Sanyo Pdg Dht100l Projector User Manual

1

Appendix
ON-SCREEN DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
1080p
1920x108033.75030.000
1920x108028.12525.000
1920x108027.00024.000
1920x108067.50060.000
1920x108056.25050.000
1080psf/301920x108033.75060.000
1080psf/251920x108028.12550.000
1080psf/241920x108027.00048.000
When an input signal is digital from the DVI terminal, refer to the chart below.
✔Note:
•Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.
•Specifications are...



Appendix
On-BoardOptional Interface Board
Input1Input2DsubDsub-DVIComponent-S-videoComponentHDCP-DVISDIHDwirelessAnalog PCScartDigitalAnalog PC
ComponentVideo/S-VideoAnalog PCAnalog PCScartDigitalAnalog PC
ComponentVideo/S-videoAnalog PC
ComponentAnalog PCScartDigitalDigitalHD DataWireless
On-BoardInput1
Analog PCo    o    o    o    o    o    o    o    o    o    o    o    o    o    o    o    o    o    
Scarto    o    o    -        -        -        -        o    -        -        -        -...



Technical Specifications
Mechanical Information 
 Projector Type  Multi-media Projector 
  Dimensions (W x H x D)  15.75” x 9.55” x 20.61” (400.0 mm x 242.5 mm x 523.5 mm)
 
  Net Weight  43.65lbs (19.8 kg)
 
  Feet Adjustment  0˚ to 5˚           
              
DLP Chip 
 Projection System  0.95” Single DLP chip, High brightness color wheel x 2  
  Number of Pixels  2,073,600 pixels (1,920 x 1,080 dots)           
             
Signal Compatibility 
 Color System PAL, SECAM, NTSC, NTSC4.43,...

4

Optional Parts
     Model No.
Wired Remote Cable(30m)    
: POA-CA-RC30 
Optional Interface Board (DVI)    
: POA-MD18DVI
Optional Interface Board (5-BNC)    
: POA-MD16VD1
Optional Interface Board (D-sub 15) 
: POA-MD04VGA
Optional Interface Board (Dual-SDI) 
: POA-MD17SDID
Optional Interface Board (DVI / D-sub 15) 
: POA-MD23ADI
Optional Interface Board (5-BNC / VIDEO) 
: POA-MD25VD3
Optional Interface Board (HD DATA Wireless Receiver)  
: POA-MD26HDWL
HD DATA Wireless Transmitter Box  
:...

5

Configurations of Terminals
ANALOG (Mini D-sub 15 pin)
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
No Connect
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5

4

6
7

+5V Power
Horiz. sync.
Ground (Vert. sync.)
DDC Data
Ground
Vert. sync.
DDC Clock
9
1
10
1
11
14
15
CONTROL PORT CONNECTOR (D-sub 9 pin)
-----
R X D
T X D
-----
SG
-----
RTS
CTS
Serial
1


4
5
6
7

DIGITAL DVI-D (DVI 4 PIN)
1917
21018
31119
41220
51321...

6

Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or 
lost the number and unable to operate the projector, contact the service station. 
Factory default set No:  1 2 3 4*
Factory default set No:  4 3 2 1*
*  S h o u l d   t h e   fo u r- d i g i t   n u m b e r   b e 
changed,  the  factory  set  number  will 
be invalid.
Put the label below (supplied) on in a prominent place of 
the projector’s body while it is locked with a PIN code.
While...

7

Dimensions
Unit: inch (mm)
Appendix
0.28(7.0)
9.21(234.0)9.55(242.5)
4.45(113.0)
20.47(520.0)20.61(523.5)
15.75(400.0)
8.31(211.0)
5.0º
5.0º
19.96(507.1)
96.0º
6.02(153.0)5.63(143.0)
6.81(173.0)6.81(173.0)
5.08(129.0)4.65(118.0)
2.64(67.0)
4.25(108.0)
12.48(317.0)
5.79(147.0)4.92(125.0)
6.50(165.0)6.50(165.0)
14.29(363.0)
Screw Holes for Ceiling MountScrew: M8Depth: 0.393 (10.0) 



Serial Control Interface
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial 
port.
Connect a RS-232C serial cross cable to SERIAL 
PORT IN on the projector and serial port on the PC.
 (See p.11)
Launch a communication software provided with PC 
and setup the communication condition as follows:
1
2
3
Baud rate : 9600 / 19200 bps
Parity check  : none
Stop bit   : 1
Flow control  : none
Data bit   : 8
Type the command for...

9

Status Read Command
Appendix
The command is sent from PC to the projector with 
the format below;
     'CR' [Command] 'CR'
        Command: one character (refer to the command 
table below.
The projector decodes the command and returns the 
'Character string' with the format below;
Format
CommandFunctionProjector 
ReturnProjector status
CR0Status Read
00Power On
80Stand-by mode
40Countdown
20Cooling down
10Power Malfunction
28Cooling down at the temperature anomaly...

KT5AL-ASANyO Electric Co  ., Ltd .