Samsung Television SyncMaster 400PXn User Manual

							Remove the 4 screws on the back of the 
product. 
Insert the screw B into the plastic hanger. 
 
1. Mount the product on the wall bracket and  make sure it is properly fixed to the left and 
right plastic hangers.  
2. Be careful when installing the product on the  bracket as fingers can be caught in the holes.  
3. Make sure the wall bracket is securely fixed to 
the wall, or the product may not stay in place 
after installation.  
Tighten the 4 screws in step 2 (plastic hanger + 
screw  B)to the rear holes of the product. 
Remove safety pin (
3) and insert the 4 product 
holders into the corresponding bracket holes ( 1). 
Then place the product( 2) so that it is firmly fixed 
to the bracket. Make sure to re-insert and tighten 
the safety pin ( 3) to securely hold the product to 
the bracket.  
 
A. Monitor  
B. Wall Bracket  
C. Wall  
 
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2°before installing it on the wall.   
						

							1. Fix the product to the wall bracket.  
2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.  
3. You can adjust the bracket angle between -2°and 15 °.   Make sure to use the top center, and not the 
leftor the right side of the product to adjust the 
angle. 
						

							 Mechanical Lay-out
 | Monitor Head  | Stand  | Speaker  | Installation VESA Bracket  | Wall Bracket Installation  
1. Mechanical Lay-out
2. Monitor Head
Dodatak 


						

							3. Stand
4. Speaker
5. Installation VESA Bracket 
zWhen installing VESA, make sure to comply with the international VESA standards.  zPurchasing VESA Bracket and Installation Information : Please contact your nearest Samsung Distributor to place 
an order. After your order is placed, installation professionals will visit you and install the bracket.  
zAt least 2 persons are needed in order to move the LCD Monitor.  zSamsung is not responsible for any product damage or any injury caused by installation at customers discretion.  
Dimensions 
						

							For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
6. Wall Bracket Installation 
zContact a technician for installing the wall bracket.  zSamsung Electronics is not responsible for any damages to the product or harm to customers when the 
installation is done by the customer.  
zThis product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. 
 
Components
Only use the components and accessories shipped with the product.
` 
Wall Bracket 
(1)Hinge 
(Left 1, Right 1)Plastic Hanger
(4)Screw(
A)
(11)Screw(
B)
(4)Anchor 
(11)
 
Wall Bracket Assembly
 
Insert and tighten the Captive Screw in the 
direction of the arrow.  
When done, mount the wall bracket on the wall.  
 
A. Captive Screw  
B. Wall Bracket  
C. Hinge (Left) 
D. Hinge (Right) 
						

							There are two hinges(left and right). Use the correct one.
Before drilling into the wall, check if the length 
between the two locking holes at the back of the 
product is correct. 
If the length is too short or long, loosen all or 
some of the 4screws on the wall bracket to adjust 
the length. 
 
A. Length between the two locking holes
Check the installation diagram and mark the drill 
points on the wall. Use the 5.0 mm bit to drill 
holes deeper than 35 mm. Fix each anchor in the 
corresponding hole. 
Match each of the brackets and hinge holes to 
the corresponding anchor holes and insert and 
tighten the 11 screws 
A.
 
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the 
screw are the same)
  
						

							Remove the 4 screws on the back of the 
product. 
Insert the screw 
B into the plastic hanger. 
 
1. Mount the product on the wall bracket and 
make sure it is properly fixed to the left and 
right plastic hangers.  
2. Be careful when installing the product on the 
bracket as fingers can be caught in the holes.  
3. Make sure the wall bracket is securely fixed to 
the wall, or the product may not stay in place 
after installation.  
Tighten the 4 screws in step 2 (plastic hanger + 
screw 
B)to the rear holes of the product. 
Remove safety pin (
3) and insert the 4 product 
holders into the corresponding bracket holes (
1). 
Then place the product(
2) so that it is firmly fixed 
to the bracket. Make sure to re-insert and tighten 
the safety pin (
3) to securely hold the product to 
the bracket.  
 
A. Monitor  
B. Wall Bracket  
C. Wall  
 
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2°before installing it on the wall.
  
						

							1. Fix the product to the wall bracket.  
2. Hold the product at the top in the center and pull it forward 
(direction of the arrow) to adjust the angle.  
3. You can adjust the bracket angle between -2°and 15 °.  Make sure to use the top center, and not the 
leftor the right side of the product to adjust the 
angle. 
						

							Select Language Main Page
Model
The color and appearance of the product may vary depending on the model, and the product specifications are 
subject to change without prior notice for reasons of performance enhancement. 
Connections 
Installing the Stand KIT
 
 
Note
• Only the supplied bolts should be used.
 
Caution
Samsung Electronics will not be responsible for damages caused by using a base other than those 
specified. 
 
Installing the Semi Stand 
 
Left stand Right stand 
Caution
Make sure to install the stand with the Caution label 
folded backwards. 
 
1) A Cover-Protector is used to protect the hole at the bottom of the LCD Display , where the stand is  inserted. Be sure to remove the Cover-Protector when attaching the provided Semi Stand or Stand KIT 
(sold separately) and cover the hole using the  Cover-Hole when attaching the wall mount kit.
2) Set up the left and right stands respectively.
3) Insert the stand into the hole at the bottom of the LCD Display.  Insert the screw into the hole indicated and tighten it. (M4 x L15)
 
Caution
Safety Instructions 
Introduction 
Connections 
Installing the Stand KIT 
Connecting the LCD 
Display 
 
Using the Software 
Adjusting the LCD Display  
Troubleshooting 
Specifications 
Information 
Appendix 
 
 
Dodatak 


						

							This stand is designed for adjusting the screen angle. The company is not responsible for any problem 
caused when using this stand. Under no circumstances use the product as a stand for placing something on. 
 
 
Installing the Stand KIT (sold separately) 
 
1) A Cover-Protector is used to protect the hole at the bottom of the LCD Display , where the stand is  inserted. Be sure to remove the Cover-Protector when attaching the provided Semi Stand or Stand KIT 
(sold separately) and cover the hole using the  Cover-Hole when attaching the wall mount kit.
2) Ensure that the parts are inserted in the right direction and in the right place. (M4 × L15)
3) Insert the stand into the hole at the bottom of the LCD Display.
4) Insert the screw into the hole indicated and tighten it. (M4 × L15)
 
Connecting the LCD Display 
 
 
Using a Power cord with Earth
  In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in 
correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect 
the AC power in advance.
 
Note
• AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected  to the LCD Display. For detailed information on connecting AV input devices, refer to the User Controls 
under Adjusting Your LCD Display.
 
 
Connecting to a Computer