Samsung Television UNES7150 User Manual

							5. 
To set up wireless security, enter the 
Security Key or a  WPS PIN using the 
keyboard on the Enter security key 
screen.
 
NTo enter letters, highlight and 
select each letter. To enter 
numbers, highlight and select 
each number or press the number 
buttons on your remote.
 
NTo shift to capital letters (or from 
capital letters to lower case),  
						

							select the Caps or Shift button.
 
N To display symbols and 
punctuation, select 1
. To 
redisplay letters, select 1
 again.
 
N You should be able to find the 
Pass Phrase on one of the set up 
screens you used to set up your 
router or modem.
 6.  When done, select Next if you 
entered a Security Key or WPS PIN  
if you entered a PIN. The network  
						

							connection screen appears and the 
verification process starts.
7.  
Select  Stop. The verification process 
stops. Select IP Settings on the 
network connection screen. The IP 
Settings screen appears.
8.  
Select  IP Mode, and then set the IP 
Mode to  Enter manually .
9.  
Go to the IP Address entry field, and 
then select the IP Address using the 
remote. 
						

							10. 
Enter the first portion of the IP 
Address (for example, 105) into the 
first entry field using your remote. 
When done, go to the next field.
11.  
Enter the next portion of the IP 
Address. When done, go to the next 
field.
12.  
Repeat the entry process for each 
field in the IP Address.
 
NIf you make a mistake when 
entering a number, re-enter the  
						

							number to correct it.
13.  
When done, go to the  Subnet Mask 
fields.
14.  
Repeat the same entry process for 
Subnet Mask, Gateway , and DNS 
Server .
15.  
When done, select OK. The network 
connection screen appears and the 
verification process starts. When the 
connection has been verified, the 
"You are connected to the Internet. If  
						

							you have any problems using online 
services, please contact your Internet 
Service Provider." message appears. 
Select OK.
WPS(PBC)  Network Setup
If your router has a WPS(PBC) 
button, you can configure your TV's 
wireless network connection using the 
WPS(PBC) button quickly and easily.
To set up your TV's wireless network 
connection using WPS(PBC) , follow  
						

							these steps:1.  
Go  to  Network Settings screen. 
(Network  
→  Network Settings)
2.  
Select  Start. The network function 
searches for available wireless 
networks. When done, it displays a 
list of the available networks.
3.  
Select  WPS(PBC) .
4.  
Press the WPS(PBC) button on your 
router within 2 minutes. Your TV 
automatically acquires all the network  
						

							setting values it needs and connects 
to your network.
5.  
The network connection screen 
appears, and network setup is done.
Plug & Access Network Setup The Plug & Access function lets you 
easily connect your Samsung TV to 
your Samsung wireless router by using 
a USB memory stick to transfer the 
setup information from the router to 
the TV. If your non-Samsung wireless  
						

							router does not support Plug & Access, 
you must connect using one of the 
other methods.
 
NYou can check for equipment that 
supports Plug & Access on www.
samsung. com.
To set up your TV's wireless network 
connection using Plug & Access, follow 
these steps: 1.  
Turn on the Samsung wireless router 
and your TV. 
						

							2. 
Insert a USB memory stick into the 
USB port in your Samsung wireless 
router. Check the router’s LED’s to 
make sure it is on (Blinking 
→ on).
3.  
Take the USB memory stick out of 
the router, and then insert it into 
a USB port on your Samsung TV. 
The memory stick downloads the 
connection information.
4.  
Wait until the connection is 
automatically established.