Sanyo Pdg Dht100l Projector User Manual
Have a look at the manual Sanyo Pdg Dht100l Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
1 Appendix ON-SCREEN DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz) 1080p 1920x108033.75030.000 1920x108028.12525.000 1920x108027.00024.000 1920x108067.50060.000 1920x108056.25050.000 1080psf/301920x108033.75060.000 1080psf/251920x108028.12550.000 1080psf/241920x108027.00048.000 When an input signal is digital from the DVI terminal, refer to the chart below. ✔Note: •Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed. •Specifications are subject to change without notice. ON-SCREEN DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz) D-VGA640x48031.470 59.940 D-480p720x48031.470 59.880 D-575p720x57531.250 50.000 D-SVGA800x60037.879 60.320 D-XGA1024x76843.363 60.000 D-WXGA 11366x76848.360 60.000 D-WXGA 21360x76847.700 60.000 D-WXGA 31376x76848.360 60.000 D-WXGA 41360x76856.160 72.000 D-WXGA 51366x76846.500 50.000 D-WXGA 61280x76847.776 59.870 D-WXGA 71280x76860.289 74.893 D-WXGA 81280x76868.633 84.837 D-WXGA 91280x80049.600 60.050 D-WXGA 101280x80041.200 50.000 D-WXGA 111280x80049.702 59.810 D-SXGA 11280x102463.980 60.020 D-SXGA 21280x102460.276 58.069 D-SXGA+ 11400x105063.970 60.190 D-SXGA+ 21400x105065.350 60.120 D-SXGA+ 31400x105065.120 59.900 ON-SCREEN DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz) D-WUXGA 21920x120074.03859.950 D-WSXGA+ 11680x105065.290 59.954 D-WXGA+ 11440x90055.935 59.887 D-720p1280x72045.000 60.000 D-720p1280x72037.500 50.000 D-1035i1920x1035 (Interlace)33.750 60.000 D-1080i 1920x1080 (Interlace)33.750 60.000 1920x1080 (Interlace)28.125 50.000 D-1080psf/301920x108033.750 60.000 D-1080psf/251920x108028.125 50.000 D-1080psf/241920x108027.000 48.000 D-1080p 1920x108033.75030.000 1920x108028.12525.000 1920x108027.00024.000 1920x108067.50060.000 1920x108056.25050.000 SystemmodeRESOLUTION H-Freq .(kHz)V-Freq .(Hz) D-VGA640x480−59.94/60 D-WXGA61280x76847.776 59.870 D-WXGA71280x76860.289 74.893 D-WXGA81280x76868.633 84.837 D-WXGA91280x80049.572 59.870 D-WXGA101280x80041.200 50.000 D-480i720x480−59.94/60 D-575i720x575−50.00 D-480p720x480−59.94/60 SystemmodeRESOLUTION H-Freq .(kHz)V-Freq .(Hz) D-575p720x575−50.00 D-720p1280x720−59.94/60 D-720p1280x720−50.00 D-1080i1920x1080−59.94/60 D-1080i1920x1080−50.00 D-1080p1920x1080−59.94/60 D-1080p1920x1080−50.00 D-1080p1920x1080−24.00 When the input signal is digital from the HDMI terminal, refer to the chart below. ✔Note: • You might be able to project images even when signals other than above are inputted, however the functions of the projector could be limited.
Appendix
On-BoardOptional Interface Board
Input1Input2DsubDsub-DVIComponent-S-videoComponentHDCP-DVISDIHDwirelessAnalog PCScartDigitalAnalog PC
ComponentVideo/S-VideoAnalog PCAnalog PCScartDigitalAnalog PC
ComponentVideo/S-videoAnalog PC
ComponentAnalog PCScartDigitalDigitalHD DataWireless
On-BoardInput1
Analog PCo o o o o o o o o o o o o o o o o o
Scarto o o - - - - o - - - - - - - o o o
Digitalo o o o o o o - - o o o o o o - - - -
On-BoardInput2
Analog PCo o o o o o o o o o o o o o o o o
Componento o o o o o o o o o o o o o o o o
Video/S-Videoo - o - - - o - - - - - - - o o o
List of Picture in Picture
o : Picture in Picture combinations are enabled
- : Picture in Picture combinations are disabled
✔Note:
• You cannot select Input 3 and Input 4 (e.g. SDI and HD wireless) simultaneously as images of Main picture and Sub
picture.
•
When the input signal(s) is/are incompatible, X mark will be displayed on the Main/Sub picture.
• Depending on the frequency or signal type of PC/AV input,
the display resolution may be lowered or images may not be
displayed on the Main/Sub picture.
• Inputting PC analog signals: Between 100-160 MHz
• Inputting AV analog signals: 1080p
• Inputting PC analog signals: More than 160MHz
• Inputting PC digital signals: More than 100MHz
• Inputting AV digital signals: 1080p
Technical Specifications
Mechanical Information
Projector Type Multi-media Projector
Dimensions (W x H x D) 15.75” x 9.55” x 20.61” (400.0 mm x 242.5 mm x 523.5 mm)
Net Weight 43.65lbs (19.8 kg)
Feet Adjustment 0˚ to 5˚
DLP Chip
Projection System 0.95” Single DLP chip, High brightness color wheel x 2
Number of Pixels 2,073,600 pixels (1,920 x 1,080 dots)
Signal Compatibility
Color System PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N
High Definition TV Signal 480i, 480p, 575i, 575p, 720p, 1035i, 1080p, and 1080i
Scanning Frequency H-sync. 15 kHz–120 kHz, V-sync. 48 Hz–120 Hz
Optical Information
Projection Lamp 330 W UHP lamp x 2
Interface
Input 1 DVI-D Terminal (Digital), Mini D-Sub 15-pin Terminal (Analog), HDMI
Input 2 BNC Type x 5 (VIDEO/Y/G, B/Pb/Cb, R/Pr/Cr, H/HV and V), S-Video
Input 3 Vacant
Input 4 Network Board
Monitor Output Mini D-sub 15 pin
Other Jacks Serial port in (D-sub 9), Serial port out (D-sub 9), USB port, and Wired Remote Jack
Power
Voltage and Power Consumption AC 100–120 V (9.2A Max. Ampere), 50/60 Hz (The U.S.A and Canada)
AC 200-240 V (4.4A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)
Operating Environment
Operating Temperature 41˚F–104˚F (5˚C–40˚C)
Storage Temperature 14˚F–140˚F (-10˚C–60˚C)
Remote Control
Battery AA or LR6 Type x 2
Operating Range 16.4’ (5 m/±30˚)
Dimensions 1.79” (W) x 1.03” (H) x 6.24” (D) (45.5 mm x 26.2 mm x 158.5 mm)
Net Weight 4.1 oz (117 g) (including batteries)
Accessories
Owner’s Manual (CD-ROM)
Quick Reference Guide
AC Power Cord
Remote Control and Batteries
VGA Cable
PIN Code Label
Cable covers (support cover & cover)
Fixing bracket for power cord
Rich color reproduction color wheel x 2
Ferrite core (for LAN cable)
Strap x 2
Cable tie x 3
Real Color Manager Pro (CD-ROM)
Appendix
4
Optional Parts
Model No.
Wired Remote Cable(30m)
: POA-CA-RC30
Optional Interface Board (DVI)
: POA-MD18DVI
Optional Interface Board (5-BNC)
: POA-MD16VD1
Optional Interface Board (D-sub 15)
: POA-MD04VGA
Optional Interface Board (Dual-SDI)
: POA-MD17SDID
Optional Interface Board (DVI / D-sub 15)
: POA-MD23ADI
Optional Interface Board (5-BNC / VIDEO)
: POA-MD25VD3
Optional Interface Board (HD DATA Wireless Receiver)
: POA-MD26HDWL
HD DATA Wireless Transmitter Box
: POA-HDTM01
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No.
to the sales dealer.
Appendix
l The specifications are subject to change without notice.
l Each projector has its own characteristics.
When projecting with several projectors on the same screen or side by side, you may recognize different white balance
and color uniformity on each projector.
✔Note:
• Between the two features of the provided Real Color Manager Pro (CD-ROM); "Color Correction" and "Gamma Correction", "Color Correction" is not available with this projector.
5 Configurations of Terminals ANALOG (Mini D-sub 15 pin) 512341096781514131112 Red Input Ground (Horiz.sync.) Green Input No Connect Blue Input Ground (Red) Ground (Green) Ground (Blue) 1 5 4 6 7 +5V Power Horiz. sync. Ground (Vert. sync.) DDC Data Ground Vert. sync. DDC Clock 9 1 10 1 11 14 15 CONTROL PORT CONNECTOR (D-sub 9 pin) ----- R X D T X D ----- SG ----- RTS CTS Serial 1 4 5 6 7 DIGITAL DVI-D (DVI 4 PIN) 1917 21018 31119 41220 51321 61422 71523 81624 T.M.D.S. Data2– No Connect T.M.D.S. Data2+ No Connect T.M.D.S. Data2 Shield DDC Clock DDC Data No Connect 1 5 4 6 7 T.M.D.S. Data1– No Connect T.M.D.S. Data1+ No Connect T.M.D.S. Data1 Shield +5V Power Ground (for +5V) Hot Plug Detect 9 1 10 1 11 14 15 16 T.M.D.S. Data0– No Connect T.M.D.S. Data0+ No Connect T.M.D.S. Data0 Shield T.M.D.S. Clock Shield T.M.D.S. Clock+ T.M.D.S. Clock– 17 1 1 0 19 4 Vcc - Data + Data Ground 1 4 USB CONNECTOR (Series B) 2 3 4 1 Appendix -----9 Red Output Ground (Horiz.sync.) Green Output No Connect Blue Output Ground (Red) Ground (Green) Ground (Blue) 1 5 4 6 7 Horiz. sync. Output Ground (Vert.sync.) No Connect No Connect Vert. sync. Output No Connect 9 1 10 1 11 14 15 No Connect Input Output 13579111315171918161412108642 TMDS Data 2+ Input Ground (TMDS Data 1) Ground (TMDS Data 2) TMDS Data 1+ Input TMDS Data 2- Input TMDS Data 1- Input TMDS Data 0+ Input Ground (TMDS Data 0) 1 5 2 4 3 6 7 8 Ground (TMDS Clock) SCL TMDS Clock- Input ----- ----- SDA Ground (DDC/CEC) 11 15 12 14 13 16 17 19 Pin Type A TMDS Data 0- Input TMDS Clock+ Input 9 10 Plug insert detection19 18+5V Power HDMI
6 Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. Factory default set No: 1 2 3 4* Factory default set No: 4 3 2 1* * S h o u l d t h e fo u r- d i g i t n u m b e r b e changed, the factory set number will be invalid. Put the label below (supplied) on in a prominent place of the projector’s body while it is locked with a PIN code. While the projector is locked with the PIN code... PIN Code Lock No. Logo PIN Code Lock No. PIN Code Number Memo Appendix
7 Dimensions Unit: inch (mm) Appendix 0.28(7.0) 9.21(234.0)9.55(242.5) 4.45(113.0) 20.47(520.0)20.61(523.5) 15.75(400.0) 8.31(211.0) 5.0º 5.0º 19.96(507.1) 96.0º 6.02(153.0)5.63(143.0) 6.81(173.0)6.81(173.0) 5.08(129.0)4.65(118.0) 2.64(67.0) 4.25(108.0) 12.48(317.0) 5.79(147.0)4.92(125.0) 6.50(165.0)6.50(165.0) 14.29(363.0) Screw Holes for Ceiling MountScrew: M8Depth: 0.393 (10.0)
Serial Control Interface
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial
port.
Connect a RS-232C serial cross cable to SERIAL
PORT IN on the projector and serial port on the PC.
(See p.11)
Launch a communication software provided with PC
and setup the communication condition as follows:
1
2
3
Baud rate : 9600 / 19200 bps
Parity check : none
Stop bit : 1
Flow control : none
Data bit : 8
Type the command for controlling the projector and
then enter the "Enter" key.
Example
When you want to change the input to INPUT 2,
Type 'C' '0' '6' 'Enter'.
✔Note:
• The default of the baud rate is set to 19200 bps. If an
error occurs in the communication, change the serial
port and the communication speed (baud rate).
•Enter with ASCII 64-byte capital characters and one-
byte characters.
The command is sent from PC to the projector with
the format below;
'C' [Command] 'CR'
Command: two characters (refer to the
command table below.
-The projector decodes the command and returns the
'ACK' with the format below;
'ACK' 'CR'
-When the projector cannot decode the command, it
returns with format below.
‘?’ ‘CR’
Format
Operation
Appendix
Functional Execution Command
CommandFunction
C00Turn the projector ON
C01Turn the projector OFF
(immediately OFF)
C05Select Input 1
C06Select Input 2
C07Select Input 3
C08Select Input 4
C0DVideo mute ON
C0EVideo mute OFF
C0FAspect 4:3
C10Aspect 16:9
C1CMenu ON
C1DMenu OFF
C3APointer RIGHT
CommandFunction
C3BPointer LEFT
C3CPointer UP
C3DPointer DOWN
C3FEnter
C46Zoom DOWN
C47Zoom UP
C4AFocus DOWN
C4BFocus UP
C5DLens shift UP
C5ELens shift DOWN
C5FLens shift LEFT
C60Lens shift RIGHT
C89Auto PC Adj.
C8EKeystone UP
C8FKeystone DOWN
C90Keystone RIGHT
C91Keystone LEFT
9
Status Read Command
Appendix
The command is sent from PC to the projector with
the format below;
'CR' [Command] 'CR'
Command: one character (refer to the command
table below.
The projector decodes the command and returns the
'Character string' with the format below;
Format
CommandFunctionProjector
ReturnProjector status
CR0Status Read
00Power On
80Stand-by mode
40Countdown
20Cooling down
10Power Malfunction
28Cooling down at the temperature anomaly
02Unable to receive the RC232C command.
24Cooling down at Power Management mode
04Power Management mode after Cooling down
21Cooling down after the projector is turned off when the lamps
are out.
81Stand-by mode after Cooling down when the lamps are out.
88Stand-by mode after Cooling down at the temperature
anomaly.
2CCooling down when the projector is turned off by the shutter
management function.
8CStand-by mode after Cooling down by the shutter
management function.
CR6Temperature ReadS1 S2 S3
S1 = Temperature at Sensor 1 (˚C)
S2 = Temperature at Sensor 2 (˚C)
S3 = Temperature at Sensor 3 (˚C)
(ex.) S1 = 12.3˚C, S2 = 23.4˚C, S3 = 34.5˚C
--> The projector displays “12.3 23.4 34.5”
( For each sensor, two digit and the tenth place numbers are
displayed with a space between each temperature.)
?Communication failure
The tables on pages 88 and 89 show the typical command lists for controlling the projector. Please consult your
local dealer for further information of other commands.