Select Menu. 
Input 1
INPUT MENU
Move the pointer (red arrow) to RGB (Scart), RGB (AV HDCP), or HDMI and press the SELECT button.
Source Select Menu
Input Menu icon
Move the pointer (red arrow) to Input 1 and press the SELECT button.
RGB (AV HDCP)
RGB (Scart)
When scart video equipment is connected to the INPUT 1 
(ANALOG) terminal, select RGB (Scart).
If the HDCP-compatible signal source is connected to the 
INPUT 1 (DIGITAL) terminal, select RGB (AV HDCP).
INPUT MENU
When Selecting the INPUT 1 with DVI/D-sub 15 terminals
When Selecting the INPUT  with 5-BNC/Video/S-video terminals
✔Note:
•   HDCP  (High-bandwidth  Digit al  Content  Protection)  is  a 
system for protecting digital entertainment content which is 
delivered by DVI (Digital Visual Interface) from being copied. 
The  specification  of  HDCP  is  decided  and  controlled  by 
Digital Content Protection, LLC. Should the specification be 
changed,  this  projector  may  not  display  the  digital  content 
protected by HDCP.
•  When a slot is empty, the input is displayed in grayout.
HDMI
When the video signal is connected to the HDMI terminal, 
select HDMI. 
						

							
5

Computer System Selection
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, SXGA+, 
WXGA, UXGA, or WUXGA (refer to “Compatible Computer Specifications” on pages 80-81). If a comput\
er is 
selected as a signal source, this projector automatically detects the si\
gnal format and tunes to project a proper 
image without any additional settings. (Some computers need to be set manually.) 
One of the following messages may appear when:
The projector cannot recognize the connected 
signal conforming to the provided PC Systems. 
The “Auto” is displayed on the PC System Menu 
icon and the Auto PC Adjustment function works to 
display proper images. If the image is not projected 
properly, a manual adjustment is required. (pp.37–
38.)
There is no signal input from the computer. Check 
the connection between your computer and the 
projector. (See “Troubleshooting” on page 71.)
Auto
-----
PC System Menu iconSelected system is displayed.
PC SySTEM MENU
Selecting Computer System Manually
Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the PC System Menu icon.
Use the Point ed buttons to move the red arrow pointer 
to the desired system, and then press SELECT button. 
1
2
PC S ySTEM MENU
PC system can also be selected manually.
Automatic Multi-Scan System
The preset system is manually adjusted in the PC 
Adjust Menu. The adjusted data can be stored in 
the Mode 1–10. (pp.37-38)
Mode 1
PC systems provided in this projector is chosen. 
The projector chooses a proper system provided in 
the projector and displays it.
SVGA 1
✽ Mode 1 and SVGA 1 are examples.
PC System Menu icon Selected system is displayed
Systems in this dialog box can be selected.
Custom Mode (1–10) set in PC Adjust Menu. (pp.37-38)
Computer Input 
						

							
6

Auto PC Adjustment
Auto  PC  Adjustment  function  is  provided  to  automatically  adjust  Fine  sync, Total  dots,  Horizontal  and  Vertical 
positions to conform to your computer. 
Press  the  MENU  button  to  display  the  On-Screen  Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the PC Adjust Menu icon.
1
2
Use the Point ed buttons to move the red frame pointer 
to  the  AUTO  PC  adj.  icon  and  then  press  the  SELECT 
button twice.PC AD
jUST MENU
Auto PC adj .
To store the adjusted parameters .
The  adjusted  parameters  from  the  Auto  PC  Adjustment  can be  stored  in  the  projector.  Once  the  parameters  are  stored, the  setting  can  be  done  just  by  selecting  Mode  in  PC  SYSTEM Menu (p.35). See Manual PC Adjustment on pages 37-38.
✔Note:
•Fine sync, Total dots, Horizontal and Vertical position of 
certain computers cannot be fully adjusted with the Auto 
PC Adjustment function. When the image is not provided 
properly with this operation, manual adjustments are 
required. (pp.37-38.)
•Auto PC Adjustment cannot be operated in Digital Signal 
Input on the DVI terminal and “480p,” “575p,” “480i,” “575i,” 
“720p,” “1035i,” “1080p,” or “1080i” is selected on the PC 
SYSTEM Menu.
•Depending on the condition of signals and the type and 
length of cables, the signals may not be properly viewed.
PC Adjust Menu icon
Move the red frame pointer to the Auto PC adj. and press the SELECT button twice.
“Please wait...” appears while the Auto PC adjustment is in process.
The Auto PC adjustment function can be operated 
directly by pressing the AUTO PC button on the remote 
control or the AUTO PC ADJ. button on the side control.
Direct OperationRemote Control
Menu Operation
Computer Input
AUTO PC button
Side Control
AUTO PC AD j . 
button 
						

							
7

Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector. 
Manual PC Adjustment enables you to precisely adjust several parameters to match those special signal 
formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It 
allows you to recall the setting for a specific computer. 
✔Note:  
The PC Adjust Menu cannot be operated when the digital signal input on the DVI terminal is selected on PC 
System Menu. 
Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the PC Adjust Menu icon.
1
2Use the Point ed buttons to move the red frame pointer 
to the desired item and then press the SELECT button 
to display the adjustment dialog box. Use the Point 7 8 
buttons to adjust the setting value.
Use  the  Point 7  8 buttons  to  adjust  the  value,  eliminating  a 
flicker from the image displayed (from 0 to 31).
Fine sync
Use the Point 7 8 buttons to adjust the number of total dots in 
one horizontal period to match your PC image.
Total dots
Use  the  Point 7  8  buttons  to  adjust  the  horizontal  picture 
position.
Position H
Use the Point 7 8 buttons to adjust the vertical picture position.
Position V
Press  the  SELECT  button  to  show  H-sync  freq.  and V-sync  freq. 
of the connected computer.
Current mode
Use  the  Point 7 8  buttons  to  adjust  the  clamp  level. When  the 
image has dark bars, try this adjustment.
Clamp
Press the SELECT button at Current mode icon to show the information of the connected computer.
Current mode
Use the Point 7 8 buttons to adjust the horizontal area displayed 
by this projector.
Display area H
Use  the  Point 7  8  buttons  to  adjust  the  vertical  area  displayed 
by this projector.
Display area V
Move the red frame pointer to the desired item and press the SELECT button.
Press the Point 7 8 buttons to adjust the value.
Press the SELECT button at this icon to adjust “Clamp,” “Display area H,” or “Display area V.”
Selected Mode
Status (Stored/Free) of the Selected Mode.
Press the SELECT button at this icon to display the previous items.
PC ADjUST MENU
PC Adjust Menu icon
Computer Input 
						

							


Exit the PC Adjust Menu.
To store the adjusted data, select Store and then press the 
SELECT button. Move the red arrow pointer to one of the Mode 
1 to 10 in which you want to store, and then press the SELECT 
button.
To reset the adjusted data, select Reset and press the SELECT 
button. A confirmation box appears and then select [Yes]. All 
adjustments will return to their previous figures.To store the adjusted data . To clear the adjusted data .
To clear the adjusted data, select Mode free and then press the 
SELECT button. Move the red arrow pointer to the Mode that 
you want to clear and then press the SELECT button.
Reset
Mode free
Store
Quit
This Mode has stored parameters.
Vacant
Values of “Total dots,” “Position H,” “Position V,” “Display area H,” and “Display area V.”
Close this dialog box.
Close this dialog box.
Confirmation box appears and then select [Yes].
Confirmation box appears and then select [Yes].
Computer Input 
						

							
9

Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the Image Select Menu icon.
1
2
Use the Point ed buttons to move the red frame pointer 
to the desired image level and then press the SELECT 
button.
IMAGE SELECT MENU
Normal picture level preset on the projector.
Standard
Picture level with improved halftone for graphics.
Real
User preset picture adjustment in the Image Adjust Menu. 
(p.48)
IMAGE 1–10
Image Level Selection
Menu Operation
Image Select Menu icon
Move the red frame pointer to the desired level and press the SELECT button.
Computer Input
Press the IMAGE SEL. button on the remote control to 
select the desired image level.
Direct Operation
Remote Control
IMAGE SEL . 
button
Standard
Real
Image1
Image 10
•••
Dynamic
For viewing contrasty images in a bright room.
Dynamic 
						

							
40

✔Note:
• True, Full, and Digital zoom +/– cannot be selected 
when no signal is detected in the PC System 
Menu. (p.35)
•  The projector cannot display the resolution higher 
than 1920 x 1080. If your computer’s screen 
resolution is higher than 1600 x 1200, lower the 
resolution before connecting the projector.
•  The image data other than 1920 x 1080 dots are 
modified to fit the screen size in initial mode.
•  The panning function may not operate properly if 
the stored Mode in the PC Adjust Menu is used. 
(p.38)
Screen Size Adjustment
Select the desired screen size that conforms to the input signal source.
Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the Screen Menu icon.
1
Use the Point ed buttons to move the red frame pointer 
to the desired function and then press the SELECT 
button.
2
Normal
SCREEN MENU
Provide the image at the normal computer aspect ratio of 4:3.
True
Provide the image in its original size. When the original image 
size is larger than the screen size (1920 x 1080), the projector 
enters to the panning mode automatically. Use the Point ed7 
8 buttons to pan the image. When adjusted, the arrows will 
turn red. When reached to the correction limits, the arrows will 
disappear.
Full
Provide the full screen image.
Screen Menu icon
Move the red frame pointer to the desired function and press the SELECT button.
  Scale H/V  ..............  Adjust the Horizontal/Vertical screen scale.
  H&V  ......................  When set to “On,” the aspect ratio is 
fixed. The “Scale V” appears dimmed and 
becomes unavailable. Adjust “Scale H,” 
then the screen scale is automatically 
modified based on the aspect ratio. 
  Position H/V  ..........  Adjust the Horizontal/Vertical screen 
position.
  Common  ..............  Save the adjusted scale to all the inputs. 
Press the SELECT button at Common to 
display a confirmation box. To save the 
scale, press the SELECT button at “Yes.” 
When Custom is selected, the saved scale 
is used.
  Reset  ....................  Reset the all adjusted values. Press 
the SELECT button at Reset to display 
a confirmation box. To reset, press the 
SELECT button at “Yes.”
Custom
✔Note:
•  When no signal is detected, “Normal” is set 
automatically and the Aspect dialog box disappears.
•  The adjustable range for Scale H/V and Position H/V 
is limited depending on the input signal.
Press the SELECT button at Common or Reset, to display a confirmation box.
Computer Input
Adjust the screen scale and position manually with this 
function.
Press the SELECT button at Custom and the “Custom” is 
displayed on the screen for a few seconds. To display the 
Aspect dialog box, press the SELECT button at Custom again 
and then the Aspect dialog box appears.